Owner's Manual

ManualsBrandsLinear ManualsMisc ElectronicsLinear 212xt

SPECIFICATIONS:

MECHANICAL:

XT CASE DIMENSIONS:

2.75”w x 4.50”h x 1.50”d

PROGRAMMER CASE DEMENSIONS:

2.75”w x 4.50”h x 2.50”d

ELECTRICAL:

VOLTAGE:

12-24 Volts AC/DC (selected by jumper)

CURRENT:

@12-24 Volts AC/DC- 20ma typical-150 max with all relays

energized

OUTPUTS:

Main relay: 8 Amp, Form-C @ 24volts-10 AMP surge

Relays 2, 3, & 4 are Form C relays-1 AMP MAXIMUM

212xt Wiring Diagrams and Specifications

RELAY

SW1

NC C

P1-REX INPUT

P2-RELAY 2

P3-RELAY 3

P4-RELAY 4

P5-VOLTAGE SELECTOR

SW1-PROGRAMMING SWITCH

P5*

*P5 is the Voltage Selector. With the jumper in position one, 12-15vdc only operation is

selected. With the jumper in position two 15-24vdc/12-24vac operation is selected.

Packing Checklist:

Xtreme™ Keypad

212 XT Programming Controller

Four Conductor Wire Harness (1)

Three Conductor Wire Harness (4)

Slotted Screws (4)

Plastic Anchors (4)

Machine Screws (2)

5/64 Allen Head Wrench (1)

Tech Supp. With Warranty card

Command & Control Features and Programming Guide

INTERNATIONAL

ELECTRONICS, INC

INTERNATIONAL ELECTRONICS, INC.

427TURNPIKE STREET, CANTON,MA 02021 U.S.A.

800-343-9502, 617-821-5566 (FAX)617-821-4443

P5*

Position

12-15VDC

12-24VAC

6061170 REV 1.01

Voltage Selection Settings

15-24VDC

ENVIRONMENTAL:

TEMPERATURE:

-20°F TO 130°F (-28°C TO 54°C)

4 5 6

7 8

( White / Yellow )

( White / Black )

( Red )

( Black )

Wire Xtreme Pad

to Appropriate color

wires on Programmer

(Red to Red, etc.)

Visit our website for Access Control & Glassbreak information,

New Products, Specifications, Applications, Seminars, and Partners

@ WWW.IEIB.COM

Position

Summary of content (3 pages)

PAGE 1
212xt Wiring Diagrams and Specifications Voltage Selection Settings Wire Xtreme Pad to Appropriate color wires on Programmer P5* (Red to Red, etc.) 1 2 3 4 5 6 Position 2 Position 1 12-24VAC 12-15VDC 15-24VDC ( White / Yellow ) ( White / Black ) ( Red ) ( Black ) 7 8 9 * 0 # P2 P3 P4 P1 P5* RELAY SW1 + *P5 is the Voltage Selector. With the jumper in position one, 12-15vdc only operation is selected. With the jumper in position two 15-24vdc/12-24vac operation is selected.
PAGE 2
Basic Access Control with an Electric Door Strike Normally Open Remote Switch NO NC NO C OUTPUT 2 White/Orange Remote Triggering Input Not Used Remote Triggering Input Normally Open Remote Switch NC NO NC C C OUTPUT 3 OUTPUT 4 White Remote Triggering Input Not Used Remote Triggering Input -Jumper on 2&3 for 12-15 VDC only -Jumper on 1&2 for 15-24 VDC 12-24 VAC Brown TS 1 Programming Switch Basic Access Control with an Magnetic Lock SW1 NO White/Orange NC NO C OUTPUT 2 OUTPUT 3 Whit
PAGE 3
Auxiliary Outputs The Extreme™ programming controller comes equipped with 3 auxiliary relay outputs and 3 internal timer circuits. The outputs can operate from 01-90 seconds, or you can program them to latch in the energized position until the same code, or another latch code is entered. These outputs maybe used to turn on or off, or shunt most devices after a valid code entry. The relays are form C relay and are rated to handle one (1) amp of current at either 12 volts or 24 volts, type AC or DC.