Owner's Manual

ManualsBrandsLinear ManualsMisc ElectronicsLinear 232xt

SPECIFICATIONS:

MECHANICAL:

XT CASE DIMENSIONS:

2.75”w x 4.50”h x 1.50”d

PROGRAMMER CASE DIMENSIONS:

2.75”w x 4.50”h x 2.50”d

ELECTRICAL:

VOLTAGE:

12-24 Volts AC/DC (selected by P5 jumper)

CURRENT:

@12-24 Volts AC/DC- 20ma typical-150ma max with all

relays energized

OUTPUTS:

Main relay: 8 Amp, Form-C @ 24volts-10 AMP surge

Relays 2, 3, & 4 are Form C relays-1 AMP MAXIMUM

232xt Wiring Diagrams and Specifications

RELAY

V+ V

SW1

NC C

P1-REX INPUT/DOOR POSITION INPUT

P2-ALARM SHUNT RELAY

P3-FORCED DOOR RELAY

P4-DOOR AJAR RELAY

P5-VOLTAGE SELECTOR

SW1-PROGRAMMING SWITCH

P5*

*P5 is the Voltage Selector. With the jumper in position one, 12-15vdc only operation is

selected. With the jumper in position two 15-24vdc/12-24vac operation is selected.

Packing Checklist:

Xtreme™ Keypad

232 XT Programming Controller

Four Conductor Wire Harness (2)

Three Conductor Wire Harness (4)

Slotted Screws (4)

Plastic Anchors (4)

5/64 Allen Head Wrench (1)

Machine Screws (2)

Tech Supp. With Warranty card

ACCESS CONTROL Features and Programming Guide

INTERNATIONAL

ELECTRONICS, INC

INTERNATIONAL ELECTRONICS, INC.

427TURNPIKE STREET, CANTON,MA 02021 U.S.A.

800-343-9502, 617-821-5566 (FAX)617-821-4443

P5*

Position

12-15VDC

12-24VAC

6063170 REV 1.01

Voltage Selection Settings

15-24VDC

ENVIRONMENTAL:

TEMPERATURE:

-20°F TO 130°F (-28°C TO 54°C)

4 5 6

7 8

( White / Yellow )

( White / Black )

( Black )

Wire Xtreme Pad

color to color to the

wires on Programmer

(Red to Red, ect.)

Visit our website for Access Control & Glassbreak information,

New Products, Specifications, Applications, Seminars, and Partners

@ www.ieib.com

Position

Summary of content (6 pages)

PAGE 1
232xt Wiring Diagrams and Specifications Voltage Selection Settings Wire Xtreme Pad color to color to the wires on Programmer P5* Position Position 1 12-24VAC 12-15VDC (Red to Red, ect.) 1 2 3 4 5 6 15-24VDC ( White / Yellow ) ( White / Black ) ( Black ) 7 8 9 * 0 # P2 P3 P4 P1 P5* RELAY SW1 V+ V *P5 is the Voltage Selector. With the jumper in position one, 12-15vdc only operation is selected. With the jumper in position two 15-24vdc/12-24vac operation is selected.
PAGE 2
WIRING THE XTREME™ The Xtreme™ keypad is a device which you choose to place either inside or outside the door. IEI manufactures several other devices to choose from; keypads, magnetic card readers, proximity card readers, and touch chip readers. Choosing the correct device for the application is important. IEI manufactures light traffic and heavy traffic devices. If you are not sure which device to utilize, please call us at 1-800-343-9502.
PAGE 3
Propped Door Relay This output is utilized to inform personnel that the door is being held, or propped open, after a valid entry. To accomplish this, the Xtreme™ programming controller comes equipped with a relay and an internal timer circuit that is designated for this purpose. The form C relays are rated to handle one (1) amp of current at either 12 volts or 24 volts, type AC or DC, and can turn on or off one leg of power to a warning device. Warning device not included with IEI equipment.
PAGE 4
Forced Door Relay This output is utilized to inform personnel that the door had been opened without authorization. To accomplish this, the Xtreme™ programming controller comes equipped with a relay and an internal timer circuit that is designated for this purpose. The form C relays are rated to handle one (1) amp of current at either 12 volts or 24 volts, type AC or DC, and can turn on or off one leg of power to a warning device. Warning device not included with IEI equipment.
PAGE 5
Alarm Shunt Relay Xtreme™ CONTROL RELAY BOARD The Alarm shunt relay may be necessary to use when a security system or other type of system has already been in existence. The Alarm shunt relay keeps the alarm from activating when the door is opened, by keeping either a closed or opened state on the existing alarm panels zone. The Alarm shunt relay operates when the set of normally closed door contacts has been opened after a valid code entry. No programming required.
PAGE 6
Basic Access Control with an Electromagnetic Lock Normally Open Switch NO Normally Closed Door Contacts Input Loop Common Door Position Input Timed Egress Input NC NO C NC NO C Switch -Jumper on 2&3 for 12-15 VDC only -Jumper on 1&2 for 15-24 VDC 12-24 VAC TS 1 SW1 * If no contact in being used it must be jumped closed.