Home Security System User Manual

Copyright © 2008 Linear LLC Issue Date November 4, 2008 228490 C
DXS-65
Supervised Emergency
Alarm Transmitter
Installation
Instructions
1. PRODUCT DESCRIPTION
The Model DXS-65 is a supervised water-resistant emergency alarm transmitter designed for use with Linear’s
PERS Consoles and can also be used with other Linear DX or DXS format receivers. This transmitter features
a large, easy to find, HELP button. An optional blank face aqua colored button is included for custom labeling or
alternate uses. Pressing the button activates the transmitter and sends a digitally coded wireless signal to its
companion receiver. To insure sending a complete signal, press the transmitter button for a minimum of
two seconds.
The transmitter can be wall mounted using the integral snap-on mounting bracket, or simply be placed on a table.
Four rubber “feet” are supplied for table-top use. The DXS-65 is factory set to a unique code, so no field coding is
required. The transmitter can send a signal for up to 10 seconds per activation. The red operation indicator lights
when the transmitter is activated.
An optional supervisory status timer is included in the DXS-65. Status transmissions occur every two hours and
inform the receiver of the condition of the transmitter and its batteries. The factory setting has the status timer
disabled. The status timer can be enabled by pressing the HELP button continuously for five seconds. The red
operation indicator will blink as the status timer is enabled. The status timer can be disabled by removing the
power from the transmitter. NOTE: If the status timer is required for the installation, be sure to enable it after
replacing the transmitter’s batteries.
Every two hours the transmitter tests for low batteries. This test takes place even if the status transmissions have
not been enabled. If the batteries test low, a low battery signal is sent to the receiver.
Each transmitter is sealed to provide water-resistance. The transmitter is powered by two 2032 “coin-cell” batteries
and must be disassembled to replace the batteries.
Before system testing and operation, each transmitter must be programmed into its receiver. Refer to the receiver’s
or Console’s instructions for details on programming transmitters into the system. When using a PERS or DVS
Console, be sure to program the receiver for the correct sensor type and supervision option using the
RA-2400 programming software. (Note: DVS Consoles default the DXS-65 as an arm/disarm transmitter.)
2. FEATURES
3. OPTIONAL WALL MOUNTING 4. STATUS SUPERVISION OPTION 5. PROGRAM TRANSMITTER INTO RECEIVER
6. TESTING TRANSMITTER 7. BATTERY REPLACEMENT OR BUTTON EXCHANGING LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months. This
warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal
distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their
selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part
of Linear LLC for consequential damages arising out of or in connection with use or performance of this
product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal,
installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied
warranties for fitness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu of all other
warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear
Technical Services at 1-800-421-1587 for an RPA# and other important details.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need in portable wireless
signaling. However, there are some limitations which must be observed.
• ForU.S.installations only:The radios are requiredto comply withFCC Rules and Regulationsas Part 15
devices. As such, they have limited transmitter power and therefore limited range.
• Areceivercannotrespondtomorethanonetransmittedsignalatatimeandmaybeblockedbyradiosignals
that occur on or near their operating frequencies, regardless of code settings.
• ChangesormodicationstothedevicemayvoidFCCcompliance.
• Infrequentlyusedradiolinksshouldbetestedregularlytoprotectagainstundetectedinterferenceorfault.
• Ageneralknowledgeofradioanditsvagariesshouldbegainedpriortoactingasawholesaledistributoror
dealer, and these facts should be communicated to the ultimate users.
USA & Canada [phone] & [phone]
[phone] - Toll Free FAX [phone]
www.linearcorp.com
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,DXS-65; LINEAR P/N: 228490 C - INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 11.000” x 8.500”; SCALE: 1-1
BY
DXS-65
TRANSMITTER
TRANSMIT
INDICATOR
ACTIVATION
BUTTON
MOUNTING
PLATE
TABLE-TOP
FEET (4)
MOUNTING
SCREWS (2)
OPTIONAL BLANK
AQUA BUTTON
TO ENABLE THE HOURLY
SUPERVISORY STATUS
REPORTS, PRESS THE HELP
BUTTON FOR 5 SECONDS
RED INDICATOR
WILL BLINK WHEN
STATUS IS ENABLED
NOTE: THE RED INDICATOR
WILL NOT LIGHT EACH TIME
AN AUTOMATIC HOURLY
STATUS REPORT IS SENT
IMPORTANT!
AFTER ENABLING STATUS REPORTS ON THE
TRANSMITTER, BE SURE TO SET THE SENSOR NUMBER
IN THE PERS OR DVS CONSOLE TO
SUPERVISED USING THE
RA-2400 PROGRAMMING SOFTWARE
PERS-3600B
CONSOLE
PLACE THE CONSOLE OR RECEIVER
INTO PROGRAMMING MODE
ACTIVATE THE TRANSMITTER
TO PROGRAM IT INTO THE
CONSOLE OR RECEIVER
1
2
NOTE: IF THE TRANSMITTER
HAS SUPERVISION ENABLED,
BE SURE TO PROGRAM THE
CONSOLE WITH THE SENSOR
OPTION SET AS SUPERVISED
FOR THIS TRANSMITTER
PERS-3600B
CONSOLE
PLACE THE CONSOLE OR RECEIVER
INTO TEST MODE
ACTIVATE THE TRANSMITTER,
VERIFY THAT THE SIGNAL WAS
RECEIVED
1
2
NOTE: TO VERIFY THE RADIO
RANGE, BE SURE TO TEST
THE TRANSMITTER FROM THE
INTENDED MOUNTED OR
TABLE-TOP LOCATION
TEST SYSTEM WEEKLY!
1
2
TWIST A COIN OR SCREWDRIVER IN
THE SLOT ON TOP OF TRANSMITTER
TO OPEN THE CASE
REMOVE THE CASE TOP, BUTTON, SILICONE
SEAL, AND LIFT OUT THE TRANSMITTER
CIRCUIT BOARD
3
4
RE-ASSEMBLE THE UNIT
BY REVERSING THE STEPS
5
TEST THE TRANSMITTER
AFTER RE-ASSEMBLING
NOTE: IF THE STATUS TIMER IS REQUIRED
FOR THE INSTALLATION, BE SURE TO ENABL
E
IT AFTER REPLACING THE BATTERIES
REPLACE THE BATTERIES WITH
TWO TYPE MAXELL CR2032
200mA HR OR DURACELL DL2032
COIN-CELL BATTERIES,
PLUS SIDE AWAY FROM THE
CIRCUIT BOARD
ATTACH WALL
MOUNT BRACKET
WITH TWO SCREWS
HOOK TOP OF TRANSMITTER
ONTO THE BRACKET TABS
SWING TRANSMITTER
ONTO BRACKET
TO REMOVE
TRANSMITTER
PRESS TAB ON
BRACKET
FOR NON-WALL MOUNT APPLICATIONS,
STICK THE FOUR ADHESIVE "FEET"
ONTO THE MOUNTING BRACKET