Quick Start Manual

The HD18 & HD36 Hinged Door Depth Extension Kit attaches to the
OpenHouse Models H318 and H336 structured wiring enclosures. The door kit
adds the feature of an injection molded,
lockable, light weight, removable door
to an enclosure. The door kit adds over
1” of depth to the enclosure allowing
larger power supplies to be used with
the Model H290 & H291 AC power
accessories. Component cooling is also
improved using the door kit. The door kit
can snap to, as well as be screwed to
an enclosure. The door is supplied with
a snap-action lock that retains the door
to the door frame when closed. The
optional Model H208 keylock can be
installed for increased security.
Installation
➀
PREPARE THE DOOR KIT FOR INSTALLATION
The door kit can be installed onto the
mounted enclosure with the door on
or off the door frame. To remove the
door from the door frame, open, lift and
remove the door. Carefully set the door
aside.
➁
ATTACH THE TOP EDGE OF THE FRAME TO THE ENCLOSURE
The inside top edge of the door frame
has tabs that slide behind the top inside
edge of the metal enclosure. Align the
frame on the enclosure and slide the
top tabs into place as shown in the
figure.
➂
SNAP THE BOTTOM EDGE OF THE FRAME TO THE ENCLOSURE
Swing the bottom edge of the frame
towards the bottom edge of the
enclosure. Lift the two locking tabs
slightly and carefully press firmly on
the bottom edge of the frame to engage
the bottom locking tabs with the bottom
inside edge of the metal enclosure.
✔ NOTE: If the enclosure is mounted too deep in the wall to
utilize the “snap action mounting”, adjust the enclosure
depth or use the frame retaining screws exclusively to attach
the frame to the enclosure.
HD36
HD18
HD18 & HD36 Hinged Door Kit
Installation
➃
INSTALL FRAME RETAINING SCREWS (OPTIONAL)
The door frame can be secured with
the tri-lobular screws provided (Model
HD18 has 4 screws, Model HD36 has 6
screws). The screws can also be used
when the enclosure is mounted too
deep in the wall to use the door frame
tabs. Insert and start the threads on
all the screws first, then tighten each
screw.
➄
INSTALL MODEL H208
KEYLOCK (OPTIONAL)
The door is designed to accept the
OpenHouse Model H208 keylock (sold
separately). To install the keylock, first
remove the keyhole plug, then install
the H208 keylock as shown in the
figure. (The keylock carton also shows
the keylock assembly.)
➅
HANG THE DOOR ON THE DOOR FRAME
Replace the door if it was removed from
the door frame during installation. Align
the door hinges over the posts on the
door frame. Carefully lower the door
onto the door frame, close the door and
snap it shut.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,HD18/HD36 - LINEAR P/N: 224151 A - INK: BLACK - MATERIAL: 113 GSM WHITE COATED - SIZE: 11.000” X 15.000” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE, 2-FOLD HORIZONTAL INTO THIRDS (FINISH HAS LOGOS SHOWING) - SIDE 1 OF 2
LIFT UP ON THE OPEN DOOR
TO REMOVE IT FROM TH
E
DOOR FRAME
DOOR
DOOR FRAM
E
SLIDE THE TOP DOOR FRAME
TABS UNDER THE TOP LIP OF
THE METAL ENCLOSUR
E
TABS
DOOR FRAME ENCLOSURE
LIFT BOTTOM TABS UP
AND SNAP BOTTOM EDGE
OF THE DOOR FRAME
ONTO THE ENCLOSUR
E
LIFT
TABS
THE FRAME RETAINING SCREWS
CAN BE USED TO ATTACH TH
E
DOOR FRAME TO THE ENCLOSURE
1
REMOVE THE KEYHOLE
PLUG FROM THE DOOR
2
REMOVE THE SWING ARM FROM
THE KEYLOCK AND INSTALL TH
E
KEYLOCK INTO THE DOOR KEYHOLE
DOOR
KEYHOLE
3
INSTALL THE SWING ARM ON THE
KEYLOCK WITH THE SCREW,
WASHER AND LOCKWASHER
4
CHECK THE ACTION OF THE
KEYLOCK
UNLOCK
LOCK
CAREFULLY LOWER THE DOOR
ONTO THE DOOR HINGES ON
THE DOOR FRAM
E
DOOR
DOOR FRAM
E
®