2X4 Switcher/Splitter For d Model # HDMI-SW-2X4M USER MANUAL www.linearcorp.
ASKING FOR ASSISTANCE Technical Support: Telephone (800) 421-1587 (760) 438-7000 Fax (760) 438-7199 Technical Support Hours: 6:30 AM - 4:30 PM PST Monday through Friday. Email: techsupport@linearcorp.com Website: www.linearcorp.com Notice Linear LLC reserves the right to make changes in the hardware, packaging and any accompanying documentation without prior written notice.
TABLE OF CONTENTS 1. Introduction / Operation Notes 2. Features 3. Panel Descriptions 4. Connecting and Operating the 2X4 Switcher/Splitter For HDMI 5. RMT-2 Installation 6. IR Code Configuration 7. Wiring Diagram 8. Specifications 9.
INTRODUCTION The Linear 2x4 Switcher/Splitter for HDMI is equipped with two HDMI inputs and four HDMI outputs. Two inputs accommodate the simultaneous connection of up to two high definition video sources, such as satellite systems and HD DVD players. Four outputs send the high definition audio/video signals to up to four high definition displays. Switching is done via the IR remote that is provided with the unit. How It Works You simply connect all your sources to the switcher’s HDMI inputs.
FEATURES Features • Switch easily between any two HDMI sources • Outputs are mirrored to four HDMI displays simultaneously • Extends the range of the HDMI compliant device by equalizing and reclocking the HDMI signal • Supports resolutions up to 1080p, 2K and 1920 x 1200 • HDMI/HDCP compliant Includes: (1) 2X4 Switcher/Splitter for HDMI (2) 6 ft HDMI cables (M-M) (1) 5V DC Power Supply (1) RMT2-IR remote (1) User’s Manual NOTE: *When used with a HDMI to DVI Adapter 2
PANEL DESCRIPTIONS Front Panel IR Eye Input LED Indicator Power LED Indicator IR Eye Extension Port Back Panel HDMI Input 2 HDMI Input 1 HDMI Output 1* HDMI Output 2 *See note on page 4 3 HDMI Output 3 5V DC Power HDMI Input Output 4
CONNECTING THE 2X4 SWITCHER/SPLITTER FOR HDMI How to Connect the 2X4 Switcher/Splitter For HDMI 1. Connect the supplied cable from the HDTV HDMI source into the HDMI input port 1 of the 2X4 Switcher/Splitter for HDMI. 2. Connect the second HDTV HDMI source to HDMI input port 2 on the 2X4 Switcher/ Splitter for HDMI using a user supplied HDMI cable. 3. Connect the display(s) to the HDMI output port(s)* of the 2X4 Switcher/Splitter for HDMI using user supplied cable(s). 4.
RMT2-IR INSTALLATION 1. Remove battery cover from the back of the RMT2-IR remote. 2. Verify that dip switches 1 & 2 are in the down (OFF) position. (See page 6) 3. Insert the battery, hold the battery so that you can see the positive side facing up. The side that is not marked must be facing down. 4. Test the RMT2-IR remote by pressing ONLY one button at a time. The indicator light on the remote will flash once each time you press a button.
IR CODE CONFIGURATION How to Resolve IR Code Conflicts In the event that IR commands from other remote controls conflict with the supplied RMT-2IR remote control, changing the remote channel will alleviate this issue. The RMT-2IR remote control and the 2X4 Switcher/Splitter for HDMI have DIP SWITCHES for configuring the remote channel that both units use to communicate. These settings must match each other for proper operation. The 2 DIP SWITCH bank on the RMT-2IR is located underneath the battery cover.
Maximum HDMI cable length is 15 ft at 1080P resolution without the use of an HDMI-SB or HDMI-CAT5-EXT WIRING DIAGRAM 8
SPECIFICATIONS VideoAmplifier Bandwidth: .............................................................. 165 MHz Input Video Signal: ...................................................................... 1.2 Volts p-p Input DDC Signal: .................................................................. 5 Volts p-p (TTL) Single Link Range: ........................................................... 1080p/1920 x 1200 HDMI Connector: ............................................................
WARRANTY Note: These products are designed to be installed and serviced by trained professional installation companies. Linear LLC warrants this product to be free from defects in material and workmanship. For the term of the warranty, see the list of products below. The Warranty Expiration Date is reflected by a date code that is affixed to all of Linear’s products. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels.
H D MI -S W-2X 4M (7 6 0 ) 4 3 8 -7 0 0 0 (80 0 ) 4 2 1 -1 5 8 7 FA X (8 0 0 ) 4 6 8-1340 www. lin e a rc o rp .
