User's Manual

Pairing&Connection
Dual Mode
As soon as take out both earphones at the same time from
charging box, they will power on automatically with voice prompts
“Power on”. Soon later, L&R earphones pair each other
automatically and voice prompts“Connected”, “Left channel/Right
channel” ; The main device (L) led indicator blinks in blue and
white, sub-device led indicator blinks in blue color only, 7 seconds
once.
(For the first time, connecting both earphones takes about 15-20
seconds)
Single Mode
If only take out left or right earphone from charging box ,it will
power on automatically with voice prompts “Power on ” ,”Pairing
mode” ,L/R earphone led indicator blink in blue and white color.
When you hear voice prompts “Pairing mode”, it means both
earphones start connecting with cell phone. Activate your cell
phone bluetooth and search “ HYPERSONIC ”. Enter connection
password “0000”, voice prompts “Pairing successful”, it means
both earphones connected cell phone successfully. After paired,
L earphone led indicator blink in blue and white color, R earphone
led indicator blink in blue 7 seconds once.
Start to enjoy music after you finished above steps.
The HYPERSONIC’s left and right earphones can be used
together in stereo or used individually in mono.
Both of L & R
earphones
speech recognition
program
on/off
1S

True Wireless Earphones
User Manual
HYPERSONIC
Both earphones have one button each. While playing music, press
the button on either side once to pause/play a song, press it twice
to go to the next track, and press it three times to go to the
previous track.
Press the either earphones’s button for one second to turn on your
device's speech recognition program (Such as Siri, Cortana,
Google Now, etc.).
Operation
Power off: press and hold either earphone’s button for a few
seconds until you hear a beep and the voice prompt “Power off.”
The other earphone will turn off automatically.
If not placed in the charging box, turning the devices on again will
require pressing both earphones' buttons for a few seconds until
you hear the voice prompt “Power on.”
If you receive a phone call while music is playing, the track will
pause automatically. Press the button on either side once to
accept the call, and press it twice to reject the call.
While in a call, press the button on either side twice to switch the
speaker to your cell phone.
1.
2.
3.
Under power off situation,long press both left and right earphone
power buttons,until the blue and white led indicator blinks to clear
the pairing record,after the led indicator flash the white and blue
light three times quickly ,delete the pairing record successfully
.This operation will take about 10s-20s.
The function can be operated when the earbuds with pairing issue
,after the operation ,power on both of earphones at the same time
, L&R earphones paired automatically .
If the earphones do not connect
Hold both buttons down until you hear “Power off”.
Hold both buttons again and you will hear “power on” but do not let
go until you hear “Pairing mode”, and the earphones will have
flashing blue and white lights, and after a few seconds, “Pairing
successful, left channel right channel” This means that the both
earphones are successfully connected to each other.
You will hear “Pairing mode” again, and that is for the earphones to
connect to your device. Select “HYPERSONIC” from your device's
list and enter the password “0000” (if needed) and wait for the voice
prompt “Pairing successful” and the earphones are ready for use.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may
cause undesired operation.
Earphones working status and prompts
Master device: Left channel, call, music
Sub-device: Right channel, music,call
Pair name:HYPERSONIC
Pair Password: 0000
Exceed bluetooth connection distance or not to connect within 10
minutes, earphones power off automatically.
IOS7.0, Android5.0 and above systems,
left earphone(Master device) displays remaining battery power
Earphones prompts:
Power on
Pairing mode
Connected
Left channel/Right channel
Pairing successful
Low battery
Power off
1.
2.
1.
2.
3.
0%-25%
25%-50%
50%-75%
75%-100%
Fully Charged
Blinks once every two seconds
Blinks twice every two seconds
Blinks three times every two seconds
Blinks four times every two seconds
Stays on
Delete paired device function
Reconnection (Last memory)
White LED indicators on earphones lights on when it is charging
by the charging box ; and off when full charged .
If take out the earphones from the charging box, White LED
indicator on charging box blinks once only, it means the charging
box is low power and can not recharge the earphones, please
recharge the charging box as soon as possible.
As soon as put the earphones into charging box, they power off
automatically and start charging. (Stop playing music
automatically).
White LED indicator on charging box displays power status while
recharging :
Charging status display
1.
1.
2.
1.
2.
3.
4.
When you take out the devices from charging box and cell phone
bluetooth is activated, they reconnect automatically.
If only power on left earphone(Master device), it reconnects
automatically.
If only power on right earphone (sub-device), led indicator blinks in
blue & white color and switches to pairing mode.
When the devices are out of Bluetooth connect distance,it will be
disconnected automatically.
If back into the Bluetooth connect distance in 1min,it reconnects
with cell phone automatically.
If more than 1min,press the button of any device(L/R device) once
to reconnect with the cell phone.
2.
31 2 4