Lingenfelter SSR & Trailblazer High Flow Fuel Pump Upgrade Kit PN: L710111005 Revision - 1.5 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-8761 fax www.lingenfelter.
# 1 1 2 1 2 1 1 1 Part number TI-F0000267 TI-000107694/AA 12129494 TI-TF0001275 52545K51 22682111 L920010000 N/A Parts List Description 416 liter/hr E85 fuel pump Fuel pump wiring harness Metri-Pak terminals Convoluted fuel line Oetiker clamp Fuel sender O-ring seal LPE decal Installation instructions Optional Items • Kenne Bell Boost-A-Pump 40 amp module • PN KB-89068 for naturally aspirated applications (vacuum trigger switch) • PN KB-89069 for boosted applications (pressure trigger switch) • Fue
Thank you for purchasing the Lingenfelter Performance Engineering (LPE) SSR and Trailblazer High Flow Fuel Pump Upgrade Kit. This kit includes an E85-compatible fuel pump, along with other necessary components for installation of the high flow fuel pump into the stock module. The E85compatible fuel pump is capable of being pulse-width modulated (PWM).
. Carefully remove the fuel reservoir “bucket” from the fuel pump module assembly. 5. Using a small pocket screwdriver, carefully pry the fuel pump inlet sock & metal retaining clip from the bottom of the fuel pump. You will be reusing them when you reassemble the module. 6. Using wire cutters, cut the small static drain wire from the ground terminal of the fuel pump as close to the terminal as possible, as shown by the red arrow in the adjacent picture. 7.
8. Using a small screwdriver, remove the fuel line from the elbow fitting. Be careful not to damage the fitting. 9. Remove the old pump from the module by pushing the retaining latch out of the way and pushing the pump up towards the top of the module. 10. Tape off the jet pump and any other open fittings. 11. Mark 1 inch up from the bottom of the pump mounting sleeve on the module.
12. Using a die grinder or Dremel tool with a cutoff wheel, cut the bottom inch off of the pump mounting sleeve. 13. Remove any burrs or loose plastic. For best results use compressed air to blow off the module. 14. Using a heat gun and pair of needle nose pliers, expand one end of the new fuel line. Warm and expand the end of the fuel line just enough to fit over the fuel pump. WARNING: Make sure not to overheat or otherwise damage the fuel line, as doing so could cause the fuel line to leak. 15.
18. Feed the fuel line and the fuel pump wires up through the mounting sleeve on the module. 19. Slide the fuel pump up into position. You may need to turn the pump to index the sock so that it will fit into the bucket. 20. Remove the tape from the Jet pump and fittings. 21. Install the bucket onto the module making sure that it is fully seated and that all of the retaining tabs are latched. 22. Slide the remaining Oetiker clamp over the fuel line and slide it down out of the way. 23.
25. Strip roughly 1/4” off of the end of the small static drain wire and both wires of the fuel pump wire harness. 26. Using good quality terminal crimping tool, crimp one of the supplied terminals onto the small static drain wire along with the black wire of the fuel pump wiring harness. 27. Crimp the remaining terminal to the red wire of the fuel pump wiring harness. 28. Using a pin tool remove the white connector from the original fuel pump wires.
31. Connect the other end of the fuel pump harness to the connector attached to the fuel pump. NOTE: Make sure the wires are routed so that they can move freely and won’t interfere with the float operation. 32. Install the fuel pump module per OEM instructions. Congratulations, you have completed installation of the Lingenfelter SSR and Trailblazer High Flow Fuel Pump Kit Stock Trailblazer SS module vs LPE High Flow TBSS module, PN L710101108 test at 13.
Many other products are available from LPE for your Trailblazer SS or SSR, including low temperature thermostats, camshafts, supercharger kits, CNC ported cylinder heads, engine packages, ported throttle bodies, and port matched intake manifolds. Contact LPE, visit our web site, or contact your LPE distributor for information about our many other products. For additional product installation information and technical support, contact LPE or your LPE products distributor.
