Instructions / Assembly

EM-RF500W
RF201T1+RF201R-ULX3
Wireless Remote Control Outlet Indoor
with Countdown and Random mode 1+3
Instruction manual
Power input: 125V/60Hz
Power output: 1875W/15A (Max.)
Transmitter frequency: 433.92MHz
Remote transmitter battery: DC CR2032, 3V battery 1pc
Transmission range: up to 100ft
Caution
1. Appliances to be connected to the remote control
socket MUST NOT exceed the voltage and frequency
ratings as in “Specifications”.
2. Operation is subject to the following two conditions:
(1) this applicance may not cause harmful interference,
(2) this applicance must accept any interference received,
including interference that may cause undesired operation.
3. Only for indoor use and storage.
4. Low transmitter battery may lower the distance
between the transmitter and the receiver.
Plug the receiver into a standard AC
electrical wall socket.
Plug the appliance into the receiver
outlet.
2.
1 2
Before using the outlet with remote control, please pair as follows: 3.
Plug the outlet into the wall socket. When the receiver indicator light begins flashing,
press any ON or OFF button to pair the outlet to a corresponding number on the remote
control. If successfully paired, but you wish to unpair and tie to another corresponding
button, long-press the receiver button on the left side of the outlet until the light indicator
starts flashing. You may then press any new ON or OFF button on the remote control.
When the new pairing is successful, the light indicator on the outlet will stop flashing.
A.
When first using and pairing outlets to the remote control, please plug-in and pair one
outlet at a time.
B.
Unpairing: When the outlet and remote control are successfully connected,
long-press the receiver on the left side of the outlet for 3+ seconds and refer to step A.
C.
3
OFFON
4H 1H
3H 2H
-1-
-2-
-3-
-4-
OFFON
OFFON
OFFON
All ON will turn all outlets ON. All OFF will turn all outlets OFF.
This button is found at the top of the remote control on the right side.
To manually turn ON or OFF one outlet, press ON or OFF button on the remote control for numbers 1-4.
To utilize random mode, manually press the airplane logo button in the center of the remote. The light
indicator will flash softly and the outlet will turn ON randomly within 4-8 hours for 15 - 45 minutes
each cycle. To override, simply press the manual ON/OFF button linked to the outlet.
Note: Regardless of whether the light is ON or OFF, when random mode is selected the light will turn OFF.
If you are buying multiple sets (EM-RF300W, EM-RF500W, EM-1001) with learning code, the outlets are
compatible. Please refer to step 3 for pairing instructions.
To utilize countdown timer mode, manually press 1H/2H/3H or 4H. The light indicator will flash softly to
indicate the light is on countdown timer mode and the chosen duration. To override countdown timer
mode, simply press the manual ON/OFF button linked to the outlet. The countdown timer mode will only
shut down the connected device after the time selected is up.
4.
4
OFFON
4H 1H
3H 2H
-1-
-2-
-3-
-4-
OFFON
OFFON
OFFON
Remote Battery Replacement:
If operation of the receiver units becomes erratic, it may be necessary to
replace the battery in the hand-held remote unit. To do this, first remove
the battery compartment cover. Press the tray release button on the back
of the remote. Next, remove the depleted battery and discard according
to local ordinances. Be sure the correctly install the new battery. Replace
battery compartment cover and test by using it to control the Indoor
Remote Outlets.
Important: Install only new batteries of the same type in your product.
Failure to insert batteries in the correct polarity, as indicated in the battery
compartment, may shorten the life of the batteries or cause batteries to leak.
Do not mix old and new batteries. Do not mix Alkaline, Standard (Carbon-Zinc)
or Rechargeable (Nickel Cadmium)or (Nickel Metal Hydride) batteries. Danger
of explosion if battery is incorrectly replaced.
Batteries should be recycled or disposed of as per state and local guidelines.
WARNING: This product contains a button battery. If swallowed, it could
cause severe injury or death in just two hours. Seek medical attention
immediately.
LINK2HOME
1 YEAR LIMITED WARRANTY
IMPORTANT: Proof of Purchase is required to obtain
warranty service
Paragon Group USA Inc. warrants to the original owner that
our products will be free from defect in workmanship and
material for a period of ONE YEAR from the date of purchase.
Should any unit(s) prove to be defective during this period,
Paragon Group USA Inc. will be responsible for replacement
of the defective unit(s) only. Paragon Group USA Inc. is not
responsible for labor charges or any incidental or consequential
expenses.
Not Covered – Batteries are not covered by this warranty.
Repair service, adjustment and calibration due to misuse,
abuse or negligence are not covered by this warranty.
Unauthorized service or modification to this product or of any
furnished components will void this warranty in its entirety.
link2home.com
This warranty does not include reimbursement for inconvenience,
installation, set-up time, loss of use, postage, unauthorized
service, or other products used in conjunction with Link2Home
products.
For warranty service, please contact Paragon Group USA Inc.
Customer Service by Phone: [phone] or
e-mail: [e-mail].
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
Paragon Group USA Inc.
Link2Home Product Division
Englewood, NJ 07631
USA
1. Step A: Locate the battery compartment
on the back of the remote.
Push down and away to slide the
compartment cover off.
Step B: Remove the plastic battery tab
from the battery compartment
in the back of the remote control
to activate the pre-installed
battery.
Step C: Slide the compartment cover on
the remote and click securely
into place. Your remote is now
ready to use.