Instant Broadband™ Series Cable/DSL Routers Use this guide to install the following products: BEFSR41 ver. 2 EtherFast® Cable/DSL Router with 4-Port Switch BEFSRU31 EtherFast® Cable/DSL Router with USB Port and 3-Port Switch BEFSR11 ver.
COPYRIGHT & TRADEMARKS Copyright © 2002 Linksys, All Rights Reserved. Linksys and EtherFast are registered trademarks of Linksys. Instant Broadband is a trademark of Linksys. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. All other trademarks and brand names are the property of their respective proprietors.
Instant Broadband™ Series EtherFast® Cable/DSL Routers Table of Contents Chapter 1: Introduction The Linksys EtherFast Cable/DSL Router Features Package Contents for the 4-Port Router (BEFSR41) Minimum Requirements Package Contents for the 1-Port Router (BEFSR11) Minimum Requirements Package Contents for the 3-Port Router with USB (BEFSRU31) Minimum Requirements An Introduction to LANs and WANs IP Addresses Network Setup Overview 1 1 1 2 2 3 3 4 4 4 5 7 Chapter 2: Getting to Know the 4-Port EtherFast Ca
Instant Broadband™ Series EtherFast® Cable/DSL Routers Chapter 1: Introduction Appendix E: Twisted-Pair Cabling Crimping Your Own Network Cables 110 111 Appendix F: Finding the MAC Address and IP Address for Your Ethernet Adapter 112 Appendix G: Setting Up AOL® Broadband Cable & DSL AOL Broadband via Cable AOL Broadband via DSL 116 116 118 Appendix H: 4-Port Router Specifications 4-Port Environmental Specifications 119 119 Appendix I: 1-Port Router Specifications 1-Port Environmental Specification
Instant Broadband™ Series Package Contents for the 4-Port Router (BEFSR41) EtherFast® Cable/DSL Routers Package Contents Contents for for the the 1-Port 1-Port Router Router (BEFSR11) (BEFSR11) Package Figure 1-1 • • • • • 2 One EtherFast Cable/DSL Router with 4-Port Switch One Setup Wizard CD-ROM with User Guide Included One Power Adapter One Fast Start Guide One Registration Card (not shown) Figure 1-2 • • • • • One EtherFast 1-Port Cable/DSL Router One Setup Wizard CD-ROM with User Guide Included O
Instant Broadband™ Series Package Contents for the 3-Port Router (BEFSRU31) EtherFast® Cable/DSL Routers The Router’s firewall (NAT) protects your network of PCs so users on the public, Internet side cannot “see” your PCs. This is how your LAN, or network, remains private. The Router protects your network by inspecting the first packet coming in through the WAN port before delivery to the final destination on the LAN port.
Instant Broadband™ Series If you use the Router to share your cable or DSL Internet connection, contact your ISP to find out if they have assigned a static IP address to your account. If so, you will need that static IP address when configuring the Router. You can get the information from your ISP. Dynamic IP Addresses A dynamic IP address is automatically assigned to a device on the network, such as PCs and print servers.
Instant Broadband™ Series Chapter 2: Getting to Know the 4Port EtherFast® Cable/DSL Router EtherFast® Cable/DSL Routers The 4-Port Router’s Front Panel LEDs The 4-Port Router’s Rear Panel The Router’s ports, where network cables are connected, are located on the rear panel of the Router, as shown in Figure 2-1. Figure 2-2 Power Green. The Power LED lights up when the Router is powered on. Link/Act Green. The Link/Act LED serves two purposes.
Instant Broadband™ Series The WAN Indicators Link Act Diag Green. The Link LED lights up when a successful connection is made between the Router and your cable or DSL modem or network. Green. The Act LED flickers when the Router is sending or receiving data over the WAN port (to the Internet). Red. The Diag LED lights up when the Router goes through its self-diagnosis mode during every boot-up. It will turn off upon successful completion of the diagnosis.
Instant Broadband™ Series The Crossover Switch When “uplinking,” or connecting two pieces of network hardware together, such as a hub and a switch, a general rule of thumb is to plug one end of a network cable into a straight-through port, and the other end into a crossover port (uplink port). Standard ports are straight-through ports, and uplink ports are crossover ports. The 1 Port EtherFast® Cable/DSL Routers Full/Col If this LED flickers too often, there may be a problem with your connection.
Instant Broadband™ Series Chapter 4: Getting to Know the 3Port EtherFast Cable/DSL Router The 3-Port Router’s Rear Panel EtherFast® Cable/DSL Routers USB Compatibility Note: USB ports do not work on PCs running Windows 95 or NT. To use the USB port on the 3-Port Router, you must have Windows 98, 2000, Millennium, or XP installed on your PC. USB cannot run in a Windows 95 or NT environment. Also, your PC must have a USB port installed and enabled. Some PCs may have a disabled USB port.
Instant Broadband™ Series The 3-Port Router’s Front Panel LEDs Power Link/Act Full/Col Figure 4-4 Green. The Power LED lights up green when the Router is powered on. Green. The Link/Act LED serves two purposes. If the LED is continuously lit, the Router is successfully connected to a device through the corresponding RJ-45 port (1, 2, or 3). If the LED flickers, then that port is sending or receiving data to and from the network. When the Uplink port is in use, then Port 3 will be lit.
Instant Broadband™ Series EtherFast® Cable/DSL Routers Chapter 5: Connect the Router Connecting Your Hardware Together and Booting Up Overview 1. Before you begin, make sure that all of your hardware is powered off, including the Router, PCs, hubs, switches, and cable or DSL modem. Unlike a hub or a switch, the Cable/DSL Router’s setup consists of more than simply plugging hardware together.
Instant Broadband™ Series 3. Connect the Ethernet cable from your cable or DSL modem to the WAN port on the Router’s rear panel. This is the only port that will work for your modem connection. 4. Connect the power adapter to the Power port on the rear panel of the Router, and then plug the power adapter into a power outlet. Note: You should always plug the Router’s power adapter into a surge protecting power strip.
Instant Broadband™ Series Chapter 6: Installing the BEFSRU31’s USB Port Drivers EtherFast® Cable/DSL Routers 3. Select Search for the best driver for your device (Recommended), shown in Figure 6-2. Click the Next button. Use the enclosed USB cable to connect your PC to the Router; the Type A end connects to your PC’s USB port, while the Type B end connects to the Router’s USB port.
Instant Broadband™ Series 5. The Hardware Wizard will search the floppy, and a new window will appear (shown in Figure 6-4), notifying you that Windows is now ready to install the best driver for this device. Click the Next button to continue. EtherFast® Cable/DSL Routers 7. Windows will notify you that it has completed copying the driver files to your PC, as shown in Figure 6-6. Click the Finish button to complete the USB driver installation. Figure 6-4 6.
Instant Broadband™ Series 9. When your PC has finished restarting, click the Start button, and select Settings and Control Panel. Double-click Network. Make sure that TCP/IP is installed on your PC, as shown on the screen in Figure 6-8. By default, Windows 98 has TCP/IP installed. If TCP/IP is not installed, please go to “Appendix D: Installing the TCP/IP Protocol” for installation instructions. EtherFast® Cable/DSL Routers Installing the Windows 2000 Driver 1.
Instant Broadband™ Series 3. Insert the driver disk into the floppy drive, and when Windows asks you where to search for driver files, select Floppy disk drives only, as shown in Figure 6-11. Click the Next button. EtherFast® Cable/DSL Routers 5. When the Digital Signature Not Found screen appears, as shown in Figure 613, Windows will ask you if you want to continue the installation. Click the Yes button. Figure 6-11 Figure 6-13 4. Windows will notify you that it has found the driver files.
Instant Broadband™ Series 7. Windows will notify you that it has finished installing the driver files on your PC, as shown in Figure 6-15. Click the Finish button to complete the USB driver installation. EtherFast® Cable/DSL Routers Installing the Windows Millennium Driver 1. With the Router powered up and connected to your PC’s USB port using a USB cable, start up your PC in Windows Millennium. Figure 6-17 2. Windows will notify you that new hardware has been detected (see Figure 6-17).
Instant Broadband™ Series 4. Windows will ask you to restart your PC, as shown in Figure 6-20. Click the Yes button. EtherFast® Cable/DSL Routers Installing the Windows XP Driver 1. With the Router connected to your PC’s USB port using a USB cable, start up your PC in Windows XP. Figure 6-20 5. When your PC has finished restarting, click the Start button, and select Settings and Control Panel. Double-click Network and you will see a screen similar to that shown in Figure 6-21.
Instant Broadband™ Series 4. When the Hardware Installation screen appears shown in Figure 6-25, click Continue Anyway. EtherFast® Cable/DSL Routers Chapter 7: Configure the PCs Overview The instructions in this chapter will help you configure each of your computers to be able to communicate with the Router. To do this, you need to configure your PC’s network settings to obtain an IP (or TCP/IP) address automatically (called DHCP).
Instant Broadband™ Series Configuring Windows 95, 98, and Millennium PCs EtherFast® Cable/DSL Routers 3. Click the IP Address tab and select Obtain an IP address automatically, as shown in Figure 7-2. 1. Go to the Network screen by clicking the Start button. Click Settings and then Control Panel. From there, double-click the Network icon. 2. On the Configuration tab, select the TCP/IP line for the applicable Ethernet adapter, as shown in Figure 7-1.
Instant Broadband™ Series Configuring Windows 2000 PCs EtherFast® Cable/DSL Routers 4. Select Internet Protocol (TCP/IP), as shown in Figure 7-4, and click the Properties button. 1. Go to the Network screen by clicking the Start button. Click Settings and then Control Panel. From there, double-click the Network and Dial-up Connections icon. 2. Select the Local Area Connection icon for the applicable Ethernet adapter (usually it is the first Local Area Connection listed).
Instant Broadband™ Series Configuring Windows XP PCs EtherFast® Cable/DSL Routers 4. Select Internet Protocol (TCP/IP), as shown in Figure 7-7, and click the Properties button. The following instructions assume you are running Windows XP with the default interface. If you are using the Classic interface (where the icons and menus look like previous Windows versions), please follow the instructions for Windows 2000. 1. Click to the Network screen by clicking the Start button and then Control Panel.
Instant Broadband™ Series Chapter 8: Configure the Router This chapter will show you how to configure the Router to function in your network and gain access to the Internet through your Internet Service Provider (ISP). Detailed description of the Router’s Web-based Utility can be found in “Chapter 9: The Cable/DSL Router’s Web-based Utility.” Your ISP may require the use of a Host Name and Domain Name.
Instant Broadband™ Series EtherFast® Cable/DSL Routers DHCP or Obtain an IP Address Automatically PPPoE If your ISP says that you are connecting through DHCP or a dynamic IP address from your ISP, perform these steps: If your DSL provider says that you are connecting through PPPoE or if you normally enter a user name and password to access the Internet, perform these steps: A. Select Obtain an IP automatically as the WAN Connection Type, as shown in Figure 8-4. Figure 8-4 B.
Instant Broadband™ Series EtherFast® Cable/DSL Routers Chapter 9: The Cable/DSL Router’s Web-based Utility PPTP PPTP (shown in Figure 8-8) is a service used in Europe only. If you are using a PPTP connection, check with your ISP for the necessary setup information. Overview For your convenience, use the Router’s web-based utility to administer it. This chapter will explain all of the functions in this utility.
Instant Broadband™ Series A password request page, shown in Figure 9-2 will pop up. (Windows XP users will see a Connect to 192.168.1.1 window, shown in Figure 9-3). Leave the User Name field blank, and enter admin in the Password field. Then click the OK button. Router Administration EtherFast® Cable/DSL Routers • Device IP Address and Subnet Mask The values for the Router’s IP Address and Subnet Mask are shown here. The default values are 192.168.1.1 for the Device IP Address and 255.255.255.
Instant Broadband™ Series EtherFast® Cable/DSL Routers Static IP PPPoE Some DSL-based ISPs use PPPoE ( Po i n t - t o - Po i n t Protocol over Ethernet) to establish Internet connections for endusers. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you will have to enable it, as shown in Figure 9-5. Figure 9-5 User Name and Password Enter the User Name and Password provided by your ISP.
Instant Broadband™ Series PPTP RAS Point to Point Tunneling Protocol (PPTP) (shown in Figure 9-7) is a service that applies to connections in Europe only. R e m o t e A c c e s s Service (RAS) (shown in Figure 9-8) is a service that applies to connections in Singapore only. For users in Singapore, check with Singtel for information on RAS. Specify WAN IP Address This is the IP address that the Router has, when seen from the WAN, or the Internet.
Instant Broadband™ Series Password EtherFast® Cable/DSL Routers Status Figure 9-9 You should always have a password set for the Router. This is done through the Password tab, shown in Figure 9-9. The default password is admin. If you don’t change the password, all users on your network will be able to access the Router using the default password admin.
Instant Broadband™ Series shows the status of the Router’s DHCP server function, which is either enabled or disabled. • WAN These fields display the WAN IP Address, WAN Subnet Mask, and WAN Default Gateway IP Address of the Router, as seen by external users on the Internet. The DNS (Domain Name System) IP Address fields show the IP address(es) of the DNS currently used by the Router. Multiple DNS IP settings are common. In most cases, the first available DNS entry is used.
Instant Broadband™ Series EtherFast® Cable/DSL Routers Security Log Figure 9-12 The Log tab, shown in Figure 9-12, provides you with a log of all incoming and outgoing URLs or IP addresses for your Internet connection. To access activity logs, select the Enable option next to Access Log. This function can be disabled by clicking the Disable radio button. With logging enabled, you can choose to view temporary logs or have a permanent record, using the Logviewer software.
Instant Broadband™ Series Enforce ZoneAlarm Pro Security Check this box to enable ZoneAlarm Pro on the Router. This will require every PC to have ZoneAlarm Pro installed before being allowed to access the Internet (except for exempt computers). EtherFast® Cable/DSL Routers Help Enforcement Level This sets how often ZoneAlarm Pro will check for unauthorized intrusions. More Secure (default setting) enables ZoneAlarm Pro to check frequently.
Instant Broadband™ Series To upgrade the Router’s firmware: Note: By upgrading the Router’s firmware, you may lose the Router’s configuration settings. 1. Select the Help tab (see Figure 9-14). 2. Click Upgrade Firmware to display a new window (see Figure 9-15). Figure 9-15 3. Click the Browse button to find the firmware upgrade file that you downloaded from the Linksys website and then extracted. 4. Double-click the firmware file you downloaded and extracted.
Instant Broadband™ Series Blocking WAN Requests • By enabling the Block WAN Request feature, you can prevent your network from being “pinged,” or detected, by other Internet users. The Block WAN Request feature also reinforces your network security by hiding your network ports. Both functions of the Block WAN Request feature make it more difficult for outside users to work their way into your network. • Click the Apply button to save your changes.
Instant Broadband™ Series If you need to forward all ports to one PC, see the “DMZ” section. To add a server using Port Range Forwarding: 1. Enter the name of the application in the appropriate Customized Applications field. 2. Next to the name of the application, enter the number or range of the external port(s) used by the server or Internet application in the Ext. Port column. Check with the Internet application software documentation for more information. 3.
Instant Broadband™ Series • HTTP (HyperText Transport Protocol) The communications protocol used to connect to servers on the World Wide Web. Its primary function is to establish a connection with a web server and transmit HTML pages to the client web browser. • POP3 (Post Office Protocol 3) A standard mail server commonly used on the Internet. It provides a message store that holds incoming e-mail until users log on and download it. POP3 is a simple system with little selectivity.
Instant Broadband™ Series Dynamic Routing Figure 9-20 With Dynamic Routing (Figure 9-20) you can enable the Router to automatically adjust to physical changes in the network’s layout. The Router, using the RIP protocol, determines the network packets’ route based on the fewest number of hops between the source and the destination. The RIP protocol regularly broadcasts routing information to other routers on the network. To set up Dynamic Routing: 1. Choose the correct Working Mode.
Instant Broadband™ Series 2. Enter the following data to create a new static route. EtherFast® Cable/DSL Routers DMZ Host Destination LAN IP: The Destination LAN IP is the address of the remote network or host to which you want to assign a static route. Enter the IP address of the host for which you wish to create a static route here. If you are building a route to an entire network, be sure that the network portion of the IP address is set to 0. For example, the Router’s standard IP address is 192.168.1.
Instant Broadband™ Series EtherFast® Cable/DSL Routers Appendix A: Troubleshooting MAC Address Clone Common Problems and Solutions Note: This is a sample screen. Please enter the MAC Address for your Network Card/Adapter into this field. Figure 9-23 The Router’s MAC address is a 12-digit code assigned to a unique piece of hardware for identification, like a social security number.
Instant Broadband™ Series For Windows 2000: For Windows XP: A. Click Start, Settings, and Control Panel. Double-click Network and Dial-Up Connections. B. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using, and select the Properties option. C. In the Components checked are used by this connection box, highlight Internet Protocol (TCP/IP), and click the Properties button. Select Use the following IP address option. D.
Instant Broadband™ Series • Click the OK button in the Internet Protocol (TCP/IP) Properties window, and click the OK button in the Local Area Connection Properties window. • Restart the computer if asked. For Windows XP: The following instructions assume you are running Windows XP with the default interface. If you are using the Classic interface (where the icons and menus look like previous Windows versions), please follow the instructions for Windows 2000. • Click Start and Control Panel.
Instant Broadband™ Series F. Turn off the computer, Router, and cable/DSL modem. Wait 30 seconds, and then turn on the Router, cable/DSL modem, and computer. Check the Status tab of the Router’s web-based utility to see if you get an IP address. Your VPN may require port 500/UDP packets to be passed to the computer that is connecting to the IPSec server. Refer to “Problem #7, I need to set up online game hosting or use other Internet applications” for details. 4.
Instant Broadband™ Series 7. I need to set up online game hosting or use other Internet applications. If you want to play online games or use Internet applications, most will work without doing any port forwarding or DMZ hosting. There may be cases when you want to host an online game or Internet application. This would require you to set up the Router to deliver incoming packets or data to a specific computer. This also applies to the Internet applications you are using.
Instant Broadband™ Series 10. I am a PPPoE user, and I need to remove the proxy settings or the dial-up popup window. If you have proxy settings, you need to disable these on your computer. Because the Router is the gateway for the Internet connection, the computer does not need any proxy settings to gain access. Please follow these directions to verify that you do not have any proxy settings and that the browser you use is set to connect directly to the LAN. For Microsoft Internet Explorer 5.
Instant Broadband™ Series 15. I can't access my email, web, or VPN, or I am getting corrupted data from the Internet. The Maximum Transmission Unit (MTU) setting may need to be adjusted. By default, the MTU is set at 1500. For most DSL users, it is strongly recommended to use MTU 1492. If you are having some difficulties, perform the following steps: A. To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the Router. B. Enter the password, if asked.
Instant Broadband™ Series Frequently Asked Questions What is the maximum number of IP addresses that the Router will support? The Router will support up to 253 IP addresses. Is IPSec Pass-Through supported by the Router? Yes, it is a built-in feature that the Router automatically enables. Where is the Router installed on the network? In a typical environment, the Router is installed between the cable/DSL modem and the LAN. Plug the Router into the cable/DSL modem’s Ethernet port.
Instant Broadband™ Series EtherFast® Cable/DSL Routers If all else fails in the installation, what can I do? Reset the Router by holding down the reset button until the Diag LED fully turns on and off. Reset your cable or DSL modem by powering the unit off and then on. Obtain and flash the latest firmware release that is readily available on the Linksys website, www.linksys.com. Does the Router pass PPTP packets or actively route PPTP sessions? The Router allows PPTP packets to pass through.
Instant Broadband™ Series Appendix B: Glossary Bridge - A device that interconnects different networks together. 10BaseT - An Ethernet standard that uses twisted wire pairs. Broadband - A data-transmission scheme in which multiple signals share the bandwidth of a medium. This allows the transmission of voice, data, and video signals over a single medium. Cable television uses broadband techniques to deliver dozens of channels over one cable.
Instant Broadband™ Series CPU (Central Processing Unit) - The computing part of the computer. Also called the “processor,” it is made up of the control unit and ALU. DHCP supports static addresses for computers containing Web servers that need a permanent IP address. CSMA/CD (Carrier Sense Multiple Access/Collision Detection) - The LAN access method used in Ethernet. When a device wants to gain access to the network, it checks to see if the network is quiet (senses the carrier).
Instant Broadband™ Series Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium. Has a transfer rate of 10 Mbps. Forms the underlying transport vehicle used by several upper-level protocols, including TCP/IP and XNS. Fast Ethernet - A 100 Mbps technology based on the 10Base-T Ethernet CSMA/CD network access method. Full Duplex - The ability of a device or line to transmit data simultaneously in both directions.
Instant Broadband™ Series IPCONFIG - A utility that provides for querying, defining and managing IP addresses within a network. A commonly used utility, under Windows NT and 2000, for configuring networks with static IP addresses. IPSec - IPSec (Internet Protocol Security) is a developing standard for security at the network or packet processing layer of network communication. A big advantage of IPSec is that security arrangements can be handled without requiring changes to individual user computers.
Instant Broadband™ Series Partitioning - To divide a resource or application into smaller pieces. PCI (Peripheral Component Interconnect) - A peripheral bus commonly used in PCs, Macintoshes and workstations. It was designed primarily by Intel and first appeared on PCs in late 1993. PCI provides a high-speed data path between the CPU and peripheral devices (video, disk, network, etc.). There are typically three or four PCI slots on the motherboard.
Instant Broadband™ Series Software - Instructions for the computer. A series of instructions that performs a particular task is called a “program.” The two major categories of software are “system software” and “application software.” System software is made up of control programs such as the operating system and database management system (DBMS). Application software is any program that processes data for the user.
Instant Broadband™ Series URL (Uniform Resource Locator) - The address that defines the route to a file on the Web or any other Internet facility. URLs are typed into the browser to access Web pages, and URLs are embedded within the pages themselves to provide the hypertext links to other pages. UTP - Unshielded twisted pair is the most common kind of copper telephone wiring. Twisted pair is the ordinary copper wire that connects home and many business computers to the telephone company.
Instant Broadband™ Series EtherFast® Cable/DSL Routers Step One: Pinging an IP Address Step Two: Pinging for a Web Address The first step to determining your ISP’s web and e-mail server address is to ping its IP address. While the IP address returned above would work as your e-mail server address, it may not be permanent. IP addresses change all the time. Web addresses, however, usually don’t.
Instant Broadband™ Series Appendix D: Installing the TCP/IP Protocol EtherFast® Cable/DSL Routers 6. Find and double-click TCP/IP in the list to the right (see Figure D-2). Follow these instructions to install the TCP/IP protocol on one of your PCs only after a network card has been successfully installed inside the PC. These instructions are for Windows 95, Windows 98, and Windows Me. For TCP/IP setup under Windows NT, 2000, and XP, see your Windows documentation or the Help feature. 1.
Instant Broadband™ Series Appendix E: Twisted-Pair Cabling There are different grades, or “categories,” of twisted-pair cabling. Category 5 is the most reliable and most highly recommended. Category 3 is a good second choice. Straight-through cables are used for connecting computers to a hub.
Instant Broadband™ Series Appendix F: Finding the MAC Address and IP Address for Your Ethernet Adapter EtherFast® Cable/DSL Routers 3. Write down the Adapter Address as shown on your computer screen (see Figure F-3). This is the MAC address for your Ethernet adapter and will be shown as a series of numbers and letters. The MAC address/Adapter Address is what you will use for MAC Address Cloning or MAC Filtering.
Instant Broadband™ Series 2. In the command prompt, enter ipconfig /all. Then press the Enter key. EtherFast® Cable/DSL Routers When entering the information using the Router’s web-based utility, you will type the 12-digit MAC address in this format, XXXXXXXXXXXX without the hyphens for MAC Filtering. See Figure F-6. Figure F-5 Figure F-6 3. Write down the Physical Address as shown on your computer screen (Figure F-5); it is the MAC address for your Ethernet adapter.
Instant Broadband™ Series Appendix G: Setting Up AOL® Broadband Cable & DSL This document provides instructions for setting up the Router using firmware version 1.43 or above to work with AOL Broadband via a Cable or DSL connection. This Router's AOL Parental Controls feature is available for AOL customers in the US only. Please follow the instructions in the appropriate section below to configure for AOL Broadband for the type of broadband connection you have. Note: You must install AOL 7.
Instant Broadband™ Series Appendix H: 4-Port Router Specifications AOL Broadband via DSL 1. Open your web browser. Enter http://192.168.1.1 in the web browser’s Address field, as shown in Figure G-5, and press the Enter key. 2. A password request page, shown in Figure G-6 will appear. (Windows XP users will see a Connect to 192.168.1.1 window slightly different from that shown). Leave the User Name field blank, and enter admin in the Password field. Then click the OK button.
Instant Broadband™ Series Appendix I: 1-Port Router Specifications Appendix J: 3-Port Router Specifications 1-Port Router Specifications Model Number Standards Model Number Standards Protocol Ports LAN: WAN: Speed WAN: LAN: Cabling Type 10BaseT: 100BaseTX: Topology LED Indicators LAN: WAN: BEFSR11, ver. 2 IEEE 802.3 (10BaseT), IEEE 802.
Instant Broadband™ Series Appendix K: Warranty Information BE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODE FROM THE PRODUCT'S PACKAGING ON HAND WHEN CALLING. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. IN NO EVENT SHALL LINKSYS’S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS DOCUMENTATION. LINKSYS DOES NOT OFFER REFUNDS FOR ANY PRODUCT.
www.linksys.com © Copyright 2002 Linksys, All Rights Reserved.
