USER GUIDE Wireless-G Access Point with Power Over Ethernet and Rangebooster Model No.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Copyright and Trademarks Specifications are subject to change without notice. Linksys, Cisco and the Cisco Logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2008 Cisco Systems, Inc. All rights reserved.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Table of Contents Chapter 1: Introduction Welcome What’s in this User Guide? 1 1 2 Chapter 2: Planning Your Wireless Network 4 Network Topology Roaming Network Layout Example of a simple wireless network 4 4 5 6 Chapter 3: Getting to Know the Wireless-G Access Point The LEDs The Ports Antennas and Positions Chapter 4: Connecting the Wireless-G Access Point Overview Connection Placement Options Chapter 5: Setting Up the Wireless-G Acc
Wireless-G Access Point with Power Over Ethernet and Rangebooster The Administration - Log Tab The Administration - Factory Default Tab The Administration - Firmware Upgrade Tab The Administration - Reboot Tab The Administration - Config Management Tab The Status - Local Network Tab The Status - Wireless Tab The Status - System Performance Tab 36 37 37 38 38 39 40 41 Appendix A: Troubleshooting 43 Frequently Asked Questions 43 Appendix B: Wireless Security Security Precautions Security Threats Facing
Wireless-G Access Point with Power Over Ethernet and Rangebooster List of Figures Figure 2-1: Example of a Simple Wireless Network Figure 3-1: Front Panel Figure 3-2: Back View Figure 3-3: Desktop Placement and Antenna Setup Figure 4-1: Connect the Ethernet Cable Figure 4-2: Connect the Power Figure 4-3: Stand Figure 4-4: Mounting Dimensions Figure 5-1: Login Screen Figure 6-1: Setup - Basic Setup Figure 6-2: Setup - Time Figure 6-3: Wireless - Basic Wireless Settings Figure 6-4: Wireless - Wireless Securi
Wireless-G Access Point with Power Over Ethernet and Rangebooster Figure 6-20: Security Monitor - Basic Settings Figure 6-21: Security Monitor - Event Log Figure 6-22: Administration - Management Figure 6-23: Administration - Log Figure 6-24: Administration - Factory Default Figure 6-25: Administration - Firmware Upgrade Figure 6-26: Administration - Reboot Figure 6-27: Administration - Config Management Figure 6-28: Status - Local Network Figure 6-29: Status - Wireless Figure 6-30: Status - System Perform
Wireless-G Access Point with Power Over Ethernet and Rangebooster Chapter 1: Introduction Welcome Thank you for choosing the Wireless-G Access Point with Power Over Ethernet and Rangebooster. This Access Point will allow you to network wirelessly better than ever. How does the Access Point do all of this? An access point allows for greater range and mobility within your wireless network while also allowing you to connect the wireless network to a wired environment.
Wireless-G Access Point with Power Over Ethernet and Rangebooster What’s in this User Guide? This user guide covers the steps for setting up and using the Wireless-G Access Point. • Chapter 1: Introduction This chapter describes the Wireless-G Access Point’s applications and this User Guide. • Chapter 2: Planning your Wireless Network This chapter describes the basics of wireless networking.
Wireless-G Access Point with Power Over Ethernet and Rangebooster • Appendix G: Warranty Information This appendix supplies the Access Point’s warranty information. • Appendix H: Regulatory Information This appendix supplies the Access Point’s regulatory information. • Appendix I: Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Chapter 2: Planning Your Wireless Network Network Topology A wireless network is a group of computers, each equipped with one or more wireless adapters. Computers in a wireless network must be configured to share the same radio channel to talk to each other. Several PCs equipped with wireless cards or adapters can communicate with each other to form an ad-hoc network without the use of an access point.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Network Layout The Wireless-G Access Point with Power Over Ethernet and Rangebooster has been designed for use with 802.11g and 802.11b products. The Access Point is compatible with 802.11g and 802.11b adapters, such as the notebook adapters for your laptop computers, PCI adapters for your desktop PCs, and USB adapters for all PCs when you want to enjoy wireless connectivity. These wireless products can also communicate with an 802.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Example of a simple wireless network Figure 2-1: Example of a Simple Wireless Network The above diagram shows a typical infrastructure wireless network setup. The wireless Access Points are connecting to a Linksys switch that provides power to the Access Points. Each Access Point can connect multiple wireless devices to the network.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Chapter 3: Getting to Know the Wireless-G Access Point The LEDs The Access Point's LEDs, where information about network activity is displayed, are located on the front panel. Figure 3-1: Front Panel Power Green. The Power LED lights up when the Access Point is powered on. PoE Green. The PoE LED lights up when the Access Point is powered through Ethernet cable. WIRELESS Green.
Wireless-G Access Point with Power Over Ethernet and Rangebooster The Ports The Access Point’s port are located on the back of the device. port: the connection point on a computer or networking device used for plugging in cables or adapters Figure 3-2: Back View Reset Button There are two ways to reset the Access Point to the factory default configuration. Either press the Reset button, for approximately ten seconds, or restore the defaults using the Access Point's web-based utility.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Antennas and Positions The Access Point’s antennas are located on the back of the device. The Access Point can be placed on a desktop or wall-mounted. When placed on a desktop, the Access Point can be stacked with other Linksys Business Series products. Antenna The Access Point has two detachable 2dBi omni-directional antennas. Adjust the two antennas so that they form a 90 degree angle for best MIMO range performance.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Chapter 4: Connecting the Wireless-G Access Point Overview This chapter explains how to place and connect the Access Point. hardware: the physical aspect of computers, telecommunications, and other information technology devices. Depending on your application, you might want to set up the device first before mounting the device. Refer to “Chapter 5: Setting Up the Wireless-G Access Point”. Connection 1.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Placement Options There are three ways to place the Wireless-G Access Point. The first way is to place it horizontally on a surface, so it sits on its four rubber feet. The second way is to stand the Access Point vertically on a surface. The third way is to mount it on a wall. The stand and wall-mount options are explained in further detail below. Stand Option Large Prongs 1. Locate the Access Point’s left side panel. 2.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Chapter 5: Setting Up the Wireless-G Access Point Overview The Access Point has been designed to be functional right out of the box with the default settings. However, if you'd like to change these settings, the Access Point can be configured through your web browser with the web-based Utility. This chapter explains how to use the Utility to perform the most basic settings.
Wireless-G Access Point with Power Over Ethernet and Rangebooster 3. Although it is not recommended, you can connect your PC wirelessly to the Access Point when the DHCP server is connected on the LAN side. It is not recommended, because you can easily lose your connection through configuration changes. Launch your web browser, such as Internet Explorer or Mozilla Firefox and enter the Access Point’s default IP address, 192.168.1.245, in the Address field. Press the Enter key.
Wireless-G Access Point with Power Over Ethernet and Rangebooster • Advanced Wireless Settings. Use this screen to configure the Access Point’s more advanced wireless settings. • VLAN & QoS. Use this screen to configure VLAN and QoS settings. AP Mode Use this screen to configure the Access Point mode. The three available modes are Access Point, Wireless Repeater, and Wireless Bridge. snmp: the standard network management protocol on the Internet. Security Monitor • Basic Settings.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Status You will be able to view status information for your local network, wireless networks, and network performance. • Local Network. This screen displays system information, including software & hardware version, MAC address, and IP address on the LAN side of the Access Point. • Wireless. This screen displays wireless network settings including SSID, network mode, and wireless channel. • System Performance.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Chapter 6: Configuring the Wireless-G Access Point This chapter is a detailed reference guide for the web-based utility. You do not need the Utility to start using your Access Point. The Access Point has been designed to be functional right out of the box with the default settings.
Wireless-G Access Point with Power Over Ethernet and Rangebooster • Subnet Mask. The Subnet Mask must be the same as that set on the LAN that your Access Point is connected to. The default is 255.255.255.0. • Default Gateway. Your ISP will provide you with the Default Gateway Address, which is the ISP server’s IP address. • Primary DNS (Required) and Secondary DNS (Optional). Your ISP will provide you with at least one DNS (Domain Name System) Server IP Address.
Wireless-G Access Point with Power Over Ethernet and Rangebooster The Wireless - Basic Wireless Settings Tab Change the basic wireless network settings on this screen. The Access Point can connect to up to four wireless networks (SSIDs) at the same time, so this screen offers settings for up to four different SSIDs. Each SSID owns its own MAC address on this Access Point. Basic Settings Configure the Wireless Network basic attributes for the entire system and for each SSID. Wireless Network Mode.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Change these settings as described here and click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. Help information is available on the right side of the screen. The Wireless - Wireless Security Tab Change the Access Point’s wireless security settings on this screen. Wireless Security Select SSID. Select any of the SSID names configured on the Basic Wireless Settings tab.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Default Transmit Key. Select the key to be used for data encryption. WEP Encryption. Select a level of WEP encryption, 64 bits (10 hex digits) or 128 bits (26 hex digits). Passphrase. If you want to generate WEP keys using a Passphrase, then enter the Passphrase in the field provided and click the Generate key. Those auto-generated keys are not as strong as manual WEP keys. Key 1-4.
Wireless-G Access Point with Power Over Ethernet and Rangebooster WPA2-Personal Mixed This security mode supports the transition from WPA-Personal to WPA2-Personal. You can have client devices that use either WPA-Personal or WPA2-Personal. The Access Point will automatically choose the encryption algorithm used by each client device. WPA Algorithm. Mixed Mode automatically chooses TKIP or AES for data encryption. WPA Shared Key. Enter a WPA Shared Key of 8-63 characters. Key Renewal Timeout.
Wireless-G Access Point with Power Over Ethernet and Rangebooster WPA2-Enterprise This option features WPA2 used in coordination with a RADIUS server for client authentication. (This should only be used when a RADIUS server is connected to the Access Point.) RADIUS Server IP Address. Enter the RADIUS server’s IP address. RADIUS Server Port. Enter the port number used by the RADIUS server. The default is 1812. WPA Algorithm. WPA2 always uses AES for data encryption. Shared Secret.
Wireless-G Access Point with Power Over Ethernet and Rangebooster RADIUS This security mode is also known as Dynamic WEP with IEEE 802.1X. A RADIUS server is used for client authentication and WEP is used for data encryption. The WEP key is automatically generated by the RADIUS server. Manual WEP key is no longer supported to ensure compatibility with Microsoft’s Windows implementation. RADIUS Server IP Address. Enter the RADIUS server’s IP address. RADIUS Server Port.
Wireless-G Access Point with Power Over Ethernet and Rangebooster The Wireless - Wireless Connection Control Tab This screen allows you to configure the Connection Control List to either permit or block specific wireless client devices connecting to (associating with) the Access Point. Wireless Connection Control Select SSID. Select the SSID of the wireless network that you want to use wireless connection control on. Enabled/Disabled. Enable or disable wireless connection control. The default is disabled.
Wireless-G Access Point with Power Over Ethernet and Rangebooster The Wireless - Advanced Wireless Settings Tab This screen allows you to configure the advanced settings for the Access Point. Linksys recommends to let your Access Point automatically adjust the parameters for maximum data throughput. Advanced Settings CTS Protection Mode. CTS (Clear-To-Send) Protection Mode function boosts the Access Point’s ability to catch all wireless transmissions, but will severely decrease performance.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Fragmentation Threshold. This specifies the maximum size a data packet can be before splitting and creating a new packet. It should remain at its default setting of 2346. A smaller setting means smaller packets, which will create more packets for each transmission. If you experience high packet error rates, you can decrease this value, but it will likely decrease overall network performance.
Wireless-G Access Point with Power Over Ethernet and Rangebooster QoS The following options are VLAN global settings for the Access Point. Default CoS (Priority). Select Enabled if you want to assign a default CoS value to each SSID. This option is automatically enabled when the VLAN option is enabled. The default is Disabled. U-APSD (Unscheduled Automatic Power Save Delivery). This option is only available when WMM is enabled on any of the SSIDs.
Wireless-G Access Point with Power Over Ethernet and Rangebooster The AP Mode Tab On this screen you can change the Access Point’s mode of operation. In most cases, you can keep the default setting - Access Point. You may wish to change the Access Point’s mode of operation if you want to use the Access Point as a wireless repeater to extend the range of your wireless network.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Wireless Repeater. When set to Wireless Repeater mode, the Wireless Repeater is able to talk to up a remote access point within its range and retransmit its signal. Click Site Survey to select the access point that will have its signal repeated by this Access Point or enter the MAC address of the access point manually.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Wireless Bridge. This mode connects physically separated wired networks using multiple access points. Wireless clients will not be able to connect to the access point in this mode. Enter the MAC address(es) of the access point(s) that will bridge to this access point. IMPORTANT: In Wireless Bridge mode, the Access Point can ONLY be accessed by another access point set to Wireless Bridge mode.
Wireless-G Access Point with Power Over Ethernet and Rangebooster The Security Monitor - Basic Settings Tab On this screen you can enable or disable the security monitor feature of this Wireless Access Point. It also allows you to create user accounts for system administrators to use this advanced feature. This feature works together with Linksys Business Series wireless client adapters.
Wireless-G Access Point with Power Over Ethernet and Rangebooster The Security Monitor - Event Log Tab Configure the event logging options for security monitor. E-mail Notification Recipient To. Enter the e-mail address that the alarm notifications should be sent to. Alarm Type. Select the type of intrusions that should require an e-mail notification. • Rogue AP Detected. Indicates a rogue access point has been detected. • AP SSID Changed. Indicates the Access Point’s SSID has been changed.
Wireless-G Access Point with Power Over Ethernet and Rangebooster • Duplicate SSID in use. Indicates an unauthorized AP has the same SSID value as an authorized AP. SYSLOG Notification Logviewer IP Address. Enter the IP address of the system that will store the system log. Alarm Type. Select the type of intrusions that should require an e-mail notification. • Rogue AP Detected. Indicates a rogue access point has been detected. • AP SSID Changed. Indicates the Access Point’s SSID has been changed.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Security Monitor Server This is a special Syslog server that can record all security monitor events instead of selected events. Server IP Address. Enter the IP address of the server. The Administration - Management Tab On this screen you can configure the password, Web Access, and SNMP settings. Management You should change the username/password that controls access to the Access Point’s web-based utility to prevent unauthorized access.
Wireless-G Access Point with Power Over Ethernet and Rangebooster SNMP SNMP is a popular network monitoring and management protocol. It provides network administrators with the ability to monitor the status of the Access Point and receive notification of any critical events as they occur on the Access Point. To enable the SNMP support feature, select Enabled. Otherwise, select Disabled. The default is Disabled. This Access Point supports SNMP version 1, 2, and 3.
Wireless-G Access Point with Power Over Ethernet and Rangebooster The Administration - Log Tab On this screen you can configure the log settings and alerts of particular events. Log You can have logs that keep track of the Access Point’s activities. Email Alert E-Mail Alert. If you want the Access Point to send e-mail alerts in the event of certain attacks, select Enabled. The default is Disabled. E-Mail Address for Logs. Enter the e-mail address that will receive logs.
Wireless-G Access Point with Power Over Ethernet and Rangebooster System Error Messages. If you want to log system error messages, click the checkbox. Configuration Changes. If you want to log any configuration changes, click the checkbox. Change these settings as described here and click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. Help information is available on the right side of the screen.
Wireless-G Access Point with Power Over Ethernet and Rangebooster 3. On the Firmware Upgrade screen, enter the location of the firmware upgrade file in the field provided, or click the Browse button to find the file. 4. Click the Upgrade button, and follow the on-screen instructions. Help information is available on the right side of the screen. The Administration - Reboot Tab On this screen you can reboot the Access Point. Reboot This feature is useful when you need to remotely reboot the Access Point.
Wireless-G Access Point with Power Over Ethernet and Rangebooster The Status - Local Network Tab The Local Network screen displays the Access Point’s current status information for the local network. Information Hardware Version. This is the version of the Access Point’s current hardware. Software Version. This is the version of the Access Point’s current software. Local MAC Address. The MAC address of the Access Point’s Local Area Network (LAN) interface is displayed here. System Up Time.
Wireless-G Access Point with Power Over Ethernet and Rangebooster The Status - Wireless Tab The Wireless screen displays the Access Point’s current status information for the wireless network(s). Wireless Network MAC Address. The MAC Address of the Access Point’s wireless interface is displayed here. Mode. The Access Point’s wireless network mode is displayed here. SSID 1-4. The Access Point’s SSIDs that have been configured are displayed here. Channel.
Wireless-G Access Point with Power Over Ethernet and Rangebooster The Status - System Performance Tab The System Performance screen displays the Access Point’s status information for its current settings and data transmissions. System Performance Wired Name. This indicates that the statistics are for the wired network, the LAN. IP Address. The Access Point’s local IP address is displayed here. MAC Address. This shows the MAC Address of the Access Point’s wired interface. Connection.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Bytes Received. This shows the number of bytes received for each wireless network. Bytes Sent. This shows the number of bytes sent for each wireless network. Error Packets Received. This shows the number of error packets received for each wireless network. Drop Received Packets. This shows the number of packets being dropped after they were received. To update the status information, click the Refresh button.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Appendix A: Troubleshooting This appendix provides solutions to problems that may occur during the installation and operation of the Wireless-G Access Point with Power Over Ethernet. Read the descriptions below to help solve your problems. If you can't find an answer here, check the Linksys website at www.linksys.com. Frequently Asked Questions Can the Access Point act as my DHCP Server? No.
Wireless-G Access Point with Power Over Ethernet and Rangebooster What IEEE 802.11g features are supported? The product supports the following IEEE 802.11g functions: • CSMA/CA plus Acknowledge protocol • OFDM protocol • Multi-Channel Roaming • Automatic Rate Selection • RTS/CTS feature • Fragmentation • Power Management What is Ad-hoc? An Ad-hoc wireless LAN is a group of computers, each with a WLAN adapter, connected as an independent wireless LAN.
Wireless-G Access Point with Power Over Ethernet and Rangebooster What is the ISM band? The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM (Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide. This presents a truly revolutionary opportunity to place convenient high speed wireless capabilities in the hands of users around the globe.
Wireless-G Access Point with Power Over Ethernet and Rangebooster What is a MAC Address? The Media Access Control (MAC) address is a unique number assigned by the manufacturer to any Ethernet networking device, such as a network adapter, that allows the network to identify it at the hardware level. For all practical purposes, this number is usually permanent.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Appendix B: Wireless Security Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation. So, keep the following in mind whenever you are setting up or using your wireless network.
Wireless-G Access Point with Power Over Ethernet and Rangebooster SSID. There are several things to keep in mind about the SSID: 1. Disable Broadcast 2. Make it unique 3. Change it often Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast the SSID. Wireless networking products come with a default SSID set by the factory.
Wireless-G Access Point with Power Over Ethernet and Rangebooster WPA Personal. If you do not have a RADIUS server, select the type of algorithm, TKIP or AES, enter a password in the Pre-Shared key field of 8-63 characters, and enter a Group Key Renewal period time between 0 and 99,999 seconds, which instructs the AP or other device how often it should change the encryption keys. WPA Enterprise. WPA used in coordination with a RADIUS server.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Appendix C: Upgrading Firmware The Access Point's firmware is upgraded through the web-based utility’s Administration - Firmware Upgrade tab. Follow these instructions: 1. Download the firmware upgrade file from the Linksys website, www.linksys.com. 2. Extract the firmware upgrade file on your computer. 3. Open the Access Point’s web-based utility. 4. Click the Administration tab. 5. Click the Upgrade Firmware tab. 6.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Appendix D: Windows Help Almost all wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix. TCP/IP Before a computer can communicate with the Access Point, TCP/IP must be enabled.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Appendix E: Glossary This glossary contains some basic networking terms you may come across when using this product. For more advanced terms, see the complete Linksys glossary at http://www.linksys.com/glossary. Access Point - A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network.
Wireless-G Access Point with Power Over Ethernet and Rangebooster DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be “seen” from the Internet. DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP addresses. Domain - A specific name for a network of computers. Download - To receive a file transmitted over a network.
Wireless-G Access Point with Power Over Ethernet and Rangebooster IP Address - The address used to identify a computer or device on a network. IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device. IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer. ISP (Internet Service Provider) - A company that provides access to the Internet.
Wireless-G Access Point with Power Over Ethernet and Rangebooster RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires. Roaming - The ability to take a wireless device from one access point's range to another without losing the connection. Router - A networking device that connects multiple networks together. Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services.
Wireless-G Access Point with Power Over Ethernet and Rangebooster TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted. Topology - The physical layout of a network. TX Rate - Transmission Rate. Upgrade - To replace existing software or firmware with a newer version. Upload - To transmit a file over a network. URL (Uniform Resource Locator) - The address of a file located on the Internet.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Appendix F: Specifications Model WAP200 Standards IEEE802.11g, IEEE802.11b, IEEE802.3, IEEE802.3u, IEEE802.3af (Power Over Ethernet), 802.1p (QoS priority), 802.1q (VLAN), 802.1X (Security Authentication), 802.11i - Ready (Security WPA2), 802.11e - Ready (Wireless QoS), 802.
Wireless-G Access Point with Power Over Ethernet and Rangebooster DHCP DHCP Client Operating Modes Access Point Access Point Mode, point-to-point Bridge Mode, point-to-multipoint Bridge Mode, Repeater Mode Wireless Spec/Modulation Radio and Modulation Type: 802.11b/DSSS, 11g/OFDM Channels Operating Channels: 11 North America, 13 Most of Europe (ETSI and Japan) # of Internal Ant. None # of External Ant.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Wireless Security Monitor Scan and Classify wireless devices in the network. Reports new clients and APs joining the network and suspicious network events. (working together with 200 Business series client cards) Quality of Service QoS 4 queues WMM Wireless priority General Wireless roaming based on IAPP Auto-channel selection Device Dimensions 6.69" x 8.07" x 7.68" (170 x 205 x 195mm) Weight 0.88 lb (0.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Appendix G: Warranty Information LIMITED WARRANTY Linksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Appendix H: Regulatory Information FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Industry Canada Statement This device complies with Industry Canada ICES-003 and RSS210 rules. Déclaration d’Industrie Canada Cet appareil est conforme aux normes NMB003 et RSS210 d'Industrie Canada. Industry Canada Statement Operation is subject to the following two conditions: 1. This device may not cause interference and 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Wireless-G Access Point with Power Over Ethernet and Rangebooster User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) This document contains important information for users with regards to the proper disposal and recycling of Linksys products.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Appendix H: Regulatory Information 64
Wireless-G Access Point with Power Over Ethernet and Rangebooster Appendix H: Regulatory Information 65
Wireless-G Access Point with Power Over Ethernet and Rangebooster Appendix H: Regulatory Information 66
Wireless-G Access Point with Power Over Ethernet and Rangebooster For more information, visit www.linksys.com.
Wireless-G Access Point with Power Over Ethernet and Rangebooster Appendix I: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com or ftp.linksys.
