® A Division of Cisco Systems, Inc. 2.4 GHz Wireless-G 802.11g Access Point WIRELESS Model No.
Wireless-G Access Point Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2004 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.
Wireless-G Access Point Table of Contents Chapter 1: Introduction 1 Welcome What’s in this Guide? 1 2 Chapter 2: Planning your Wireless Network Network Topology Roaming Network Layout Chapter 3: Getting to Know the Wireless-G Access Point The Back Panel The Front Panel Chapter 4: Connecting the Wireless-G Access Point Hardware Installation Chapter 5: Setting Up the Wireless-G Access Point 4 4 4 5 6 6 7 8 8 9 Setup Wizard Linksys Wireless Guard Setup 9 15 Chapter 6: Linksys Wireless Guard 18
Wireless-G Access Point Appendix C: Upgrading Firmware Appendix D: Windows Help Appendix E: Glossary Appendix F: Specifications Appendix G: Warranty Information Appendix H: Regulatory Information Appendix I: Contact Information 53 54 55 59 61 62 64
Wireless-G Access Point List of Figures Figure 3-1: The Access Point’s Back Panel Figure 3-2: Front Panel Figure 5-1: The Setup Wizard’s Welcome Screen Figure 5-2: Connecting the Access Point Figure 5-3: Select an Access Point Figure 5-4: Enter the Password Figure 5-5: The Configure Network Address Settings Screen Figure 5-6: The Wireless Settings Screen Figure 5-7: The Security Settings Screen Figure 5-8: The WEP Settings Screen Figure 5-9: The WPA-PSK Screen Figure 5-10: The Congratulations Screen Figure
Wireless-G Access Point Figure 6-11: Network Administration Figure 6-12: Modify Access Control Figure 6-13: Add Guest Figure 6-14: Add Member Figure 6-15: Welcome Figure 6-16: Subscriber Information Figure 6-17: Account Finances Figure 6-18: Credentials Information Figure 6-19: Congratulations Figure 7-1: Password Screen Figure 7-2: The Basic Setup Screen Figure 7-3: WPA Pre-Shared Key Settings Figure 7-4: WPA Radius Settings Figure 7-5: Radius Settings Figure 7-6: WEP Settings Figure 7-7: The Password Scr
Wireless-G Access Point Chapter 1: Introduction Welcome Thank you for choosing the Wireless-G Access Point. This Access Point will allow you to network wirelessly better than ever. network: a series of computers or devices connected together How does the Access Point do all of this? An access point allows for greater range and mobility within your wireless network while also allowing you to connect the wireless network to a wired environment.
Wireless-G Access Point What’s in this Guide? This user guide covers the steps for setting up and using the Wireless-G Access Point. • Chapter 1: Introduction This chapter describes the Wireless-G Access Point’s applications and this User Guide. • Chapter 2: Planning your Wireless Network This chapter describes the basics of wireless networking. • Chapter 3: Getting to Know the Wireless-G Access Point This chapter describes the physical features of the Access Point.
Wireless-G Access Point • Appendix F: Specifications This appendix provides the Access Point’s technical specifications. • Appendix G: Warranty Information This appendix supplies the Access Point’s warranty information. • Appendix H: Regulatory Information This appendix supplies the Access Point’s regulatory information. • Appendix I: Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support.
Wireless-G Access Point Chapter 2: Planning your Wireless Network Network Topology A wireless network is a group of computers, each equipped with one wireless adapter. Computers in a wireless network must be configured to share the same radio channel. Several PCs equipped with wireless cards or adapters can communicate with one another to form an ad-hoc network.
Wireless-G Access Point Network Layout The Wireless-G Access Point has been designed for use with 802.11g and 802.11b products. With 802.11g products communicating with the 802.11b standard, products using these standards can communicate with each other. The Access point is compatible with 802.11g and 802.11b adapters, such at the PC Cards for your laptop computers, PCI Card for your desktop PC, and USB Adapters for when you want to enjoy USB connectivity.
Wireless-G Access Point Chapter 3: Getting to Know the Wireless-G Access Point The Back Panel The Access Point's ports, where the power cord and network cable are connected, are located on the back panel. Figure 3-1: The Access Point’s Back Panel LAN This LAN (Local Area Network) port connects to Ethernet network devices, such as a switch or router. Power The Power port is where you will connect the power adapter. Reset Button There are two ways to Reset the Access Point's factory defaults.
Wireless-G Access Point The Front Panel The Access Point's LEDs, where information about network activity is displayed, are located on the front panel. Figure 3-2: Front Panel Power Green. The Power LED lights up when the Access Point is powered on. Act Green. If the Act LED is flickering, the Access Point is actively sending or receiving data to or from one of the devices over the LAN port. Link Green.
Wireless-G Access Point Chapter 4: Connecting the Wireless-G Access Point Hardware Installation 1. Locate an optimum location for the Access Point. The best place for the Access Point is usually at the center of your wireless network, with line of sight to all of your PCs and wireless accessories. 2. Fix the direction of the antenna. Try to place it in a position that will best cover your wireless network. Normally, the higher you place the antenna, the better the performance will be.
Wireless-G Access Point Chapter 5: Setting Up the Wireless-G Access Point Setup Wizard Now that you've connected the Access Point to your wired network, you are ready to begin setting it up. This Setup Wizard will take you through all the steps necessary to configure the Access Point. 1. Insert the Setup Wizard CD into your PC's CD-ROM drive. Your PC must be on your wired network to set up the Access Point.
Wireless-G Access Point 3. The next screen displayed displays how the Access Point should be connected while running this Setup Wizard. Optimally, you should perform this setup through a PC on your wired network. Click the Next button to continue or Exit to exit the Setup Wizard. Figure 5-2: Connecting the Access Point 4. The Setup Wizard will run a search for the Access Point within your network and then display a list along with the status information for each access point.
Wireless-G Access Point 5. You will be asked to sign onto the Access Point you've selected. Enter the Password you've assigned. If none has been assigned, enter the default password: admin. Then, click the OK button. (This password can be changed from the Web-based Utility's Password tab.) Figure 5-4: Enter the Password ip (internet protocol): a protocol used to send data over a network 6. The Configure Network Address Settings screen will appear next.
Wireless-G Access Point 7. The Wireless Settings screen should now appear. Enter your wireless network's SSID and select the channel at which the network broadcasts its wireless signal. Also enter a Device Name to prevent any confusion when using multiple Access Points. Then, click the Next button to continue or Back to return to the previous page. • SSID. The SSID is the unique name shared among all points in a wireless network. The SSID must be identical for all points in the wireless network.
Wireless-G Access Point • WEP. From this screen, you can set the level of encryption you desire for your network, along with selecting Passphrases and/or encryption keys. The WEP key can consist of the letters "A" through "F" and the numbers "0" through "9" and should be 10 characters in length for 64-bit encryption or 26 characters in length for 128-bit encryption. Figure 5-8: The WEP Settings Screen bit: a binary digit • WPA Personal.
Wireless-G Access Point 9. At this point, the configuration performed with the Setup Wizard is complete. To configure any other Access Points in your network, you can run this Setup Wizard again. Click the Exit button to exit the Setup Wizard. For more advanced configuration, you can go to Chapter 7: Configuring the Wireless-G Access Point.
Wireless-G Access Point Linksys Wireless Guard Setup Linksys Wireless Guard is a subscription service that gives you WPA RADIUS without having to build your own RADIUS network. Follow the instructions below. To learn more about Linksys Wireless Guard, go to www.linksys.com/wirelessguard. If you need help with setting up Linksys Wireless Guard, contact us at wirelessguard@linksys.com or call 888-231-5506. 1. After clicking on Linksy Wireless Guard for your security selection, this screen will appear.
Wireless-G Access Point 3. When the next screen appears, your Access Point will be automatically configured. Make sure that the correct access point is selected and that the name is correct. Also, make sure that the SSID is correct. Click Next to add this Access Point to your network or click Back to return to the previous screen. Figure 5-13: The Securing your Access Point Screen 4. For security reasons, the password has been automatically changed.
Wireless-G Access Point 5. When the next screen appears, you will specify which users you will allow access to this protected network. Enter the E-mail address, User Name, Password, then Confirm Password for each user. Then, click Add. To remove a user from the list, select the user, then click Remove. Figure 5-15: The Adding Authorized Users Screen 6. The Access Point is now configured for Linksys Wireless Guard.
Wireless-G Access Point Chapter 6: Linksys Wireless Guard This chapter is only for users who have signed up for Linksys Wireless Guard to secure their network and have configured the Access Point for Linksys Wireless Guard. (Refer to Chapter 5: Setting up the Wireless-G Access Point.) You will now need to install the client software needed to securely connect a PC to your Access Point that is protected by Linksys Wireless Guard.
Wireless-G Access Point 3. The next screen informs you to close all other applications before continuing. If no other applications are open, click Next fo continue. If you want to exit to close your other applications, click Cancel. Figure 6-3: Exit Applications 4. A license agreement will appear next. Scroll down or press PAGE DOWN to read the entire agreement. To accept the terms and continue the installation, click Yes. To quit the installation, Click No.
Wireless-G Access Point 5. On this screen, you will be informed where the Linksys Wireless Guard will be installed. To install to the folder, click Next. If you want to choose a different location for the folder, click the Browse button and select the location. Click Back to return to the previous screen. Click Cancel to cancel the installation. Figure 6-5: Destination Location 6. The program files will start copying. Click Next to continue. Click Back to return to the previous screen.
Wireless-G Access Point 7. The Linksys Wireless Guard is successfully installed. Before you can use the program, you must restart your computer. Select Yes to restart your computer now. Select No to restart your computer at a later time. Remove any disks that are in their drives, then click Finish. 8. After the Linksys Wireless Guard is installed, a key icon will be installed on the right-side of the system tray at the bottom of your screen.
Wireless-G Access Point Your Account This section explains how to access your account, how to add a guest, how to add another member to your account, and how to secure and unprotect the Linksys Wireless Guard network. For more detailed information on your account and the website, click on your computer’s Start button, select the Linksys Wireless Guard folder, then click Linksys Wireless Guard Help.
Wireless-G Access Point Add a Guest 1. On the Wireless Guard Member Website home screen, Figure 6-10, click the Network Admin tab. Figure 6-10: Home 2. The screen in Figure 6-11 will appear. Under Network Administration, click Modify Access Control.
Wireless-G Access Point 3. The screen in Figure 6-12 will appear. Under Guests, click Add Guest. Figure 6-12: Modify Access Control 4. The screen in Figure 6-13 will appear. Enter the Guest User Name, Guest First Name, Guest Last Name, Password, Password Verify, Access Duration, then click Submit. Guest User Name. Enter a user name of the guest you want to add. Guest First Name. The first name of the guest you want to add. Guest Last Name. The last name of the guest you want to add. Password.
Wireless-G Access Point Add a Member To add a member, follow instructions for Add a Guest, steps 1 through 3 above, except in step 3, click Add Member. The screen in Figure 6-14 will appear. Registered members can enter their Email address in the field and select the duration for access from the drop-down menu. If you want this network member to have the authority to put the network into Fallback Mode in case network security is lost, select Permission to Initiate Network Fallback.
Wireless-G Access Point 3. When the Enter subscriber informatlion screen appears, enter the first and last names, the phone number, if desired, then the E-mail address of the new member. Click Next. Click Back to return to the previous screen. Click Cancel to cancel the member registration. Figure 6-16: Subscriber Information 4. When the next screen appears, choose who will be paying for the account. If the new member will be paying for the account, click I will pay for my own subscription.
Wireless-G Access Point 5. When this screen appears, enter the information you will be using with the account. Enter a user name, password, then the password again. Also select a security question and answer in case you forget your password in the future. Click Next to continue. Click Back to return to the previous screen. Click Cancel to cancel the member registration. Figure 6-18: Credentials Information 6.
Wireless-G Access Point Securing or Unprotecting your Wireless Guard Network There may be some instances where you would want to completely unprotect your network connection so it is not using the Wireless Guard security. For example, if you take your laptop to another location to give a presentation, and connect to a network that is running 802.1x security, the Linksys Wireless Guard software on your laptop will prevent you from logging in to another network.
Wireless-G Access Point Chapter 7: Configuring the Wireless-G Access Point Overview The Access Point has been designed to be functional right out of the box, with the default settings in the Setup Wizard. However, if you'd like to change these settings, the Access Point can be configured through your web browser with the Web-Based Utility. This chapter explains how to configure the Access Point in this manner. For your convenience, use the Access Point’s Web-based Utility to administer it.
Wireless-G Access Point Navigating the Utility There are four main tabs: Setup, Status, Advanced, and Help. Additional screens will be available from the main tabs. Setup • Basic Setup. Enter the Internet connection and network settings on this screen. • Password. Change the Access Point’s Password and change its settings back to their defaults from this screen. • AP Mode. From this screen, you can configure how the Access Point will work with other access points in your network. • Log.
Wireless-G Access Point Accessing the Utility To access the Web-based Utility of the Access Point, launch Internet Explorer or Netscape Navigator, and enter the Access Point’s default IP address, 192.168.1.245, in the Address field. Press the Enter key. Open your web browser and type the IP Address you entered in the Setup Wizard. (The default IP address is 192.168.1.245.) (Should you need to learn what IP Address the Access Point presently uses, run the Setup Wizard again.
Wireless-G Access Point The Setup Tab Basic Setup The first screen that appears displays the Basic Setup screen. This allows you to change the Access Point's general settings. Change these settings as described here and click Save Settings to apply your changes or Cancel Changes to cancel your changes. If you require online help, click Help. • Firmware. This will display the Access Point's current firmware version. Firmware can be upgraded from the Help tab. • AP Name.
Wireless-G Access Point Wireless The selections under this heading allow you to configure the Access Point’s connection to your wireless network. • Mode. Select Mixed and both Wireless-G and Wireless-B computers will be allowed on the network, but the speed will be reduced. Select G-Only for maximum speed with Wireless-G products only. The final selection, B-Only, allows only Wireless-B products on the network. • SSID. The SSID is the unique name shared among all points in a wireless network.
Wireless-G Access Point Wireless Security Settings The Wireless Security settings configure the security of your wireless network. There are four wireless security mode options supported by the Access Point: WPA Pre-Shared Key, WPA RADIUS, RADIUS, and WEP. (WPA stands for Wi-Fi Protected Access, which is a security standard stronger than WEP encryption. WEP stands for Wired Equivalent Privacy, while RADIUS stands for Remote Authentication Dial-In User Service.) These four are briefly discussed here.
Wireless-G Access Point RADIUS. This option features WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Access Point.) First, enter the RADIUS server’s IP Address and port number, along with a key shared between the Access Point and the server. Then, select a Default Transmit Key (choose which Key to use), and a level of WEP encryption, 64 bits 10 hex digits or 128 bits 26 hex digits.
Wireless-G Access Point Password The Password screen allows you to change the Access Point's password and restore factory defaults. Changing the sign-on password for the Access Point is as easy as typing the password into the AP Password field. Then, type it again into the second field to confirm. To restore the Access Point's factory default settings, click the Yes button beside Restore Factory Defaults. To back up your Access Point configuration, click the Backup button.
Wireless-G Access Point AP Mode LAN MAC Address The Access Point offers five modes of operation: Access Point, AP (Access Point) Client, Wireless Repeater, and Wireless Bridge. For the bridging mode and Repeater mode, make sure the channel, SSID, and WEP keys are the same. IMPORTANT: For all modes of operation EXCEPT Access Point, the remote access point must be a second Linksys Wireless Network Access Point. The Access Point will not communicate with any other kind of remote access point.
Wireless-G Access Point Wireless Repeater - When set to Wireless Repeater mode, the Wireless Repeater is able to talk to one remote access point within its range and retransmit its signal. (This feature only works with Linksys WAP54G and WRT54G.) To configure a Wireless Repeater environment, click Wireless Repeater and enter the LAN MAC address of the remote access point in the Remote AP MAC Address field.
Wireless-G Access Point Log To view a log of the Access Point’s activity, select the Log tab. To enable permanent logging activity, select Enable. The default setting for this function is Disable. If you have chosen to monitor the Access Point’s traffic, then you can designate a PC that will receive permanent log files periodically. In the Send Log to field, enter the IP address of this PC. To view these permanent logs, you must use Logviewer software, which can be downloaded free of charge from www.
Wireless-G Access Point The Status Tab The Status tab displays the Access Point’s current status. Firmware Version. This is the version of the Access Point’s current firmware. AP Name. This is the Access Point name specified on the Basic Setup screen. MAC Address. This is the Access Point’s MAC Address, as seen by your ISP. Configuration Type.
Wireless-G Access Point The Advanced Tab Filters Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s radius. Wireless MAC Filter. To filter wireless users by MAC Address, either permitting or blocking access, click Enable. If you do not wish to filter users by MAC Address, select Disable. Prevent. Clicking this button will block wireless access by MAC Address. Permit Only. Clicking this button will allow wireless access by MAC Address.
Wireless-G Access Point Advanced Wireless Before making any changes to the Wireless tab, please check your wireless settings on other systems, as these changes will alter the effectiveness of the Access Point. In most cases, these settings do not need to be changed. Authentication Type. The default is set to Auto, where it auto-detects for Shared Key or Open System. Shared Key is when both the sender and the recipient share a WEP key for authentication.
Wireless-G Access Point Fragmentation Length. This specifies the maximum size a data packet will be before splitting and creating a new packet and should remain at its default setting of 2,346. A smaller setting means smaller packets, which will create more packets for each transmission. If you have decreased this value and experience high packet error rates, you can increase it again, but it will likely decrease overall network performance. Only minor modifications of this value are recommended.
Wireless-G Access Point SNMP The SNMP screen allows you to customize the Simple Network Management Protocol (SNMP) settings. SNMP is a popular network monitoring and management protocol. The Identification settings let you designate the Contact, Device Name, and Location information for the Access Point. The SNMP Community settings allow names to be assigned to any SNMP communities that have been set up in the network.
Wireless-G Access Point The Help Tab For help on the various tabs in this Web-based Utility, along with upgrading the Access Point’s firmware and viewing this User Guide, click the Help tab. The help files for the various tabs in this Web-based Utility are listed by tab name on the lefthand side of the screen. Click the Linksys Website link to connect to the Linksys homepage for Knowledgebase help files and information about other Linksys products, provided you have an active Internet connection.
Wireless-G Access Point Appendix A: Troubleshooting This appendix provides solutions to problems that may occur during the installation and operation of the Wireless-G Access Point. Read the description below to solve your problems. If you can't find an answer here, check the Linksys website at www.linksys.com. Frequently Asked Questions Can the Access Point act as my DHCP Server? No. The Access Point is nothing more than a wireless hub, and as such cannot be configured to handle DHCP capabilities.
Wireless-G Access Point What is Roaming? Roaming is the ability of a portable computer user to communicate continuously while moving freely throughout an area greater than that covered by a single Access Point. Before using the roaming function, the workstation must make sure that it is the same channel number as the Access Point of the dedicated coverage area. To achieve true seamless connectivity, the wireless LAN must incorporate a number of different functions.
Wireless-G Access Point What is DSSS? What is FHSS? And what are their differences? Frequency Hopping Spread Spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct Sequence Spread Spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted.
Wireless-G Access Point How do I resolve issues with signal loss? There is no way to know the exact range of your wireless network without testing. Every obstacle placed between an Access Point and wireless PC will create signal loss. Leaded glass, metal, concrete floors, water and walls will inhibit the signal and reduce range. Start with your Access Point and your wireless PC in the same room and move it away in small increments to determine the maximum range in your environment.
Dual-Band Wireless Access Point Appendix B: Wireless Security Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation. So, keep the following in mind whenever you are setting up or using your wireless network.
Dual-Band Wireless Access Point SSID. There are several things to keep in mind about the SSID: 1. Disable Broadcast 2. Make it unique 3. Change it often Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast the SSID. Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.
Dual-Band Wireless Access Point WPA Pre-Shared Key. If you do not have a RADIUS server, select the type of algorithm, TKIP or AES, enter a password in the Pre-Shared key field of 8-64 characters, and enter a Group Key Renewal period time between 0 and 99,999 seconds, which instructs the Router or other device how often it should change the encryption keys. WPA RADIUS. WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router or other device.
Wireless-G Access Point Appendix C: Upgrading Firmware The Access Point's firmware is upgraded through the Web-Utility's Help tab. Follow these instructions: 1. Download the firmware from Linksys's website at www.linksys.com. 2. Click the Web-Utility's Help tab, and click the Upgrade Firmware button. 3. From the Upgrade Firmware screen, enter the location of the firmware's file or click the Browse button to find the file. 4. Then, click the Upgrade button to upgrade the firmware.
Wireless-G Access Point Appendix D: Windows Help All wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix. TCP/IP Before a computer can communicate with the Access Point, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network.
Wireless-G Access Point Appendix E: Glossary 802.11b - An IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz. 802.11g - An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices. Adapter - This is a device that adds network functionality to your PC.
Wireless-G Access Point DSSS (Direct-Sequence Spread-Spectrum) - Frequency transmission with a redundant bit pattern resulting in a lower probability of information being lost in transit. DTIM (Delivery Traffic Indication Message) - A message included in data packets that can increase wireless efficiency. Encryption - Encoding data transmitted in a network. Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium.
Wireless-G Access Point Packet - A unit of data sent over a network. Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption keys for Linksys products. Port - The connection point on a computer or networking device used for plugging in cables or adapters. Roaming - The ability to take a wireless device from one access point's range to another without losing the connection.
Wireless-G Access Point TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted. Topology - The physical layout of a network. Upgrade - To replace existing software or firmware with a newer version. WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for greater security.
Wireless-G Access Point Appendix F: Specifications Standards 802.11g and 802.11b Channels 802.11g Ports/Buttons One 10/100 RJ-45 Port, One Power Port, One Reset Button Cabling Type UTP CAT 5 or better Data Rate Up to 54Mbps Transmit Power 15dBm LEDs Power, Act, Link Dimensions (L x W x H) 7.31" x 1.88" x 6.88" (186 mm x 48 mm x 175 mm) Antenna Height 4.5" (114 mm) Unit Weight 15 oz. (0.42 kg) Power External, 12V DC Certifications FCC, Canada Operating Temp.
Wireless-G Access Point Operating Humidity 10% to 85% Non-Condensing Storage Humidity 5% to 90% Non-Condensing Appendix F: Specifications 60
Wireless-G Access Point Appendix G: Warranty Information LIMITED WARRANTY Linksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser.
Wireless-G Access Point Appendix H: Regulatory Information FCC STATEMENT This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Wireless-G Access Point EN 300-328-1, EN 300-328-2 Technical requirements for Radio equipment. Caution: This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact local Authority for procedure to follow.
Wireless-G Access Point Appendix I: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com or ftp.linksys.
Also Available: · Linksys High Gain Antenna for TNC Connectors (HG5T)
