® A Division of Cisco Systems, Inc. Broadband Router with 2 Phone Ports Voice User Guide Model No.
Broadband Router with 2 Phone Ports Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.
Broadband Router with 2 Phone Ports Table of Contents Chapter 1: Introduction Welcome What’s in this Guide? Chapter 2: Networking Basics 1 1 2 5 An Introduction to Local Area Networks The Use of IP Addresses 5 5 Chapter 3: Getting to Know the Router 7 The Back Panel The Front Panel Chapter 4: Connecting the Router Overview Connecting the Router to Your Broadband Modem Connecting the Router to Your Existing Router Placement Options Chapter 5: Configuring the Router Overview How to Access the Web-b
Broadband Router with 2 Phone Ports Appendix I: Contact Information 95
Broadband Router with 2 Phone Ports List of Figures Figure 3-1: Back Panel Figure 3-2: Front Panel Figure 4-1: Connect the Modem Figure 4-2: Connect a PC Figure 4-3: Connect the Power Figure 4-4: Connect a Telephone Figure 4-5: Router Connected to Another Router Figure 4-6: Connect the Existing Router Figure 4-7: Connect the Power Figure 4-8: Connect a Telephone Figure 4-9: Attaching the Stand (Optional) Figure 4-10: Measurement between Wall-Mount Slots Figure 5-1: Router’s IP Address Figure 5-2: Router Lo
Broadband Router with 2 Phone Ports Figure 5-29: DHCP Active IP Table Figure 5-30: Status Tab - Voice Figure 5-31: Voice Tab Figure B-1: IP Configuration Screen Figure B-2: MAC/Adapter Address Figure B-3: MAC/Physical Address Figure B-4: MAC Address Clone Figure B-5: MAC Address Filter 45 46 47 69 69 70 70 70 Figure 3-1: Back Panel Figure 3-2: Front Panel Figure 4-1: Connect the Modem Figure 4-2: Connect a PC Figure 4-3: Connect the Power Figure 4-4: Connect a Telephone Figure 4-5: Router Connected to An
Broadband Router with 2 Phone Ports Figure B-1: IP Configuration Screen Figure B-2: MAC/Adapter Address Figure B-3: MAC/Physical Address Figure B-4: MAC Address Clone Figure B-5: MAC Address Filter 69 69 70 70 70
Broadband Router with 2 Phone Ports Chapter 1: Introduction Welcome Thank you for choosing the Broadband Router with 2 Phone Ports. This Router will allow your computers to share a high-speed Internet connection as well as resources, including files and printers. And after you have set up your Internet phone service, you will be able to make phone or fax calls using the Internet.
Broadband Router with 2 Phone Ports To create your network, install and set up the Router. To guide you through the process, use the instructions in this Installation and Troubleshooting Guide to help you. These instructions should be all you need to get the most out of the Router. What’s in this Guide? This guide covers the basic steps for setting up a network with a router.
Broadband Router with 2 Phone Ports • Appendix B: Finding the MAC Address and IP Address for Your Ethernet Adapter This appendix instructs you on how to find the MAC address or Ethernet address of your PC’s Ethernet network adapter. • Appendix C: Windows Help This appendix describes how you can use Windows Help for instructions about networking, such as installing the TCP/IP protocol. • Appendix D: Glossary This appendix gives a brief glossary of terms frequently used in networking.
Broadband Router with 2 Phone Ports Chapter 2: Networking Basics An Introduction to Local Area Networks Simply put, a router is a network device that connects two networks together. The Router connects your local area network (LAN), or the group of PCs in your home or office, to the Internet. The Router processes and regulates the data that travels between these two networks.
Broadband Router with 2 Phone Ports If you use the Router to share your cable or DSL Internet connection, contact your ISP to find out if they have assigned a static IP address to your account. If so, you will need that static IP address when configuring the Router. You can get the information from your ISP. A dynamic IP address is automatically assigned to a device on the network. These IP addresses are called dynamic because they are only temporarily assigned to the PC or other device.
Broadband Router with 2 Phone Ports Chapter 3: Getting to Know the Router The Back Panel The Router’s ports and the Reset button are located on the back panel of the Router. Figure 3-1: Back Panel Internet This Internet port connects to your cable or DSL modem. Phone1 For your primary Internet phone line, the Phone1 port allows you to connect the Router to your telephone (or fax machine) using an RJ-11 telephone cable (not included).
Broadband Router with 2 Phone Ports The Front Panel The Router’s LEDs, which inform you about network activities, are located on the front panel. Figure 3-2: Front Panel POWER Blue/Red. The POWER LED lights up blue when the Router is powered on. If the blue LED is flashing, the Router is booting up or upgrading its firmware. If the LED lights up red, then disconnect the power, and wait five seconds. Then reconnect the power. ETHERNET 1-4 Blue.
Broadband Router with 2 Phone Ports Chapter 4: Connecting the Router Overview This chapter includes two sets of instructions. If the Broadband Router with 2 Phone Ports will be the only router in your network, follow the instructions in “Connecting the Router to Your Broadband Modem.” If you already have a router in your network and want to add the Broadband Router with 2 Phone Ports, follow the instructions in “Connecting the Router to Your Existing Router.
Broadband Router with 2 Phone Ports 4. Power on the broadband modem. 5. Connect the included power adapter to the Router’s Power port, and then plug the power adapter into an electrical outlet. The Power LED on the front panel will light up as soon as the Router powers on. Figure 4-3: Connect the Power 6. Plug a standard telephone into the Router’s Phone1 port. IMPORTANT: Do not connect the Phone port to a telephone wall jack. Make sure you only connect a telephone or fax machine to the Phone port.
Broadband Router with 2 Phone Ports Connecting the Router to Your Existing Router Linksys recommends that you replace your existing router with the Broadband Router with 2 Phone Ports. However, if you would like to keep your existing router because it has wireless capability or other features, then you can use the following instructions to connect the Broadband Router with 2 Phone Ports to your existing router, while keeping your wired PCs connected to your existing router.
Broadband Router with 2 Phone Ports To connect the Broadband Router with 2 Phone Ports to your existing router, follow these instructions: 1. Connect an Ethernet cable to the Internet port on the back of the Broadband Router with 2 Phone Ports. Then connect the other end to one of the Ethernet network ports on your existing router. 2. Connect the included power adapter to the Power port of the Broadband Router with 2 Phone Ports, and then plug the power adapter into an electrical outlet.
Broadband Router with 2 Phone Ports Placement Options There are three ways to place the Router. The first way is to place it horizontally on a surface, so it sits on its four rubber feet. The second way is to stand the Router vertically on a surface (this uses an optional stand). The third way is to mount it on a wall. The second and third options are explained in further detail below. Stand Option If you have the optional stand, then you can place the Router vertically on a surface. 1.
Broadband Router with 2 Phone Ports Wall-Mount Option The Router has four wall-mount slots on its bottom panel. The distance between two adjacent slots is 62 mm (2.44 inches). Before you begin, make sure you have four screws that are size #4—this indicates a diameter measurement of 2.845 mm. 62 mm (2.44 inches) 1. Determine where you want to mount the Router. 2. Drill four holes into the wall. Make sure adjacent holes are 62 mm apart. 3. Insert a screw into each hole, and leave 5 mm of its head exposed.
Broadband Router with 2 Phone Ports Chapter 5: Configuring the Router Overview Use the Web-based Utility to configure the Router. This chapter will describe each web page on the Utility and each page’s key functions. The Utility can be accessed via your web browser through use of a computer connected to the Router. For a basic network setup, most users only have to use the following screens of the Utility: • Basic Setup.
Broadband Router with 2 Phone Ports Setup • Basic Setup. Enter the Internet connection and network settings on this screen. • DDNS. Enable the Router’s Dynamic Domain Name System (DDNS) feature on this screen. • MAC Address Clone. If you need to clone a MAC address onto the Router, use this screen. • Advanced Routing. On this screen, you can alter firewall, Network Address Translation (NAT), Dynamic Routing, and Static Routing configurations. Security • Firewall.
Broadband Router with 2 Phone Ports Applications & Gaming • Port Range Forwarding. Set up public services or other specialized Internet applications on your network. • Port Triggering. To set up triggered ranges and forwarded ranges for Internet applications, click this tab. • DMZ. Click this tab to allow one local user to be exposed to the Internet for use of special-purpose services. • QoS. Enable QoS (Quality of Service) to maximize network performance. Administration • Management.
Broadband Router with 2 Phone Ports Voice Access to the Voice tab is restricted by your Internet phone service provider. Contact your provider for more information. How to Access the Web-based Utility To access the Web-based Utility of the Router, launch Internet Explorer or Netscape Navigator, and enter the Router’s default IP address, 192.168.15.1, in the Address field. Press the Enter key. The Login screen will appear asking you for your User name and Password.
Broadband Router with 2 Phone Ports The Setup Tab - Basic Setup The Basic Setup screen is the first screen you see when you access the Web-based Utility. Internet Setup The Internet Setup section configures the Router for your Internet connection type. This information can be obtained from your ISP. Internet Connection Type The Router supports three connection types: Obtain an IP automatically, Static IP, and PPPoE.
Broadband Router with 2 Phone Ports Static IP If you are required to use a permanent IP address, then select Static IP. IP Address. This is the IP address that the Router has, when seen from the Internet. Your ISP will provide you with the IP Address you need to specify here. Subnet Mask. This is the Router’s Subnet Mask, as seen by external users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask. Gateway. Your ISP will provide you with the Default Gateway Address.
Broadband Router with 2 Phone Ports button. If you want your Internet connection to remain on at all times, enter 0 in the Idle Timeout field. Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects. Keep Alive and Redial Period. This option keeps your Internet access connected indefinitely, even when it sits idle. If you select this option, the Router will periodically check your Internet connection.
Broadband Router with 2 Phone Ports Router IP The values for the Router’s Local IP Address and Subnet Mask are shown here. In most cases, keeping the default values will work. Local IP Address. The default value is 192.168.15.1. Subnet Mask. The default value is 255.255.255.0. Network Address Server Settings (DHCP) These settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The Router can be used as a DHCP server for your network.
Broadband Router with 2 Phone Ports Client Lease Time. The Client Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP address. Enter the amount of time, in minutes, that the user will be “leased” this dynamic IP address. After the dynamic IP address has expired, the user will be automatically assigned a new dynamic IP address. The default is 0 minutes, which means one day.
Broadband Router with 2 Phone Ports DynDNS.org User Name, Password, and Host Name. Enter the User Name, Password, and Host Name of the account you set up with DynDNS.org. Internet IP Address. The Router’s current Internet IP Address is displayed here. Because it is dynamic, this will change. Status. The status of the DDNS service connection is displayed here. TZO.com Figure 5-6: Setup Tab - DDNS (DynDNS.org) E-mail Address, Password, and Domain Name.
Broadband Router with 2 Phone Ports The Setup Tab - MAC Address Clone A MAC address is a 12-digit code assigned to a unique piece of hardware for identification, like a social security number. Some ISPs will require you to register a MAC address in order to access the Internet. If you do not wish to re-register the MAC address with your ISP, you may assign the MAC address you have currently registered with your ISP to the Router with the MAC Address Clone feature. MAC Clone MAC Clone Service.
Broadband Router with 2 Phone Ports The Setup Tab - Advanced Routing The Advanced Routing screen allows you to configure the firewall, Network Address Translation (NAT), dynamic routing, and static routing settings. Advanced Routing Firewall & NAT. The Stateful Packet Inspection (SPI) firewall reviews data packets entering your network. NAT is a security feature that enables the Router to translate IP addresses of your local area network to a different IP address for the Internet.
Broadband Router with 2 Phone Ports Subnet Mask. The Subnet Mask determines which portion of a Destination IP address is the network portion, and which portion is the host portion. Gateway. This is the IP address of the gateway device that allows for contact between the Router and the remote network or host. Hop Count. This determines the maximum number of steps between network nodes that data packets will travel. A node is any device on the network, such as PCs, print servers, routers, etc. Interface.
Broadband Router with 2 Phone Ports The Security Tab - Firewall When you click the Security tab, you will see the Firewall screen. You can use this screen to enable a variety of web filters, which will enhance the firewall protecting your network. Web Filters Figure 5-11: Security Tab - Firewall Filter Proxy. Use of WAN proxy servers may compromise the Gateway's security. Denying Filter Proxy will disable access to any WAN proxy servers. To enable proxy filtering, click the checkbox. Filter Java Applets.
Broadband Router with 2 Phone Ports The Security Tab - VPN Passthrough The VPN Passthrough screen allows you to allow VPN tunnels using IPSec, PPPoE, or PPTP protocols to pass through the Router. VPN Passthrough IPSec Passthrough. IPSec (Internet Protocol Security) is a suite of protocols used to implement secure exchange of packets at the IP layer. To allow IPSec Passthrough, click the Enabled button. To disable IPSec Passthrough, click the Disabled button.
Broadband Router with 2 Phone Ports The Access Restrictions Tab - Filter Filters can block specific internal users from accessing the Internet, anonymous Internet requests, and/or multicasting. Filter IP Address Range You can create up to five different IP Address filters. To set up a filter, enter the IP address you wish to filter in the field provided. Users who have filtered IP addresses will not be able to access the Internet at all.
Broadband Router with 2 Phone Ports Block WAN Requests Use these features to enhance your network’s security and filter multicasting. Block Anonymous Internet Requests. This keeps your network from being “pinged” or detected and reinforces your network security by hiding your network ports, so it is more difficult for intruders to work their way into your network. Select Enabled to block anonymous Internet requests, or Disabled to allow anonymous Internet requests. Filter Multicast.
Broadband Router with 2 Phone Ports The Access Restrictions Tab - Device Access Control Use this screen to control local and remote access to the Router’s management ports via different services. Access Control Enable Access Control. If you want to control access to the Router’s management ports via the services listed below, click the checkbox. For each service, make sure the appropriate checkbox is checked if you want to allow local or remote access.
Broadband Router with 2 Phone Ports The Applications & Gaming Tab - Port Range Forwarding When you click the Applications & Gaming tab, you will see the Port Range Forwarding screen. Port Range Forwarding sets up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform functions such as videoconferencing or online gaming.
Broadband Router with 2 Phone Ports Enable. Check the Enable box to enable the services you have defined. Port Range Forwarding will not function if the Enabled button is left unchecked. This is disabled (unchecked) by default. When you have finished making changes to this screen, click the Save Settings button to save the changes, or click the Cancel Changes button to undo your changes.
Broadband Router with 2 Phone Ports Forwarded Range For each application, list the forwarded port number range. Check with the Internet application documentation for the port number(s) needed. Start Port. Enter the starting port number of the Forwarded Range. End Port. Enter the ending port number of the Forwarded Range. When you have finished making changes to this screen, click the Save Settings button to save the changes, or click the Cancel Changes button to undo your changes.
Broadband Router with 2 Phone Ports The Applications & Gaming Tab - DMZ The DMZ screen allows one local user to be exposed to the Internet for use of a special-purpose service such as Internet gaming and videoconferencing. DMZ hosting forwards all the ports at the same time to one PC. The Port Range Forwarding is more secure because it only opens the ports you want to have opened, while DMZ hosting opens all the ports of one computer, exposing the computer to the Internet.
Broadband Router with 2 Phone Ports The Applications & Gaming Tab - QoS Quality of Service (QoS) ensures better service to high-priority types of network traffic, which may involve demanding, real-time applications, such as Internet phone calls or videoconferencing. Use this screen to configure IP QoS for connections, view the rules you have set up, and manage your rules. IP QoS Choose a connection. Choose the appropriate connection from the drop-down menu. Low priority weight.
Broadband Router with 2 Phone Ports To create a rule, follow these instructions: 1. Click the Add button located below the table of rules. 2. A new screen will appear. Enter a name in the Rule Name field. 3. Identify the application traffic by providing the following information: Source IP, Source Netmask, Source Start and End Ports, Destination IP, Destination Netmask, Destination Start and End ports, and Packet Length Start and End settings.
Broadband Router with 2 Phone Ports The Administration Tab - Management When you click the Administration tab, you will see the Management screen. This screen allows you to change the Router’s access settings as well as configure the UPnP (Universal Plug and Play) feature. Router Password Local Router Access To ensure the Router’s security, you will be asked for your user name and password when you access the Router’s Web-based Utility. The default user name and password is admin. User Name.
Broadband Router with 2 Phone Ports The Administration Tab - Log When you click the Administration tab, you will see the Log screen. You can select which PC will receive the specified type of system logs for your Internet connection. NOTE: The PC that receives these logs must be running a SYSLOG application. Linksys offers free software that can view system logs. You can download Logviewer software at www.linksys.com. Log Figure 5-22: Administration Tab - Log Log Level.
Broadband Router with 2 Phone Ports The Administration Tab - Factory Defaults The Factory Defaults screen allows you to reset the Router to its router factory defaults. If you want to reset the Router to its voice factory defaults, then you need a password available only from your Internet phone service provider. Contact your provider for more information. Factory Defaults Restore Router Factory Defaults.
Broadband Router with 2 Phone Ports The Administration Tab - Diagnostics The diagnostic tests allow you to check the connections of your network components. Ping Test Ping Parameters. The Ping test will check the status of a connection. Click the Ping button to open the Ping Test screen. Enter the IP address or domain name of the PC whose connection you wish to test. Enter the size of the test packet. Then select the number of times you want the ping to occur. Click the Ping button.
Broadband Router with 2 Phone Ports The Status Tab - Router The Router screen displays information about the Router and its current settings. The on-screen information will vary depending on the Internet Connection Type selected on the Setup screen. Information Firmware Version. This shows the version number of the installed firmware. Current Time. The current time and date are displayed here when the Router is connected to the Internet. MAC Address.
Broadband Router with 2 Phone Ports DHCP Release. Available for a DHCP connection, click the DHCP Release button to release the current IP address of the device connected to the Router’s Internet port. DHCP Renew. Available for a DHCP connection, click the DHCP Renew button to replace the current IP address—of the device connected to the Router’s Internet port—with a new IP address. Click the Refresh button to update the on-screen information.
Broadband Router with 2 Phone Ports The Status Tab - Local Network The Local Network screen displays information about the local network. Local Network MAC Address. The MAC Address of the Router’s LAN (local area network) interface is displayed here. IP Address. The Router’s local IP Address is shown here. Figure 5-28: Status Tab - Local Network Subnet Mask. The Router’s Subnet Mask is shown here. DHCP Server. The status of the DHCP server is displayed here. DHCP Clients Table.
Broadband Router with 2 Phone Ports The Status Tab - Voice The Voice screen displays information about your Internet phone line(s). Information Provisioning Status. This status information indicates whether the Router has been configured by your Internet phone service provider. Line1 Status Registration Status. The phone number and status of this Internet phone line are displayed here. If it is not registered, then you should register it.
Broadband Router with 2 Phone Ports The Voice Tab Access to the Voice tab is restricted by your Internet phone service provider. Contact your provider for more information.
Broadband Router with 2 Phone Ports Appendix A: Troubleshooting This appendix provides solutions to problems that may occur during the installation and operation of the Router. Read the description below to solve your problems. If you can't find an answer here, check the your Internet phone service provider’s website or the Linksys website at www.linksys.com. Common Problems and Solutions 1. I don’t hear a dial tone, and the PHONE1 (or PHONE2) LED is not lit.
Broadband Router with 2 Phone Ports B. Press CTRL + F5. This is a hard refresh, which will force Windows Explorer to load new webpages, not cached ones. C. Click Tools. Click Internet Options. Click the Security tab. Click the Default level button. Make sure the security level is Medium or lower. Then click the OK button. 3. I need to set a static IP address on a PC. The Router, by default, assigns an IP address range of 192.168.15.100 to 192.168.15.150 using the DHCP server on the Router.
Broadband Router with 2 Phone Ports F. Click the OK button in the TCP/IP properties window, and click Close or the OK button for the Network window. G. Restart the computer when asked. For Windows 2000: A. Click Start, Settings, and Control Panel. Double-click Network and Dial-Up Connections. B. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using, and select the Properties option. C.
Broadband Router with 2 Phone Ports A. Click Start and Control Panel. B. Click the Network and Internet Connections icon and then the Network Connections icon. C. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using, and select the Properties option. D. In the This connection uses the following items box, highlight Internet Protocol (TCP/IP). Click the Properties button. E.
Broadband Router with 2 Phone Ports 3. In the Components checked are used by this connection box, highlight Internet Protocol (TCP/IP), and click the Properties button. Make sure that Obtain an IP address automatically and Obtain DNS server address automatically are selected. 4. Click the OK button in the Internet Protocol (TCP/IP) Properties window, and click the OK button in the Local Area Connection Properties window. 5. Restart the computer if asked. 6.
Broadband Router with 2 Phone Ports • For Windows 2000 and XP, click Start and Run. In the Open field, type cmd. Press the Enter key or click the OK button. C. In the command prompt, type ping 192.168.15.1 and press the Enter key. • If you get a reply, the computer is communicating with the Router. • If you do NOT get a reply, check the cable, and make sure Obtain an IP address automatically is selected in the TCP/IP settings for your Ethernet adapter. D.
Broadband Router with 2 Phone Ports C. Make sure you are using the right Internet settings. Contact your ISP to see if your Internet connection type is DHCP, Static IP Address, or PPPoE (commonly used by DSL consumers). Please refer to the Basic Setup section of “Chapter 5: Configuring the Router” for details on Internet Connection Type settings. D. Make sure you use the right cable. Check to see if the Internet LED is solidly lit. E.
Broadband Router with 2 Phone Ports VPNs that use IPSec and AH (Authentication Header known as protocol 51) are incompatible with the Router. AH has limitations due to occasional incompatibility with the NAT standard. Change the IP address for the Router to another subnet to avoid a conflict between the VPN IP address and your local IP address. For example, if your VPN server assigns an IP address 192.168.15.X (X is a number from 1 to 254) and your local LAN IP address is 192.168.15.
Broadband Router with 2 Phone Ports C. Enter the port range of the service you are using. For example, if you have a web server, you would enter the range 80 to 80. D. Select the protocol you will be using, TCP or UDP, or select Both. E. Enter the IP address of the PC or network device that you want the port server to go to. For example, if the web server’s Ethernet adapter IP address is 192.168.15.100, you would enter 100 in the field provided.
Broadband Router with 2 Phone Ports A. Access the Router’s Web-based Utility by going to http://192.168.15.1 or the IP address of the Router. Go to the Applications & Gaming => Port Range Forwarding tab. B. Enter any name you want to use for the Application. C. Enter the port range of the service you are using. For example, if you have a web server, you would enter the range 80 to 80. D. Select the protocol you will be using, TCP or UDP, or select Both. E.
Broadband Router with 2 Phone Ports application requires too many ports or when you are not sure which port services to use. Make sure you disable all the forwarding entries if you want to successfully use DMZ hosting, since forwarding has priority over DMZ hosting. (In other words, data that enters the Router will be checked first by the forwarding settings.
Broadband Router with 2 Phone Ports 12. I am a PPPoE user, and I need to remove the proxy settings or the dial-up pop-up window. If you have proxy settings, you need to disable these on your computer. Because the Router is the gateway for the Internet connection, the computer does not need any proxy settings to gain access. Please follow these directions to verify that you do not have any proxy settings and that the browser you use is set to connect directly to the LAN. For Microsoft Internet Explorer 5.
Broadband Router with 2 Phone Ports 14. My DSL service’s PPPoE is always disconnecting. PPPoE is not actually a dedicated or always-on connection. The DSL ISP can disconnect the service after a period of inactivity, just like a normal phone dial-up connection to the Internet. There is a setup option to “keep alive” the connection. This may not always work, so you may need to re-establish connection periodically. A. To connect to the Router, go to the web browser, and enter http://192.168.15.
Broadband Router with 2 Phone Ports If your difficulties continue, change the Size to different values. Try this list of values, one value at a time, in this order, until your problem is solved: 1462 1400 1362 1300 16. I need to use port triggering. Port triggering looks at the outgoing port services used and will trigger the Router to open a specific port, depending on which port an Internet application uses. Follow these steps: A. To connect to the Router, go to the web browser, and enter http://192.168.
Broadband Router with 2 Phone Ports • If the Router is configured correctly, check your Internet connection (DSL/cable modem, etc.) to see if it is working correctly. You can remove the Router to verify a direct connection. • Manually configure the TCP/IP with a DNS address provided by your ISP. • Make sure that your browser is set to connect directly and that any dial-up is disabled. For Internet Explorer, click Tools, Internet Options, and then the Connection tab.
Broadband Router with 2 Phone Ports What is the maximum number of IP addresses that the Router will support? The Router will support up to 253 IP addresses. Where is the Router installed on the network? In a typical environment, the Router is installed between the cable/DSL modem and the local area network (LAN). Plug the Router into the cable/DSL modem’s Ethernet port. Does the Router support IPX or AppleTalk? No.
Broadband Router with 2 Phone Ports I set up an Unreal Tournament Server, but others on the LAN cannot join. What do I need to do? If you have a dedicated Unreal Tournament server running, you need to create a static IP for each of the LAN computers and forward ports 7777, 7778, 7779, 7780, 7781, and 27900 to the IP address of the server. You can also use a port forwarding range of 7777 to 27900.
Broadband Router with 2 Phone Ports Advanced Properties tab.) Make sure that your proxy setting is disabled in the browser. Check our website at www.linksys.com for more information. If all else fails in the installation, what can I do? Reset the Router by holding down the Reset button for approximately five seconds. Reset your cable or DSL modem by powering the unit off and then on. Contact your Internet phone service provider for assistance.
Broadband Router with 2 Phone Ports If DMZ Hosting is used, does the exposed user share the public IP with the Router? No. Is the Router cross-platform compatible? Any platform that supports Ethernet and TCP/IP is compatible with the Router. How many ports can be simultaneously forwarded? Theoretically, the Router can establish 520 sessions at the same time, but you can only forward 10 ranges of ports.
Broadband Router with 2 Phone Ports computer logs onto the network, the MAC address of a device stays the same, making it a valuable identifier for the network. How do I reset the Router? Press the Reset button on the back panel for about five seconds. This will reset the Router to its default settings.
Broadband Router with 2 Phone Ports Appendix B: Finding the MAC Address and IP Address for Your Ethernet Adapter This section describes how to find the MAC address for your computer’s Ethernet adapter so you can use the MAC filtering and/or MAC address cloning feature of the Router. You can also find the IP address of your computer’s Ethernet adapter. This IP address is used for the Router’s filtering, forwarding, and/or DMZ features.
Broadband Router with 2 Phone Ports Windows 2000 or XP Instructions 1. Click Start and Run. In the Open field, enter cmd. Press the Enter key or click the OK button. 2. At the command prompt, enter ipconfig /all. Then press the Enter key. 3. Write down the Physical Address as shown on your computer screen; it is the MAC address for your Ethernet adapter. This appears as a series of numbers and letters. The MAC address/Physical Address is what you will use for MAC address cloning or MAC filtering.
Broadband Router with 2 Phone Ports Appendix C: Windows Help Almost all Linksys products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix. TCP/IP Before a computer can communicate with a network router, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network.
Broadband Router with 2 Phone Ports Appendix D: Glossary Adapter - A device that adds network functionality to your PC. Backbone - The part of a network that connects most of the systems and networks together, and handles the most data. Bandwidth - The transmission capacity of a given device or network. Bit - A binary digit. Boot - To start a device and cause it to start executing instructions. Bridge - A device that connects different networks. Broadband - An always-on, fast Internet connection.
Broadband Router with 2 Phone Ports DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (e.g., www.xyz.com) and a dynamic IP address. Default Gateway - A device that forwards Internet traffic from your local area network.
Broadband Router with 2 Phone Ports FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP network. Full Duplex - The ability of a networking device to receive and transmit data simultaneously. Gateway - A device that interconnects networks with different, incompatible communications protocols. Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a time.
Broadband Router with 2 Phone Ports NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different IP address for the Internet. Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or transmission between users. NNTP (Network News Transfer Protocol) - The protocol used to connect to Usenet groups on the Internet. Node - A network junction or connection point, typically a computer or work station.
Broadband Router with 2 Phone Ports SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet. SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol. Software - Instructions for the computer. A series of instructions that performs a particular task is called a “program”. SOHO (Small Office/Home Office) - Market segment of professionals who work at home or in small offices.
Broadband Router with 2 Phone Ports UDP (User Datagram Protocol) - A network protocol for transmitting data that does not require acknowledgement from the recipient of the data that is sent. Upgrade - To replace existing software or firmware with a newer version. Upload - To transmit a file over a network. URL (Uniform Resource Locator) - The address of a file located on the Internet.
Broadband Router with 2 Phone Ports Appendix E: Specifications Model RTP300 Standards IEEE 802.3 (10BaseT), IEEE 802.
Broadband Router with 2 Phone Ports Storage Humidity 80 5% ~ 90% Non-Condensing Appendix E: Specifications
Broadband Router with 2 Phone Ports Appendix F: Warranty Information This Warranty is valid and may be processed only in the country of purchase. Contact your service provider if the warranty support issues are to be handled them as per your service agreements. Linksys warrants to You that, for a period of two years (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use.
Broadband Router with 2 Phone Ports Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.
Broadband Router with 2 Phone Ports Appendix G: Regulatory Information FCC Statement This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Broadband Router with 2 Phone Ports The REN is useful to determine the quantity of devices that may be connected to the telephone line and still have all of those devices ring when your telephone number is called. In most, but not all areas, the sum of RENs should not exceed 5. To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area.
Broadband Router with 2 Phone Ports Safety Notices Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord. Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Industry Canada (Canada) This device complies with Canadian ICES-003 rule. Cet appareil est conforme à la norme NMB-003 d'Industry Canada.
Broadband Router with 2 Phone Ports This document contains important information for users with regards to the proper disposal and recycling of Linksys products.
Broadband Router with 2 Phone Ports Appendix G: Regulatory Information 87
Broadband Router with 2 Phone Ports 88 Appendix G: Regulatory Information
Broadband Router with 2 Phone Ports Appendix G: Regulatory Information 89
Broadband Router with 2 Phone Ports 90 Appendix G: Regulatory Information
Broadband Router with 2 Phone Ports Appendix G: Regulatory Information 91
Broadband Router with 2 Phone Ports Appendix H: End-User Product Disclaimer Appendix H: End-User Product Disclaimer 93
Broadband Router with 2 Phone Ports 94 Appendix H: End-User Product Disclaimer
Broadband Router with 2 Phone Ports Appendix I: Contact Information For customer support, please contact your service provider before contacting Linksys. Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com/international If you experience problems with any Linksys product, you can e-mail us at: In Europe E-mail Address Austria support.at@linksys.com Belgium support.be@linksys.com Denmark support.dk@linksys.com France support.
Broadband Router with 2 Phone Ports In Europe E-mail Address Sweden support.se@linksys.com Switzerland support.ch@linksys.com United Kingdom & Ireland support.uk@linksys.com Outside of Europe E-mail Address Asia Pacific asiasupport@linksys.com (English only) Latin America support.portuguese@linksys.com or support.spanish@linksys.com Middle East & Africa support.mea@linksys.com (English only) U.S. and Canada support@linksys.
www.linksys.
