Wireless-G Access Point Use this guide to install: WAP54G v2 User Guide
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2003 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. LIMITED WARRANTY Linksys warrants to the original end user purchaser ("You") that, for a period of three years, (the "Warranty Period”).
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Wireless-G Access Point INDUSTRY CANADA (CANADA) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations.
Wireless-G Access Point Chapter 1: Introduction Wireless-G Access Point Appendix B: Setting Up the TCP/IP and IPX Protocols Setting Up TCP/IP in Windows TCP/IP Setup for Windows 98 and Millennium IPX Setup for Windows 98 and Millennium TCP/IP Setup for Windows NT 4.0 IPX Setup for Windows NT 4.
Wireless-G Access Point Chapter 2: Planning Your Wireless Network Chapter 3: Getting to Know the Wireless-G Access Point Network Topology The Wireless-G Access Point’s Back Panel A wireless LAN is a group of computers, each equipped with one Instant Wireless Series adapter. Computers in a wireless LAN must be configured to share the same radio channel. The Access Point’s ports, where a network cable is connected, are located on the Access Point’s back panel.
Wireless-G Access Point T The Wireless-G Access Point’s Front Panel Chapter 4: Connecting the Wireless-G Access Point 1. Locate an optimum location for the Access Point. The best place for the Access Point is usually at the center of your wireless network, with line of sight to all of your mobile stations. Figure 3-2 Power Green. The Power LED lights up when the Access Point is powered on. 54g Act Green.
Wireless-G Access Point Chapter 5: Setting Up the Wireless-G Access Point Have You: Connected the Access Point to a hub, switch or router on your wired network as shown in Chapter 4: Connecting the Wireless-G Access Point? The Access Point can only be set up through your wired network. Now that you’ve connected the Access Point to your wired network, you are ready to begin setting it up. This Setup Wizard will take you through all the necessary steps to configure the Access Point.
Wireless-G Access Point 4. The next screen to appear, shown in Figure 5-3, will display a list of access points on your network along with the status information for each access point. If this is the only access point on your network, it will be the only one displayed. If there are more than one displayed, select the Access Point by clicking on it and click the Yes button to continue or No to exit the Setup Wizard. 6. As shown in Figure 5-5, the IP Settings screen will appear next.
Wireless-G Access Point 7. As shown in Figure 5-6, the Basic Settings screen will appear. Enter your wireless network’s SSID and select the channel at which the network broadcasts its wireless signal. Then, click the Next button to continue or Back to return to the previous page. 8. The Security Settings screen (Figure 5-7) will appear next. From this screen, you will set the Wired Equivalent Privacy (WEP) encryption for your wireless network. Select a WEP configuration method and a passphrase.
Wireless-G Access Point 9. The second Security Settings screen, shown in Figure 5-8, shows the WEP key. If you entered a passphrase, then the Key 1 field will display the automatically generated WEP key. If you did not enter a passphrase, then enter a WEP key in the Key 1 field. Each point in your wireless network must use the same WEP key for the network to function properly. Click the Next button to continue or Back to return to the previous page. 10.
Wireless-G Access Point Chapter 6: Configuring the Wireless-G Access Point Note: The Access Point is designed to function properly after using the Setup Wizard. This chapter is provided solely for those who wish to perform more advanced configuration or monitoring. The Access Point has been designed to be functional right out of the box, with the default settings in the Setup Wizard.
Wireless-G Access Point Wireless • MAC Address. The MAC Address of the wireless (2.4 GHz, Draft 802.11g) interface is displayed here. • Mode. Select Mixed and both Wireless-G and Wireless-B computers will be allowed on the network, but the speed will be reduced. Select G-Only for maximum speed, but no Wireless-B users will be allowed on the network. Select B-Only mode for Wireless-B speed. • SSID. The SSID is the unique name shared among all points in a wireless network.
Wireless-G Access Point The Password Tab SETTING THE AP MODE: The AP Mode Tab The Password tab, shown in Figure 6-5, allows you to change the Access Point’s password and restore factory defaults. The Access Point offers two modes of operation: Access Point and Wireless Bridge. For all bridging modes, make sure the channel, SSID, and WEP key settings are the same. Figure 6-5 Figure 6-6 • AP Password. Changing the password for the Access Point is as easy as typing the password into the AP Password field.
Wireless-G Access Point Note: In Wireless Bridge mode, the Access Point can ONLY be accessed by another access point that is in Wireless Bridge mode. In order for your other wireless devices to access the Access Point, you must reset it to Access Point mode. The two modes are mutually exclusive. The Status Tab The Status tab, shown in Figure 6-8, will display current information on the Access Point, its settings, and its performance. Figure 6-7 Figure 6-8 20 • Firmware Version.
Wireless-G Access Point LAN • MAC Address. The MAC Address of the LAN interface is displayed here. • Configuration Type. This displays how the Access Point is assigned an IP address, either Automatic Configuration - DHCP, if assigned by DHCP server, or Static IP Address and its IP Address, Subnet Mask, and Default Gateway address, if assigned by Static IP Address server. • IP Address. This IP address is the unique IP address of the Access Point. • Subnet Mask.
Wireless-G Access Point The Help Tab To upgrade the Access Point’s firmware: For help on the various tabs in this Web-based Utility, along with upgrading the Access Point’s firmware and viewing this User Guide, click the Help tab, shown in Figure 6-10. 1. Download the firmware upgrade file from the Linksys website. 2. Extract the firmware upgrade file. 3. Click the Upgrade Firmware button on the Help screen.
Wireless-G Access Point The Advanced Wireless Tab Figure 6-12 Figure 6-13 Before making any changes to the Advanced Wireless tab, shown in Figure 613, please check your wireless settings on your other systems, because these changes will alter the effectiveness of the Access Point. In most cases, these wireless settings do not need to be changed. Above the MAC Address fields, there is a pull-down menu. This drop-down menu is for selecting the number of computers on your wireless network.
Wireless-G Access Point • Basic Rate. The default value is set to Default. Depending on the wireless mode you have selected, a default set of supported data rates will be selected. The default setting will ensure maximum compatibility with all devices. You may also choose to enable all data rates by selecting ALL. For compatibility with older Wireless-B devices, select 1-2Mbps. • Antenna Selection. The default value is set to Diversity. In Diversity mode, both antennas will be enabled.
Wireless-G Access Point Appendix A: Troubleshooting This chapter provides solutions to problems usually encountered during the installation and operation of the Access Point. Read the description below to solve your problems. If you can’t find an answer here, check the Linksys website at www.linksys.com. Frequently Asked Questions Can the Access Point act as my DHCP Server? No. The Access Point is nothing more than a wireless hub, and as such cannot be configured to handle DHCP capabilities.
Wireless-G Access Point worldwide. This presents a truly revolutionary opportunity to place convenient high speed wireless capabilities in the hands of users around the globe. What is Spread Spectrum? Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security.
Wireless-G Access Point What is the maximum number of users the Access Point facilitates? No more than 65, but this depends on the volume of data and may be less if many users create a large amount of network traffic. How many channels/frequencies are available with the Access Point? Using 802.11b or draft 802.11g, there are eleven available channels, ranging from 1 to 11.
Wireless-G Access Point The following instructions are provided as examples for reference only. For complete instructions on installing and troubleshooting TCP/IP and IPX, consult your Windows operating system documentation. TCP/IP Setup for Windows 98 and Millennium TCP/IP Setup for Windows NT 4.0 1. Click the Start button, select Settings, and open the Control Panel. Inside the Control Panel, double-click the Network icon. 1. Click the Start button, select Settings, and open the Control Panel.
Wireless-G Access Point 2. When the Network window appears, click the Protocols tab. Then, click the Add button. 4. Select NWLink IPX/SPX/NetBIOS Compatible Transport Protocol from the list and click the OK button. 3. Find the IPX/SPX protocol in the Select Network Protocol field. Click it once and click the OK button. 5. When the Network window reappears, click the OK button. Restart your computer. NWLink IPX/SPX/NetBIOS Compatible Transport Protocol has now been successfully installed.
Wireless-G Access Point Appendix C: Glossary 802.11b - One of the IEEE standards for wireless networking hardware. Products that adhere to a specific IEEE standard will work with each other, even if they are manufactured by different companies. The 802.11b standard specifies a maximum data transfer rate of 11Mbps, an operating frequency of 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. 802.11g - A proposed, but as yet unratified extension of the IEEE 802.
Wireless-G Access Point unique IP address. When an organization sets up its computer users with a connection to the Internet, an IP address must be assigned to each machine. Without DHCP, the IP address must be entered manually at each computer and, if computers move to another location in another part of the network, a new IP address must be entered.
Wireless-G Access Point IEEE (The Institute of Electrical and Electronics Engineers) - The IEEE describes itself as "the world's largest technical professional society, promoting the development and application of electrotechnology and allied sciences for the benefit of humanity, the advancement of the profession, and the well-being of our members." The IEEE fosters the development of standards that often become national and international standards.
Wireless-G Access Point Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services. units of data (called packet) that a message is divided into for efficient routing through the Internet. Software - Instructions for the computer. A series of instructions that performs a particular task is called a "program." The two major categories of software are "system software" and "application software.
Wireless-G Access Point Appendix D: Specifications Standards 11 Channels (USA) 13 Channels (Europe) 14 Channels (Japan) 48 Dimensions 7.32" x 6.89" x 1.89" (186 mm x 175 mm x 48 mm) Unit Weight 18.25 oz. (0.51 kg) Certifications FCC Class B Operating Temp. 32ºF to 104ºF (0ºC to 40ºC) Storage Temp. -4ºF to 158ºF (-20ºC to 70ºC) Operating Humidity 10% to 80%, Non-Condensing Storage Humidity 5% to 90%, Non-Condensing IEEE 802.11g, IEEE 802.
Wireless-G Access Point Appendix E: Warranty Information BE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODE FROM THE PRODUCT’S PACKAGING ON HAND WHEN CALLING. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. IN NO EVENT SHALL LINKSYS’S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS DOCUMENTATION. LINKSYS DOES NOT OFFER REFUNDS FOR ANY PRODUCT.
http://www.linksys.com © Copyright 2003 Linksys, All Rights Reserved.
