USER GUIDE Power Over Ethernet Adapter Kit Model No: WAPPOE
About This Guide About This Guide Icon Descriptions While reading through the User Guide you may see various icons that call attention to specific items. Below is a description of these icons: NOTE: This check mark indicates that there is a note of interest and is something that you should pay special attention to while using the product. WARNING: This exclamation point indicates that there is a caution or warning and it is something that could damage your property or product.
Table of Contents Chapter 1: Product Overview 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Splitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Chapter 2: Connection 5 Overview . . . . . . . . . . . . . . . . .
Product Overview Chapter 1 Chapter 1: Product Overview Introduction Thank you for choosing the Linksys Power Over Ethernet Adapter Kit, comprised of the Injector and Splitter. The Injector sends power and data over the Ethernet cable to the Splitter. Then the Splitter separates the data and power back into two cables and delivers them to the remotely located access point or other network device that requires a five-volt power input.
Product Overview Chapter 1 Power The Power port is where you will connect the included adapter. Ethernet IN The Injector has a built-in Ethernet network cable. You will connect this cable to one of the Ethernet network ports on your router or switch. Injector’s LED The Power LED is located on the top of the Injector. Power (Green) The Power LED lights up when the Injector is powered on and ready for use. Splitter The Splitter’s built-in cables and port are located on side panels.
Product Overview Chapter 1 Splitter’s First Side Panel The Power & Data IN port is located on the Injector’s first side panel. Power & Data IN This port allows you to connect the Splitter to the Injector. (You will use the included Ethernet network cable to make this connection.) Splitter’s Second Side Panel The built-in Ethernet network and Power cables are located on the Splitter’s second side panel. Ethernet OUT The Splitter has a built-in Ethernet network cable.
Product Overview Chapter 1 Splitter’s LED The Splitter’s LED is located on the top of the Splitter. Power (Green) The Power LED lights up when the Splitter is powered on and ready for use.
Connection Chapter 2 Chapter 2: Connection Overview This chapter gives instructions on how to connect the Power Over Ethernet Kit. Once connected, the Kit will transmit data and power over the Ethernet network cable to your remotely located network device. The diagram shows an example of how the Kit can be connected to a wired switch and a wireless access point.
Connection Chapter 2 Power on a Device that Uses a Standard Power Adapter Use the Injector and Splitter to power up a device that uses a standard power adapter. Follow these instructions: 1. Connect the Injector’s built-in Ethernet network cable to your router, switch, or other network device. 2. Connect the Kit’s included Ethernet network cable to the Injector’s Power & Data OUT port. NOTE: If this cable is not long enough, then you can use your own Ethernet network cable. 3.
Connection Chapter 2 NOTE: If the plug of the Splitter’s Power cord does not fit into your network device, then use the included barrel jack adapter. Plug the Splitter’s Power cord into the jack end, and plug the other end of the barrel jack adapter into the Power port of your network device. 6. Connect the Kit’s power adapter to the Injector, and plug the other end into an electrical outlet or surge protector. Congratulations! The installation of the Power Over Ethernet Kit is complete.
Chapter 2 Connection 3. Then connect the other end to the Ethernet port of your remotely located access point or other network device. NOTE: If the plug of the Splitter’s Power cord does not fit into your network device, then use the included barrel jack adapter. Plug the Splitter’s Power cord into the jack end, and plug the other end of the barrel jack adapter into the Power port of your network device. 4.
Specifications Appendix A Appendix A: Specifications Model WAPPOE Standards IEEE 802.3, 802.3u Ports Injector: Power, Data and Power OUT Splitter: Data and Power IN Cabling Type Category 5 or better LED Power Environmental Dimensions 3.15" x 0.87" x 2.20" (80 x 22 x 56 mm) Weight 2.65 oz. (0.075 kg) Power External Adapter: 100~240VAC, Injector 48VDC Certification FCC Class B Operating Temp. 32 to 104ºF (0 to 40ºC) Storage Temp.
Appendix A 10 10 Specifications Power Over Ethernet Adapter Kit
Warranty Information Appendix B Appendix B: Warranty Information Limited Warranty Linksys warrants this Linksys hardware product against defects in materials and workmanship under normal use for the Warranty Period, which begins on the date of purchase by the original end-user purchaser and lasts for the period specified below: • One (1) year for new product • Ninety (90) days for refurbished product This limited warranty is non-transferable and extends only to the original end-user purchaser.
Appendix B Warranty Information CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary by jurisdiction.
Regulatory Information Appendix C Appendix C: Regulatory Information FCC Statement This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix C Regulatory Information Industry Canada Statement This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: 1. This device may not cause interference and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Avis d’Industry Canada Cet appareil est conforme à la norme NMB003 d’Industrie Canada. Le fonctionnement est soumis aux conditions suivantes : 1.
Regulatory Information Appendix C English - Environmental Information for Customers in the European Union European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
Appendix C Regulatory Information Dansk (Danish) - Miljøinformation for kunder i EU EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol på produktet og/eller emballagen ikke må bortskaffes som usorteret kommunalt affald. Symbolet betyder, at dette produkt skal bortskaffes adskilt fra det almindelige husholdningsaffald. Det er dit ansvar at bortskaffe dette og andet elektrisk og elektronisk udstyr via bestemte indsamlingssteder udpeget af staten eller de lokale myndigheder.
Regulatory Information Appendix C Español (Spanish) - Información medioambiental para clientes de la Unión Europea La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Appendix C Regulatory Information Italiano (Italian) - Informazioni relative all’ambiente per i clienti residenti nell’Unione Europea La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici.
Regulatory Information Appendix C Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti fl-Unjoni Ewropea Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih is-simbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika li dan il-prodott għandu jintrema separatament minn ma’ l-iskart domestiku regolari.
Appendix C Regulatory Information Norsk (Norwegian) - Miljøinformasjon for kunder i EU EU-direktiv 2002/96/EF krever at utstyr med følgende symbol avbildet på produktet og/eller pakningen, ikke må kastes sammen med usortert avfall. Symbolet indikerer at dette produktet skal håndteres atskilt fra ordinær avfallsinnsamling for husholdningsavfall.
Regulatory Information Appendix C Română (Romanian) - Informaţii de mediu pentru clienţii din Uniunea Europeană Directiva europeană 2002/96/CE impune ca echipamentele care prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să nu fie casate împreună cu gunoiul menajer municipal. Simbolul indică faptul că acest produs trebuie să fie casat separat de gunoiul menajer obişnuit. Este responsabilitatea dvs.
Appendix C Regulatory Information Suomi (Finnish) - Ympäristöä koskevia tietoja EU-alueen asiakkaille EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä symboli itse tuotteessa ja/tai sen pakkauksessa, laitteistoa ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana. Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään tavallisesta kotitalousjätteestä.
www.linksys.
