USER GUIDE Cisco Small Business WRP400 Wireless-G Broadband Router with 2 Phone Ports
© 2009 Cisco Systems, Inc. All rights reserved.
Contents Chapter 1: Getting to Know the WRP400 9 Front Panel 9 Back Panel 12 Side Panel 13 Placement Positions 13 Chapter 2: Before You Begin: Understanding Wireless Security 16 Change the Default Wireless Network Name or SSID 16 Change the Default Router Password 17 Enable MAC Address Filtering for Wireless Access 17 Enable Encryption 17 General Network Security Guidelines 18 Additional Security Tips 18 Chapter 3: Using the Web-Based Utility for Advanced Configuration 19 How to A
Contents Chapter 5: Installing and Configuring Your Mobile Network 41 Installing Your USB Modem 42 Setup > Mobile Network 43 Setup > Connection Recovery 46 Recovery & Failover 47 WAN Interfaces 48 Understanding the LED Behavior for Mobile Network 49 LED Behavior During USB Modem Installation 49 LED Behavior During Mobile Network Connectivity 49 Chapter 6: Configuring Your Wireless Network 51 Wireless > Basic Wireless Settings 51 Manual Configuration of the Network 52 Wi-Fi Protected
Contents Chapter 8: Configuring Applications and Gaming Applications and Gaming > Single Port Forwarding 76 Applications and Gaming > Port Range Forward 77 Applications & Gaming > Port Range Triggering 79 Applications and Gaming > DMZ 80 Applications and Gaming > QoS 81 Chapter 9: Administration Administration > Management 87 88 Management 89 IGMP 91 Administration > Log 91 Administration > Diagnostics 93 Ping Test 93 Traceroute Test 94 Administration > Factory Defaults 96 Adminis
Contents Status > Local Network 106 Local Network 106 DHCP Server 106 Status > Wireless Network Chapter 11: Configuring Voice Services 108 109 Access to the Voice Screens 109 Voice > Info 110 Product Information 111 System Status 111 Line 1/2 Status 112 Voice > System 113 System Configuration 114 Miscellaneous Settings 114 Voice > User 1/2 114 Call Forward Settings 116 Selective Call Forward Settings 116 Speed Dial Settings 116 Supplementary Service Settings 117 Distinct
Contents Appendix B:Specifications 128 Appendix C:Regulatory Information 134 Appendix D:Where to Go From Here 153 Cisco WRP400 User Guide v
Preface Finding Information in PDF Files The WRP400 documents are published as PDF files. The PDF Find/Search tool within Adobe® Reader® lets you find information quickly and easily online. You can perform the following tasks: Search an individual PDF file. Search multiple PDF files at once (for example, all PDFs in a specific folder or disk drive). Perform advanced searches. Finding Text in a PDF Follow this procedure to find text in a PDF file.
Preface Finding Text in Multiple PDF Files The window lets you search for terms in multiple PDF files that are stored on your PC or local network. The PDF files do not need to be open. STEP 1 Start Acrobat Professional or Adobe Reader. STEP 2 > , or click the arrow next to the Choose Open Full Acrobat Search. STEP 3 In the box and then choose window, complete the following steps: a. Enter the text that you want to find. b. Choose . From the drop-down box, choose .
Preface STEP 4 When the Results appear, click + to open a folder, and then click any link to open the file where the search terms appear. For more information about the Find and Search functions, see the Adobe Acrobat online help.
1 Getting to Know the WRP400 Thank you for choosing the Cisco WRP400 Wireless-G Broadband Router with 2 Phone Ports. The WRP400 lets you access the Internet via a wireless connection or through one of its four switched ports. You can also use the WRP400 to share resources such as computers, printers and files. The built-in phone adapter enables Voice-over-IP (VoIP) calls even while you are using the Internet.
1 Getting to Know the WRP400 Front Panel LED Description USB: For information about supported USB devices, visit the WRP400 product page on Cisco.com: http://www.cisco.com/en/US/products/ ps10028/index.html Wi-Fi Protected Setup (White/Orange): If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup to automatically configure wireless security for your wireless network(s).
1 Getting to Know the WRP400 Front Panel LED Description Mobile network connection: If a USB modem is installed, the mobile network connection is used as a failover when an Ethernet connection is unavailable. The Power LED shows the status of the mobile network: Flashing Orange: The WRP400 is attempting to connect to the Internet through the mobile network connection. Steady Orange: The WRP400 is connected to the Internet through the mobile network connection.
1 Getting to Know the WRP400 Back Panel Back Panel Port Description Internet: Use this port to connect the WRP400 to a cable or DSL Internet connection. Phone 1-2: Use these ports to connect standard analog telephones to the WRP400. Ethernet 1, 2, 3, 4: Use these Ethernet ports to connect the WRP400 to wired computers and other Ethernet network devices. Power: Use the power port to connect the power adapter.
1 Getting to Know the WRP400 Side Panel Side Panel Reset: There are two ways to reset the WRP400 to the factory default settings. Either press and hold the Reset button for approximately ten seconds, or restore the defaults from the Administration >Factory Defaults screen of the administration web server. (The Factory Defaults screen allows you to restore the router and voice defaults separately.) NOTE: Restoring the voice defaults may require your login (the default user name and password are admin).
Getting to Know the WRP400 Placement Positions 1 Figure 1 Horizontal and Vertical Placement Options To mount the WRP400 on a wall, follow these instructions: STEP 1 Choose a wall that is smooth, flat, dry, and sturdy. Make sure that an electrical outlet is nearby. STEP 2 Obtain mounting hardware. Suggested hardware is illustrated below (not true to scale).
1 Getting to Know the WRP400 Placement Positions STEP 3 Drill two holes, 60 mm (2.36 inches) apart. Insert a screw into each hole and leave 3 mm (0.12 inches) of the head exposed. To create a template to position the screws, you can print this page at 100 percent. Then cut along the dotted line. Affix this template to the wall where you want to drill the holes. Figure 3 Wall Mount Template NOTE Cisco is not responsible for damages incurred by insecure wall-mounting hardware.
2 Before You Begin: Understanding Wireless Security Wireless networks are convenient and easy to install, so homes with high-speed Internet access are adopting them at a rapid pace. Because wireless networking operates by sending information over radio waves, it can be more vulnerable to intruders than a traditional wired network. Like signals from your cellular or cordless phones, signals from your wireless network can also be intercepted.
Before You Begin: Understanding Wireless Security Change the Default Router Password 2 Change the Default Router Password When you connect to the administration web server, you will be asked for a password. The WRP400 has a default password set by the factory. The default . Hackers know the defaults and may try to use them to access password is your wireless device and change your network settings. To prevent unauthorized access, change the password to one that is hard to guess.
Before You Begin: Understanding Wireless Security General Network Security Guidelines 2 General Network Security Guidelines Wireless network security is effective only when combined with good network security practices. Password protect all computers on the network and individually password protect sensitive files. Change passwords on a regular basis. Install anti-virus software and personal firewall software. Disable file sharing (peer-to-peer).
3 Using the Web-Based Utility for Advanced Configuration After you set up the WRP400 with the Setup Wizard (located on the CD-ROM), the router will be ready for use. However, if youd like to change its advanced settings, use the web-based utility. This chapter describes each web page of the utility and each pages key functions. You can access the utility via a web browser on a computer connected to the router.
Using the Web-Based Utility for Advanced Configuration How to Access the Web-Based Utility 3 Chapter 7, Configuring Network Security and Controlling Internet Access. Applications & Gaming: You can use the Applications and Gaming screens to configure your WRP400 to support applications, services, and gaming. For more information, see Chapter 8, Configuring Applications and Gaming.
Using the Web-Based Utility for Advanced Configuration How to Access the Web-Based Utility 3 Figure 4 Web-Based Utility Login Window Cisco WRP400 User Guide 21
4 Basic Settings On the Setup screens, you can configure general settings, such as Internet connection, IP address, DHCP server settings, DDNS, time settings, and advanced router settings. á How Do I... Change the Internet Connection type, IP address, DHCP Server settings, and other basic settings? See Setup > Basic Setup, on page 23. Set up DDNS for my web server or FTP server? See Setup > DDNS, on page 34.
4 Basic Settings Setup > Basic Setup Setup > Basic Setup You can use the Basic Setup page to configure the Internet connection and local network settings. Complete the following sections of the page: Internet Setup Network Setup Time Setting NOTE After you enter settings on this page, click click to apply your changes, or to cancel your changes. Internet Setup You can use the Internet Setup section to configure the WRP400 for your Internet connection.
4 Basic Settings Setup > Basic Setup Figure 5 Setup > Basic Setup > Internet Connection Type > Automatic Configuration - DHCP Static IP If you are required to use a permanent IP address to connect to the Internet, select . Figure 6 Setup > Basic Setup > Internet Connection Type > Static IP Enter the information that was provided by your service provider. Cisco WRP400 User Guide Internet IP Address: The IP address of your WRP400, as seen from the Internet.
4 Basic Settings Setup > Basic Setup PPPoE Some DSL-based service providers use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your service provider to see if they use PPPoE. If . they do, you will have to enable This option applies to some DSL services.
4 Basic Settings Setup > Basic Setup PPTP Point-to-Point Tunneling Protocol (PPTP) is a service that applies to connections in Europe only. Figure 8 Setup > Basic Setup > Internet Connection Type > PPTP Enter the information that was provided by your service provider, and select the Connect On Demand or Keep Alive feature, if desired. Cisco WRP400 User Guide Internet IP Address: The IP address of your WRP400, as seen from the Internet.
4 Basic Settings Setup > Basic Setup L2TP L2TP is a service that applies to connections in Europe and Israel. Figure 9 Setup > Basic Setup > Internet Connection Type > L2TP Enter the information that was provided by your service provider, and select the Connect On Demand or Keep Alive feature, if desired. Cisco WRP400 User Guide Server IP Address: The IP address of the L2TP Server. User Name and Password: The login information for your account.
4 Basic Settings Setup > Basic Setup Telstra Cable Telstra Cable is a service used in Australia only. Figure 10 Setup > Basic Setup > Internet Connection Type > Telstra Cable Enter the information that was provided by your service provider, and select the Connect On Demand or Keep Alive feature, if desired. Cisco WRP400 User Guide Heart Beat Server: The IP address of the Heart Beat Server. User Name and Password: The login information for your account.
4 Basic Settings Setup > Basic Setup Optional Settings Some of these settings may be required by your service provider. Verify with your service provider before making any changes. Figure 11 Setup > Basic Setup > Optional Settings Host Name and Domain Name: A host and domain name for the WRP400. Some service providers, usually cable service providers, require these names as identification. In most cases, leaving these fields blank will work. MTU: MTU is the Maximum Transmission Unit.
4 Basic Settings Setup > Basic Setup Network Setup You can use the Network Setup section to change the IP address of the WRP400 and configure the DHCP server settings. NOTE For wireless setup, use the Wireless tab. See Chapter 6, Configuring Your Wireless Network. Router IP You can enter the Local IP Address and Subnet Mask of the WRP400, as seen by your network.
4 Basic Settings Setup > Basic Setup Figure 13 Setup > Basic Setup > DHCP Server Setting DHCP Server: DHCP is enabled by factory default. If you already have a DHCP server on your network, or you dont want a DHCP server, then select (no other DHCP features will be available). DHCP Reservation: Click this button if you want to reserve IP addresses for clients. See DHCP Reservation, on page 32. DNS Proxy: To enable the DNS Proxy feature, select DNS Proxy feature, keep the default, . .
4 Basic Settings Setup > Basic Setup Static DNS: Enter the local IP address of the DNS server, which is provided by your service provider. If you wish to use a different DNS server, enter that IP address in this field. NOTE The Domain Name System (DNS) is how the Internet translates domain or website names into Internet addresses or URLs. WINS: If you use a WINS server, enter that servers IP address here. Otherwise, when DHCP is enabled, the field is field with the value 0.0.0.0.
4 Basic Settings Setup > Basic Setup Select Clients from DHCP Tables: To reserve an IP address for a client in the table, check the Select check box, and then click Add Clients. Manually Adding Client: To reserve an IP address for a client that is not listed in the Select Clients table, enter the Client Name, the desired IP Address, and the client MAC Address in the Manually Adding Client section. Then click Add. Clients Already Reserved: If you want to remove a client from this list, click .
4 Basic Settings Setup > DDNS Setup > DDNS You can use the DDNS page to configure the Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or other server behind the WRP400. Before you can use this feature, you need to sign up for DDNS service with a DDNS service provider, such as www.dyndns.org or www.TZO.com.
4 Basic Settings Setup > DDNS Cisco WRP400 User Guide User Name: Enter the User Name for your DDNS account. Password: Enter the Password for your DDNS account. Host Name: Enter the DDNS URL assigned by the DDNS service. System: Choose the DynDNS service you use: . The default selection is D Mail Exchange (Optional): Enter the address of your mail exchange server, so emails to your DynDNS address go to your mail server.
4 Basic Settings Setup > DDNS TZO.com Figure 17 Setup > DDNS > TZO.com Cisco WRP400 User Guide E-mail Address, TZO Key, and Domain Name: Enter the settings for your account with TZO. Internet IP Address: The Internet IP address of the WRP400 is displayed here. Because it is dynamic, it will change. Status: The status of the DDNS service connection is displayed here. Update: To manually trigger an update, click this button.
4 Basic Settings Setup > MAC Address Clone Setup > MAC Address Clone A MAC address is a unique 12-digit code that is assigned to a piece of hardware for identification. Some service providers require you to register a MAC address in order to access the Internet. If you previously registered a MAC address with your service provider for this purpose, you can reassign that MAC address to the WRP400. In this sense, you are cloning the MAC address to be used by this router.
4 Basic Settings Setup > Advanced Routing Setup > Advanced Routing You can use the Advanced Routing page to set up PPPoE Relay, NAT, Dynamic Routing (RIP), or Static Routing. NOTE After you enter settings on this page, click click to apply your changes, or to cancel your changes.
4 Basic Settings Setup > Advanced Routing Advanced Settings: PPPoE Relay The PPPoE Relay feature enables an L2TP Access Concentrator (LAC) to relay active discovery and service selection functionality for PPP over Ethernet (PPPoE), over a Layer 2 Tunneling Protocol (L2TP) control channel, to an L2TP Network Server (LNS) or tunnel switch (multihop node).
4 Basic Settings Setup > Advanced Routing - Subnet Mask: The Subnet Mask determines which portion of a Destination LAN IP address is the network portion, and which portion is the host portion. - Gateway: This is the IP address of the gateway device that allows for contact between the WRP400 and the remote network or host. - Interface: This interface tells you whether the Destination LAN IP (Ethernet and wireless networks) or address is on the .
5 Installing and Configuring Your Mobile Network You can connect a Mobile Broadband USB modem to the USB port of the WRP400 and configure the mobile network connection. á Cisco WRP400 User Guide How Do I...
Installing and Configuring Your Mobile Network Installing Your USB Modem 5 Installing Your USB Modem You can install a supported Mobile Broadband USB Modem into the USB port of the WRP400 for the purpose of accessing a mobile network. NOTE For more information about supported USB devices, visit the WRP400 product page on Cisco.com: http://www.cisco.com/en/US/products/ps10028/index.html Connect a supported USB Modem into the USB port of the WRP400.
Installing and Configuring Your Mobile Network Setup > Mobile Network 5 Setup > Mobile Network You can use this page to choose the connect mode and to enter the settings for the mobile network. You also can use this page to view the current connection status. NOTE After you enter settings on this page, click click to apply your changes, or to cancel your changes.
Installing and Configuring Your Mobile Network Setup > Mobile Network 5 Connect Mode: - Select Auto to enable your modem to establish connection automatically. - Select Manual to connect or disconnect your modem connection manually. - If you change your selection from Auto to Manual, a message appears. Click OK to acknowledge that Connection Recover will be disabled, or click Cancel to cancel. - If you change your selection from Manual to Auto, a message appears.
Installing and Configuring Your Mobile Network Setup > Mobile Network Cisco WRP400 User Guide 5 Card Model: The data card model that is inserted in the USB port. Carrier: The mobile network service provider for Internet connection. This setting is required when you are using HSDPA/UMTS/GPRS Internet service. Country: Select the card issue country from the first drop-down menu. Carrier: Select the card issue provider from the second drop-down menu.
Installing and Configuring Your Mobile Network Setup > Connection Recovery 5 Setup > Connection Recovery An Internet connection can be established via the Ethernet Internet port or a USB modem connected to the USB port. While both Ethernet and USB interfaces may be connected, only one of them can be used to establish a link at a time. By default, the WRP400 uses the Ethernet Internet connection when available.
Installing and Configuring Your Mobile Network Setup > Connection Recovery 5 Recovery & Failover Ethernet Connection Recovery: This feature ensures that your Internet connection is made through the Ethernet interface if it is available. Enabling this feature also enables the Interface Connection Failover, which ensures that if the Internet connection fails on the Ethernet interface, the WRP400 automatically attempts to bring up the connection through the mobile network if available.
Installing and Configuring Your Mobile Network Setup > Connection Recovery 5 WAN Interfaces The Summary table includes one row of information for the Ethernet interface and one row of information for the USB interface. Status: The link status of this interface: - Disconnected: The device is plugged in and available but not active. - Connecting: The WRP400 is attempting to bring up the link over the device. - Connected: The link is up and running on the device.
Installing and Configuring Your Mobile Network Understanding the LED Behavior for Mobile Network 5 Understanding the LED Behavior for Mobile Network The Internet LED indicates connectivity to the Internet through the Ethernet connection only. The Power LED indicates the progress of USB initialization or the status of the mobile network connection. LED Behavior During USB Modem Installation The Power LED indicates the progress of the initialization.
Installing and Configuring Your Mobile Network Understanding the LED Behavior for Mobile Network - 5 If the USB device was removed, this LED behavior indicates that the WRP400 has power. To check the status of the USB Modem, or modify the settings for the mobile network, connection recovery, and failover, you can use the administration web server.
6 Configuring Your Wireless Network You can use the Wireless screens to set up and secure your wireless network. á How Do I... Set up my wireless network? See Wireless > Basic Wireless Settings, on page 51. Secure my wireless network? See Wireless > Wireless Security, on page 56.
Configuring Your Wireless Network Wireless > Basic Wireless Settings 6 The options on the page change after you choose Manual or Wi-Fi Protected Setup. Choose Manual if you want to manually configure your network, if you are setting up your secondary network (SSID2), of if you do not have client devices that support Wi-Fi Protected Setup. See Manual Configuration of the Network, on page 52.
6 Configuring Your Wireless Network Wireless > Basic Wireless Settings SSID1, SSID2: The SSID is the network name shared among all devices in a wireless network. The WRP400 can support up to two wireless networks. By default, one wireless network is enabled, and you can create a second wireless network.
6 Configuring Your Wireless Network Wireless > Basic Wireless Settings Wi-Fi Protected Setup After you choose Wi-Fi Protected Setup for the Wireless Configuration, the instructions, fields, and buttons appear on the screen. Three setup methods are available. NOTE Wi-Fi Protected Setup is available for your primary wireless network (SSID1) only. To configure your second wireless network (SSID2), .
Configuring Your Wireless Network Wireless > Basic Wireless Settings Cisco WRP400 User Guide 6 - Method #1: To configure a client device that has a Wi-Fi Protected button on the Setup button, click or press the client device. Then click the button shown on the screen. After the client device has been configured, click . Then refer to your client device or its documentation for further instructions. Repeat for any additional devices that you need to configure.
6 Configuring Your Wireless Network Wireless > Wireless Security - Method #3: If your client device asks for the PIN number of the WRP400, enter the PIN number that is shown on the screen. This number also appears on the label on the bottom of the WRP400. After the client . Then refer to your client device or device has been configured, click its documentation for further instructions. Repeat for any additional devices that you need to configure.
6 Configuring Your Wireless Network Wireless > Wireless Security Figure 25 Wireless > Wireless Security NOTE If you enabled the second wireless network on the Basic Wireless Settings screen, you will need to set up wireless security for each SSID. Depending on the selected Security Mode, additional fields appear. WEP WEP is a basic encryption method, which is not as secure as WPA Figure 26 Wireless Security > WEP Cisco WRP400 User Guide Encryption: Select a level of WEP encryption, .
Configuring Your Wireless Network Wireless > Wireless Security 6 Passphrase: Enter a Passphrase to automatically generate WEP keys. Then click . Key 1-4: If you did not enter a Passphrase, enter the WEP key(s) manually. TX Key: Select which TX (Transmit) Key to use. The default is . WPA Personal Wi-Fi Protected Access (WPA) is a security mode that uses a shared key to restrict access to authorized users.
Configuring Your Wireless Network Wireless > Wireless Security 6 WPA2 Personal Like WPA Personal, WPA2 Personal uses a shared key to restrict access to your wireless network. WPA2 can combine TKIP and AES encryption. Figure 28 Wireless Security > WPA2 Personal Cisco WRP400 User Guide WPA Algorithms: WPA2 supports two encryption methods, TKIP and AES, or with dynamic encryption keys. Select the type of algorithm, . The default is . WPA Shared Key: Enter a WPA Shared Key of 8-63 characters.
Configuring Your Wireless Network Wireless > Wireless Security 6 WPA Enterprise This option features WPA used in coordination with a RADIUS (Remote Authentication Dial-In User Service) server. This option should only be used when a RADIUS server is connected to the WRP400. Figure 29 Wireless Security > WPA Enterprise Cisco WRP400 User Guide WPA Algorithms: WPA supports two encryption methods, TKIP and AES, or . with dynamic encryption keys. Select the type of algorithm, The default is .
Configuring Your Wireless Network Wireless > Wireless Security 6 WPA2 Enterprise This option features WPA2 used in coordination with a RADIUS (Remote Authentication Dial-In User Service) server. This option should only be used when a RADIUS server is connected to the WRP400. Figure 30 Wireless > Wireless Security > WPA2Enterprise Cisco WRP400 User Guide WPA Algorithms: WPA2 supports two encryption methods, TKIP and AES, or with dynamic encryption keys. Select the type of algorithm, . The default is .
6 Configuring Your Wireless Network Wireless > Wireless MAC Filter Wireless > Wireless MAC Filter Wireless access can be filtered by using the MAC addresses of the wireless devices within your networks radius. NOTE After you enter settings on this page, click click to apply your changes, or to cancel your changes. Figure 31 Wireless > Wireless MAC Filter Select a SSID: Select the SSID that you want to configure.
6 Configuring Your Wireless Network Wireless > Wireless MAC Filter Wireless MAC Filter: To filter wireless users by MAC address, select If you do not wish to filter users by MAC address, keep the default setting, . Access Restriction In this section, you choose how to use the MAC Address Filter List: to prevent access or to permit access. Prevent: Select this option to block wireless access to devices with the specified MAC addresses. This button is selected by default.
6 Configuring Your Wireless Network Wireless > Advanced Wireless Settings Figure 32 Wireless Client List Wireless > Advanced Wireless Settings The Advanced Wireless Settings screen is used to set up the advanced wireless functions of the WRP400. These settings should only be adjusted by an expert administrator as incorrect settings can reduce wireless performance. NOTE After you enter settings on this page, click click to apply your changes, or to cancel your changes.
Configuring Your Wireless Network Wireless > Advanced Wireless Settings Cisco WRP400 User Guide 6 Authentication Type: The default is set to , which allows either Open System or Shared Key authentication to be used. With Open System authentication, the sender and the recipient do not use a WEP key for authentication. With Shared Key authentication, the sender and recipient to only use Shared use a WEP key for authentication. Select Key authentication.
7 Configuring Network Security and Controlling Internet Access You can use the Security screens to enable a firewall, add filters, or allow VPN tunnels. You can use the Access Restrictions screen to control Internet usage. á How Do I...
Configuring Network Security and Controlling Internet Access Security > Firewall 7 Figure 34 Security > Firewall Firewall SPI Firewall Protection: To use firewall protection, keep the default, . To turn off firewall protection, select . Internet Filter Cisco WRP400 User Guide This feature makes it more difficult for outside users to work their way into your network. This feature is selected by default. Deselect the feature to allow anonymous Internet requests.
Configuring Network Security and Controlling Internet Access Security > VPN Passthrough 7 Web Filter Proxy: Use of WAN proxy servers may compromise the security of the WRP400. Denying Proxy will disable access to any WAN proxy servers. Select this feature to enable proxy filtering. Deselect the feature to allow proxy access. Java: Java is a programming language for websites. If you deny Java, you run the risk of not having access to Internet sites created using this programming language.
Configuring Network Security and Controlling Internet Access Access Restrictions > Internet Access 7 IPSec Passthrough: Internet Protocol Security (IPSec) is a suite of protocols used to implement secure exchange of packets at the IP layer. To allow IPSec tunnels to pass through the WRP400, keep the default, . PPTP: Passthrough Point-to-Point Tunneling Protocol (PPTP) allows the Point-to-Point Protocol (PPP) to be tunneled through an IP network. To allow .
Configuring Network Security and Controlling Internet Access Access Restrictions > Internet Access 7 Figure 36 Access Restrictions > Internet Access Cisco WRP400 User Guide Access Policy: Select a policy from the drop-down list to display that policys settings. You can then enter or modify the settings. Be sure to save your changes before selecting another policy from the drop-down list.
Configuring Network Security and Controlling Internet Access Access Restrictions > Internet Access Cisco WRP400 User Guide 7 Delete This Entry: To delete an access policy, select the policys number from the Access Policy list, and then click this button. Summary: To view all policies, click this button. The Summary appears in a separate window. The policies are listed with the following information: No. (number), Policy Name, Access, Days, Time of Day, and status (Enabled). To .
Configuring Network Security and Controlling Internet Access Access Restrictions > Internet Access 7 Applied PCs: Click Edit List to select the computers that will be affected by the policy that you selected in the Access Policy list. The List of PCs window appears. Choose the PCs that will be affected by this policy: - MAC Address: Enter a MAC address that you want to add to the list. - IP Address: Enter the final octet of an IP address that you want to add to the list.
Configuring Network Security and Controlling Internet Access Access Restrictions > Internet Access 7 Schedule: Decide which days and what times you want the selected policy to be enforced. Select the individual days during which the policy will be in effect, or select Everyday. Then enter a range of hours and minutes during which the policy will be in effect, or select 24 Hours. Website Blocking by URL Address: You can block websites with specific URL addresses.
Configuring Network Security and Controlling Internet Access Access Restrictions > Internet Access 7 STEP 5 In the Access Restriction section, choose to Deny Internet access or to Allow Internet access for the computers that you listed on the List of PCs screen. STEP 6 In the Schedule section, select the days and times when this policy applies, as described above.
8 Configuring Applications and Gaming You can use the Applications and Gaming screens to configure your WRP400 to support applications, services, and gaming. á Cisco WRP400 User Guide How Do I... Customize port services for common applications? See Applications and Gaming > Single Port Forwarding, on page 76. Support public services such as web servers, FTP servers, e-mail servers, and Internet gaming? See Applications and Gaming > Port Range Forward, on page 77.
8 Configuring Applications and Gaming Applications and Gaming > Single Port Forwarding Applications and Gaming > Single Port Forwarding The Single Port Forwarding screen allows you to customize port services for common applications on this screen. When users send these types of requests to your network via the Internet, the WRP400 will forward those requests to the appropriate servers (computers).
8 Configuring Applications and Gaming Applications and Gaming > Port Range Forward For additional applications, complete the following fields: Application Name: Enter the name you wish to give the application. Each name can be up to 12 characters. External Port: Enter the external port number used by the server or Internet application. Check with the Internet application documentation for more information. Internal Port: Enter the internal port number used by the server or Internet application.
8 Configuring Applications and Gaming Applications and Gaming > Port Range Forward NOTE After you enter settings on this page, click click to apply your changes, or to cancel your changes. Figure 38 Applications and Gaming > Port Range Forwarding To forward a port, enter the information on each line for the criteria required. Cisco WRP400 User Guide Application Name: In this field, enter the name you wish to give the application. Each name can be up to 12 characters.
8 Configuring Applications and Gaming Applications & Gaming > Port Range Triggering Applications & Gaming > Port Range Triggering The Port Range Triggering screen allows the WRP400 to watch outgoing data for specific port numbers. The IP address of the computer that sends the matching data is remembered by the WRP400, so that when the requested data returns through the WRP400, the data is pulled back to the proper computer by way of IP address and port mapping rules.
8 Configuring Applications and Gaming Applications and Gaming > DMZ Applications and Gaming > DMZ The DMZ feature allows one network computer to be exposed to the Internet for use of a special-purpose service such as Internet gaming or videoconferencing. DMZ hosting forwards all the ports at the same time to one PC.
8 Configuring Applications and Gaming Applications and Gaming > QoS Destination: If you want to specify the DMZ host by IP address, select and enter the IP address in the field provided. If you want to specify the DMZ host by MAC address, select and enter the MAC address in the field provided. DHCP Client Table: Click this button to view a list of DHCP clients. See DHCP Client Table. This button becomes available when you select the MAC Address option.
Configuring Applications and Gaming Applications and Gaming > QoS 8 Figure 41 Applications and Gaming > QoS Wireless Cisco WRP400 User Guide WMM Support: If you have other devices that support Wi-Fi Multimedia (WMM) on your network, select E . Otherwise, keep the default, . No Acknowledgement: To prevent the WRP400 from resending data if an error occurs, select . Otherwise, keep the default, .
8 Configuring Applications and Gaming Applications and Gaming > QoS Internet Access Priority In this section, you can set the bandwidth priority for a variety of applications and devices. There are four levels priority: High, Medium, Normal, or Low. When you set priority, do not set all applications to High, because this will defeat the purpose of allocating the available bandwidth. If you want to select below normal bandwidth, select Low.
8 Configuring Applications and Gaming Applications and Gaming > QoS - Enter a Name: Enter any name to indicate the name of the entry. - Port Range: Enter the port range in the text boxes, and choose a protocol: , , or . You can have up to three ranges to define for this bandwidth allocation. Port numbers can range from 1 to 65535. Check your applications documentation for details on the service ports used. - Priority: Select the appropriate priority: , or L . - Click Add to save your changes.
8 Configuring Applications and Gaming Applications and Gaming > QoS - Click Add to save your changes. Your new entry will appear in the Summary list. MAC Address Enter a Name: Enter a name for the device. MAC Address: Enter the MAC address of the device. Priority: Select the appropriate priority: N , or . , , : Click this button to add your new entry to the Summary list. Ethernet Port Ethernet: Select the appropriate Ethernet port.
Configuring Applications and Gaming Applications and Gaming > QoS 8 Summary The Summary table lists the QoS entries that you have created for your applications and devices. Cisco WRP400 User Guide Priority: This column displays the bandwidth priority of High, Medium, Normal, or Low. Name: This column displays the application, device, or port name. Information: This column displays the port range or MAC address entered for your entry.
9 Administration You can use the Administration screens to manage access, configure Universal Plug and Play, support multimedia streaming, enable logging and diagnostics, restore factory default settings, upgrade firmware, and back up and restore configurations. á Cisco WRP400 User Guide How Do I... Change the admin password? See Administration > Management, on page 88. Enable remote management of my network? See Administration > Management, on page 88.
9 Administration Administration > Management Administration > Management You can use the Administration > Management screen to change the password, to manage access, to enable remote management, to configure UPnP (Universal Plug and Play), and to enable support for multimedia streaming. NOTE After you enter settings on this page, click click to apply your changes, or to cancel your changes.
9 Administration Administration > Management Management Router Access Use this section of the page to enter a password to prevent unauthorized access to the web-based utility, you will be asked for your password when you access . the web-based utility of the WRP400. The default is Router Password: Enter a new password for the WRP400. Re-enter to Confirm: Enter the password again to confirm.
9 Administration Administration > Management Remote Management Port: Enter the port number that will be open to outside access.
9 Administration Administration > Log IGMP Internet Group Multicast Protocol (IGMP) is used to establish membership in a multicast group and is commonly used for multicast streaming applications. For example, you may have Internet Protocol Television (IPTV) with multiple setup boxes on the same local network. These setup boxes have different video streams running simultaneously, so you should use the IGMP feature of the WRP400. , Support IGMP Version: Select the version you want to support, , or .
9 Administration Administration > Log View Log: To view the logs, click . Figure 44 Log > View Log Type: Select . The Incoming Log will display a temporary log of the source IP addresses and destination port numbers for the incoming Internet traffic. The Outgoing Log will display a temporary log of the local IP addresses, destination URLs/IP addresses, and service/port numbers for the outgoing Internet traffic.
9 Administration Administration > Diagnostics Administration > Diagnostics The diagnostic tests (Ping, Traceroute, and Detect Active LAN Clients) allow you to check the connections of your network devices, including connection to the Internet. Figure 45 Administration > Diagnostics Ping Test The Ping test checks the status of a connection. Cisco WRP400 User Guide IP or URL Address: Enter the address of the PC whose connection you wish to test. Packet Size: Enter the packet size you want to use.
9 Administration Administration > Diagnostics Figure 46 Diagnostics > Ping Traceroute Test The Traceroute test tests the performance of a connection. Cisco WRP400 User Guide IP or URL Address: Enter the address of the PC whose connection you wish to test. Start to Traceroute: To run the test, click this button. The Traceroute Test screen will show if the test was successful. Click to return to the Diagnostics screen.
9 Administration Administration > Diagnostics Figure 47 Diagnostics > Traceroute Detect Active LAN Client(s) Search Time: Select how many seconds you wish to perform this search: , , or . Start to Search: To run the search, click this button. The Active LAN Client Table screen will show the search results. You can sort the results by IP Address, MAC Address, Interface, Client Name, or IP Status. To re-run the search, click Cisco WRP400 User Guide . Click to return to the Diagnostics screen.
9 Administration Administration > Factory Defaults Figure 48 Diagnostics > Active LAN Client Table Administration > Factory Defaults The Administration > Factory Defaults screen allows you to restore the default configuration to the router settings and/or voice settings. NOTE After you enter settings on this page, click click to apply your changes, or to cancel your changes. Figure 49 Administration > Factory Defaults NOTE Restoring factory defaults deletes custom settings.
9 Administration Administration > Firmware Upgrade Restore Voice Factory Defaults: To reset the voice settings to the default values, select . Then click . Any custom Voice settings you have saved will be lost when the default settings are restored. NOTE Restoring the voice defaults may require your login (the default user name and password are more information. ).
9 Administration Administration > Firmware Upgrade NOTE The WRP400 may lose the settings you have customized. Before you upgrade the firmware, use the Config Management screen to back up your settings. For more informaiton, see Administration > Config Management, on page 99. Firmware Upgrade Download the latest firmware from Cisco.com, and then upgrade the firmware on your WRP400. Downloading the Firmware STEP 1 Go to the WRP400 product page on Cisco.com: http://www.cisco.
Administration Administration > Config Management 9 Firmware Upgrade After you download the firmware from Cisco.com, you can upgrade the WRP400. Figure 51 Administration > Firmware Upgrade Please select a file to upgrade the firmware: Click and select the firmware upgrade file that you downloaded from Cisco.com. Start to Upgrade: After you have selected the appropriate file, click this button, and follow the on-screen instructions.
9 Administration Administration > Reboot Backup Configuration Backup: To save the settings in a configuration file, click this button and follow the on-screen instructions. Restore Configuration To use this option, you must have previously backed up its configuration settings. Please select a file to restore: Click the configuration file. Restore: To restore the configuration settings, click this button and follow the on-screen instructions.
10 Using the Status Screens You can use the Status screens to view information about your WRP400. á Cisco WRP400 User Guide How Do I... View the firmware version, the router name, the host name, the Internet MAC address and the current time? See Status > Router, on page 102. View the status of the Internet connection? See Internet Connection, on page 103.
10 Using the Status Screens Status > Router Status > Router The Router screen displays information about the WRP400. Figure 54 Status > Router Router Information Cisco WRP400 User Guide Firmware Version: The version number of the current firmware is displayed. Current Time: The time set on the WRP400 is displayed.
10 Using the Status Screens Status > Router Internet MAC Address: The MAC address, as seen by your service provider, is displayed. Router Name: The name of the WRP400 is displayed. Host Name: If required by your service provider, this was entered on the Basic Setup screen. Domain Name: If required by your service provider, this was entered on the Basic Setup screen. Internet Connection This section shows the current network information.
10 Using the Status Screens Status > Mobile Network Status > Mobile Network The Mobile Network Status screen shows the status of the mobile network and displays information about the data card. The screen automatically refreshes periodically.
10 Using the Status Screens Status > Mobile Network Data Card Status : The manufacturer of the Mobile USB modem data card : The model number of your Mobile USB modem data card : The firmware that is installed on your Mobile USB modem data card Cisco WRP400 User Guide : The status of your SIM card : International Mobile Subscriber Identity is a unique number that is stored in the Subscriber Identity Module (SIM) associated with all GSM and Universal Mobile Telecommunications System (UMTS)
10 Using the Status Screens Status > Local Network Status > Local Network The Local Network screen displays information about the local, wired network. Figure 56 Status > Local Network Local Network Local MAC Address: The MAC address of the local, wired interface of the WRP400 is displayed. Router IP Address: The IP address of the WRP400, as it appears on your local network, is displayed. Subnet Mask: The Subnet Mask of the WRP400 is displayed.
Using the Status Screens Status > Local Network 10 Figure 57 DHCP Clients Table DHCP Client Table The DHCP Client Table lists computers and other devices that have been assigned IP addresses by the WRP400. The list can be sorted by Client Name, IP Address, Interface, MAC Address, and Expires Time (how much time is left for the current IP . To retrieve the most up-to-date address). To remove a DHCP client, click information, click . To exit this screen and return to the Local Network .
10 Using the Status Screens Status > Wireless Network Status > Wireless Network The Wireless Network screen displays information about your wireless network(s). Figure 58 Status > Wireless Network Channel: The channel of the wireless network(s) is displayed. Mode: The wireless mode is displayed. Status information for each wireless network is displayed. Cisco WRP400 User Guide Wireless MAC Address: The wireless MAC address of the local, wireless interface is displayed.
11 Configuring Voice Services You can use the Voice screens to manage the voice gateway features of the WRP400. á How Do I...
Configuring Voice Services Voice > Info 11 NOTE In most cases, you do not need to use the administrative screens. Contact your service provider for more information. Voice > Info The Info screen displays Voice over Internet Protocol (VoIP) information about the WRP400.
11 Configuring Voice Services Voice > Info Product Information Product Name: The model number of the WRP400 Serial Number: The serial number of the WRP400 Software Version: The version number of the WRP400 software Hardware Version: The version number of the WRP400 hardware MAC Address: The MAC address of the WRP400 Client Certificate: The status of the client certificate, which indicates that the WRP400 has been authorized by your service provider, System Status Cisco WRP400 User
11 Configuring Voice Services Voice > Info Line 1/2 Status Lines 1 and 2 have the same status information available. Hook State: The status of the Internet phone lines readiness. On indicates that it is ready for use, while Off indicates that it is in use. Registration State: The status of the lines registration with the service provider Last Registration At: The last date and time the line was registered are displayed.
11 Configuring Voice Services Voice > System Call 1/2 Packets Sent: The number of packets sent Call 1/2 Packets Recv: The number of packets received Call 1/2 Bytes Sent: The number of bytes sent Call 1/2 Bytes Recv: The number of bytes received Call 1/2 Decode Latency: The number of milliseconds for decoder latency Call 1/2 Jitter: The number of milliseconds for receiver jitter Call 1/2 Round Trip Delay: The number of milliseconds for delay Call 1/2 Packets Lost: The number
11 Configuring Voice Services Voice > User 1/2 System Configuration User Password: Enter the password for user access to the Voice screens. (By default, there is no password.) Miscellaneous Settings No settings are displayed. Voice > User 1/2 The User 1 and 2 screens display similar settings. The User 1 screen displays settings for users of phone line 1, and the User 2 screen displays settings for users of phone line 2.
Configuring Voice Services Voice > User 1/2 11 Figure 61 Voice > User 1 Cisco WRP400 User Guide 115
11 Configuring Voice Services Voice > User 1/2 Call Forward Settings Enter the call forwarding numbers you want to use. Cfwd All Dest: Enter the number for the Call Forward All Service feature (when you want to forward all calls). Cfwd Busy Dest: Enter the number for the Call Forward Busy feature (when the line is busy). Cfwd No Ans Dest: Enter the number for the Call Forward No Answer feature (when the line is not answered).
11 Configuring Voice Services Voice > User 1/2 Supplementary Service Settings CW Setting: Select whether you want to use the Call Waiting feature for all or . The default is . calls, Block CID Setting: Select whether you want to block Caller ID for all calls, or . The default is . Block ANC Setting: Select whether you want to block anonymous calls, or . The default is . DND Setting: Select whether you want to use the Do Not Disturb (DND) feature, Y or . The default is .
11 Configuring Voice Services Voice > Admin Login Cblk Ring Splash Len: Enter the duration of the ring splash when a call is blocked. The range is 0 to 10.0 seconds. The default is . VMWI Ring Splash Len: Enter the duration of the ring splash when new messages arrive before the VoiceMail Waiting Indication (VMWI) signal is applied. The range is 0 to 10.0 seconds. The default is . Click changes.
12 Interactive Voice Response Menu Overview This chapter explains how to use the Interactive Voice Response (IVR) Menu to configure the network settings. Use your telephones keypad to enter your commands and select choices, and the WRP400 will use voice responses. To access the IVR Menu: STEP 1 Use a telephone connected to the Phone 1 or 2 port of the WRP400. (You can only access the IVR Menu through an analog telephone, not any of the Internet phones.
12 Interactive Voice Response Menu Menu Commands Action Command Enter IVR Menu **** Use this command to enter the IVR Menu. Ignore Special Information Tones (SITs) or other tones until you hear, Configuration menu. Please enter the option followed by the # (pound) key, or hang up to exit. Check DHCP 100 The IVR announces whether DHCP is enabled or disabled. Check IP Address 110 The IVR announces the current IP address of the WRP400.
A Troubleshooting NOTE If your questions are not addressed here, refer to the Application Notes and other Technical Resources on Cisco Partner Central website for Voice and Conferencing, at the following URL: http://www.cisco.com/web/partners/sell/smb/products/ voice_and_conferencing.html This chapter has two sections: General Troubleshooting, on page 121 Mobile Network Troubleshooting, on page 125 General Troubleshooting Q. My computer cannot connect to the Internet.
A Troubleshooting Q. There is no dial tone, and the Phone 1 or 2 LED is not lit. Follow these instructions until your problem is solved: a. Make sure the telephone is plugged into the appropriate port, Phone 1 or 2. b. Disconnect and re-connect the RJ-11 telephone cable between the WRP400 and telephone. c. Make sure your telephone is set to its tone setting (not pulse). d. Make sure your network has an active Internet connection.
A Troubleshooting Q. The modem does not have an Ethernet port. If your modem does not have an Ethernet port, then it is a modem for traditional dial-up service. To use the WRP400, you need a cable/DSL modem and a high-speed Internet connection. Q. I cannot use the DSL service to connect manually to the Internet.
A Troubleshooting Q. I need to modify the settings on the WRP400. To access the web-based utility, follow these instructions: a. Launch the web browser on your computer, and enter the default IP address of the WRP400, , in the field. Then press . NOTE If you place the WRP400 behind a primary router with the IP address of 192.168.15.1, then the WRP400 will automatically assume a new default IP address, . b. A login screen appears. The first time you open the web-based utility, .
A Troubleshooting Mobile Network Troubleshooting Q. What do I do if the WRP400 does not recognize my USB device? a. Make sure that you have the latest mobile-support firmware loaded on your WRP400. To download the latest firmware, go to the WRP400 product page on www.cisco.com/en/US/products/ps10028/index.html b. Make sure that your USB device is on the list of supported Mobile Broadband USB Modems. For more information, visit the WRP400 product page on www.cisco.com/en/US/products/ps10028/index.html c.
A Troubleshooting b. Make sure that your USB device is on the list of supported Mobile Broadband USB Modems. For more information, visit the WRP400 product page on www.cisco.com/en/US/products/ps10028/index.html c. If you're installing a Mobile Broadband USB modem, make sure that your modem is activated with a data service, and verify that it can be used on your computer. d. Some mobile network service providers require that you enter specific information such as APN, Dial Number, User Name, and Password.
A Troubleshooting on to the WRP400 web-based utility and use the Setup tab > Mobile Network page and the Setup tab > Ethernet Recovery page. For more information, see Setup > Mobile Network, on page 43 and Setup > Connection Recovery, on page 46. Q. How do you know which mobile network you are using? Follow these instructions: a. Open a web browser. b. Enter the IP address of the WRP400 in the Address field (the default IP address is 192.168.15.1). Then press Enter. c.
B Specifications Data Networking MAC Address (IEEE 802.
B Specifications Voice Features Voice Algorithms G.711 (a-law and -Law) G.726 (16/24/32/40 kbps) G.729 AB Call Forwarding: No Answer/Busy/Unconditional Support for two simultaneous calls, including G.
B Specifications Voice RFCs Compliance continued RFC 3264 (SDP Answer and Offer) RFC 3265 (SIP Specific Event Notification) RFC 3550 (RTP: Real Time Protocol) RFC 3551 (RTP: Real Time Protocol for AVP) RFC 2327 (SDP: Session Description Protocol) RFC 3428 (SIP Extensions for Instant Messaging) RFC 3515 (SIP Refer) RFC 3581 (SIP Extensions for Symmetric Response Routing) RFC 3842 (SIP Message Summary and Message Waiting Indication) RFC 3856 (SIP Presence Event Package) RFC 3891 (SIP "Replaces" Header) RFC
B Specifications Voice RFCs Compliance continued RFC 2396 (URI : Generic Identifier) Draft-ieft-mmusic-media-loopback-04.txt (Media Loopback) Draft-ietf-sip-privacy-04.
B Specifications Detachable Antenna No RF Pwr (EIRP) in dBm Average, not including antenna: 802.11g: Typ. 18 dBm @ Normal Temp Range(with PA) 802.11b: Typ: 20 dBm @ Normal Temp Range (with PA)" Antenna Gain in 2 dBi dBi UPnP able/cert Yes Power Supply Switching Type (100-240v) Automatic DC Input Voltage: +5 VDC at 2.0 A Max. Power Consumption: 7.9 WATTs (Average) Power Adapter: 100-240v - 50-60Hz (26-34VA) AC Input, 1.
B Specifications Operating Temperature 0° C to 40° C (32° F to 104° F) Storage Temperature -20° C to 60° C (-4° F to 140° F) Operating Humidity 10% to 85% relative humidity, Non-Condensing Storage Humidity 5% to 90% Non-Condensing NOTE Many specifications are programmable within a defined range or list of options. Please see the ATA Administration Guide for details. The target configuration profile is uploaded to the WRP400 at the time of provisioning.
C Regulatory Information This appendix includes the following regulatory statements: Federal Communications Commission Interference Statement, on page 134 Safety Notices and Information, on page 136 Industry Canada Statement, on page 137 Avis dIndustrie Canada, on page 138 Telepermit Statement, on page 139 Statement 287Declaration of Conformity to R&TTE Directive 1999/ 5/EC for the European Community, Switzerland, Norway, Iceland and Liechtenstein, on page 139 CE M
C Regulatory Information This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications.
C Regulatory Information Safety Notices and Information ÿ CAUTION: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord. Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. WARNING: This product contains lead, known to the State of California to cause cancer, and birth defects or other reproductive harm.
C Regulatory Information WARNING: To ensure compliance with explosure limits to radiofrequency fields, the antenna of the WRP400 should be no closer than 20 cm from the body during use. Industry Canada Statement This device complies with Industry Canada ICES-003 rule. Operation is subject to the following two conditions: 1. This device may not cause interference and 2. This device must accept any interference, including interference that may cause undesired operation of the device.
C Regulatory Information This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Avis dIndustrie Canada Cet appareil numérique de la classe B est conforme aux normes NMB-003 et RSS210 du Canada. Lutilisation de ce dispositif est autorisée seulement aux conditions suivantes : 1. il ne doit pas produire de brouillage et 2.
C Regulatory Information Avis de non-responsabilité concernant les appareils sans fil Les performances maximales pour les réseaux sans fil sont tirées des spécifications de la norme IEEE 802.11. Les performances réelles peuvent varier, notamment en fonction de la capacité du réseau sans fil, du débit de la transmission de données, de la portée et de la couverture.
Regulatory Information Cisco WRP400 User Guide C 140
Regulatory Information C Latviski Malti Magyar Polski Cisco WRP400 User Guide 141
C Regulatory Information Suomi Svenska For all products, the Declaration of Conformity (DofC) is available through one or more of these options: A pdf file is included on the products CD. A print copy is included with the product. A pdf file is available on the products webpage. Visit www.cisco.com/go/ smallbusiness. If you need any other technical documentation, see Appendix E, Additional Information..
C Regulatory Information or or or Check the CE label on the product to find out which notified body was involved during the assessment.
C Regulatory Information The requirements for any country may evolve. Cisco recommends that you check with the local authorities for the latest status of their national regulations for both the 2,4- and 5-GHz wireless LANs. Table 1 Overview of Regulatory Requirements for Wireless LANs Frequency Band (MHz) Max Power Level (EIRP) (mW) 2400-2483.
C Regulatory Information Table 2 Applicable Power Levels in France Location Frequency Range (MHz) Power (EIRP) Indoor (No restrictions) 2400-2483.5 100 mW (20 dBm) Outdoor 2400-2454 2454-2483.5 100 mW (20 dBm) 10 mW (10 dBm) Italy This product meets the National Radio Interface and the requirements specified in the National Frequency Allocation Table for Italy.
C Regulatory Information Product Usage Restrictions This product is designed for indoor usage only. Outdoor usage is not recommended, unless otherwise noted. 2,4 GHz Restrictions This product is designed for use with the standard, integral or dedicated (external) antenna(s) that is/are shipped together with the equipment. However, some applications may require the antenna(s), if removable, to be separated from the product and installed remotely from the device by using extension cables.
C Regulatory Information Û²¹´·-¸ ó Û²ª·®±²³»²¬¿´ ײº±®³¿¬·±² º±® Ý«-¬±³»®- ·² ¬¸» Û«®±°»¿² ˲·±² Û«®±°»¿² Ü·®»½¬·ª» îððîñçêñÛÝ ®»¯«·®»- ¬¸¿¬ ¬¸» »¯«·°³»²¬ ¾»¿®·²¹ ¬¸·- -§³¾±´ ±² ¬¸» °®±¼«½¬ ¿²¼ñ±® ·¬- °¿½µ¿¹·²¹ ³«-¬ ²±¬ ¾» ¼·-°±-»¼ ±º ©·¬¸ «²-±®¬»¼ ³«²·½·°¿´ ©¿-¬»ò ̸» -§³¾±´ ·²¼·½¿¬»¬¸¿¬ ¬¸·- °®±¼«½¬ -¸±«´¼ ¾» ¼·-°±-»¼ ±º -»°¿®¿¬»´§ º®±³ ®»¹«´¿® ¸±«-»¸±´¼ ©¿-¬» -¬®»¿³-ò ׬ ·- §±«® ®»-°±²-·¾·´·¬§ ¬± ¼·-°±-» ±º ¬¸·- ¿²¼ ±¬¸»® »´»½¬®·½ ¿²¼ »´»½¬®±²·½ »¯«·°³»²¬ ª·¿ ¼»-·¹²¿¬»¼ ½±´´»½¬·±² º¿½·´·¬·»- ¿°°±·²¬»¼
C Regulatory Information Ü¿²-µ øÜ¿²·-¸÷ ó Ó·´¶(·²º±®³¿¬·±² º±® µ«²¼»® · ÛË ÛËó¼·®»µ¬·ª îððîñçêñÛÚ µ®:ª»®ô ¿¬ «¼-¬§® ¼»® ¾:®»® ¼»¬¬» -§³¾±´ °; °®±¼«µ¬»¬ ±¹ñ»´´»® »³¾¿´´¿¹»² ·µµ» ³; ¾±®¬-µ¿ºº»- -±³ «-±®¬»®»¬ µ±³³«²¿´¬ ¿ºº¿´¼ò ͧ³¾±´»¬ ¾»¬§¼»®ô ¿¬ ¼»¬¬» °®±¼«µ¬ -µ¿´ ¾±®¬-µ¿ºº»- ¿¼-µ·´¬ º®¿ ¼»¬ ¿´³·²¼»´·¹» ¸«-¸±´¼²·²¹-¿ºº¿´¼ò Ü»¬ »® ¼·¬ ¿²-ª¿® ¿¬ ¾±®¬-µ¿ºº» ¼»¬¬» ±¹ ¿²¼»¬ »´»µ¬®·-µ ±¹ »´»µ¬®±²·-µ «¼-¬§® ª·¿ ¾»-¬»³¬» ·²¼-¿³´·²¹--¬»¼»® «¼°»¹»¬ ¿º -¬¿¬»² »´´»® ¼» ´±µ¿´» ³§²¼·¹¸»¼»®ò Õ±®®»µ¬ ¾±®¬-µ¿ºº»´-» ±¹ ¹»²ª
Regulatory Information C Ú®¿²9¿·- øÚ®»²½¸÷ ó ײº±®³¿¬·±²- »²ª·®±²²»³»²¬¿´»- °±«® ´»- ½´·»²¬- ¼» ´•Ë²·±² »«®±°7»²²» Ô¿ ¼·®»½¬·ª» »«®±°7»²²» îððîñçêñÝÛ »¨·¹» ¯«» ´•7¯«·°»³»²¬ -«® ´»¯«»´ »-¬ ¿°°±-7 ½» -§³¾±´» -«® ´» °®±¼«·¬ »¬ñ±« -±² »³¾¿´´¿¹» ²» -±·¬ °¿- ¶»¬7 ¿ª»½ ´»- ¿«¬®»- ±®¼«®»- ³7²¿¹8®»-ò Ý» -§³¾±´» ·²¼·¯«» ¯«» ´» °®±¼«·¬ ¼±·¬ 6¬®» 7´·³·²7 ¼¿²- «² ½·®½«·¬ ¼·-¬·²½¬ ¼» ½»´«· °±«® ´»- ¼7½¸»¬- ¼»³7²¿¹»-ò ×´ »-¬ ¼» ª±¬®» ®»-°±²-¿¾·´·¬7 ¼» ¶»¬»® ½» ³¿¬7®·»´ ¿·²-· ¯«» ¬±«¬ ¿«¬®» ³¿¬7®·»´ 7´»½¬®·¯«» ±« 7´»½¬®±
C Regulatory Information µ¿·¬¶«³- ¼¿¾¿· «² ½·´ªµ« ª»-»´¾¿·ò ͵µ¿- ¦·¿- °¿® ²±ª»½±¶«ƒ¿ ¿°®µ±¶«³¿ ·¦³»ƒ¿²« ¿¬µ®·¬«³±- ¶- ª¿®¿¬ -¿»³¬ ª·»¬¶ °¿ƒª¿´¼¾ô ¿¬µ®·¬«³« -¿ªµƒ¿²¿- ¼·»²»-¬ô µ ¿® ª»·µ¿´ô µ«® ·»¹¼¶¬·»- ƒ± ·¦-¬®¼¶«³«ò Ô·»¬«ªƒµ¿· øÔ·¬¸«¿²·¿²÷ ó ß°´·²µ±-¿«¹±- ·²º±®³¿½·¶¿ô -µ·®¬¿ Û«®±°±- Ͷ«²¹±- ª¿®¬±¬±¶¿³Û«®±°±- ¼·®»µ¬§ª¿ îððîñçêñÛÝ ²«³¿¬±ô µ¿¼ ®¿²¹±-ô µ«®· ·® µ«®·±- °¿µ«±¬ §®¿ °¿‚§³¬¿ ƒ·«± -·³¾±´·« øª»-µ·¬» -·³¾±´÷ô ²»¹¿´·³¿ ƒ¿´·²¬· µ¿®¬« -« ²»®ƒ·«±¬±³·- µ±³«²¿´·²³·- ¿¬´·»µ±³·-ò ‰·- -·³¾±´·- ®±¼±ô µ¿¼ ¹¿³·
C Regulatory Information Ò±®-µ øÒ±®©»¹·¿²÷ ó Ó·´¶(·²º±®³¿-¶±² º±® µ«²¼»® · ÛË ÛËó¼·®»µ¬·ª îððîñçêñÛÚ µ®»ª»® ¿¬ «¬-¬§® ³»¼ º(´¹»²¼» -§³¾±´ ¿ª¾·´¼»¬ °; °®±¼«µ¬»¬ ±¹ñ»´´»® °¿µ²·²¹»²ô ·µµ» ³; µ¿-¬»- -¿³³»² ³»¼ «-±®¬»®¬ ¿ªº¿´´ò ͧ³¾±´»¬ ·²¼·µ»®»® ¿¬ ¼»¬¬» °®±¼«µ¬»¬ -µ¿´ ¸;²¼¬»®»- ¿¬-µ·´¬ º®¿ ±®¼·²:® ¿ªº¿´´-·²²-¿³´·²¹ º±® ¸«-¸±´¼²·²¹-¿ªº¿´´ò Ü»¬ »® ¼·¬¬ ¿²-ª¿® ; µª·¬¬» ¼»¹ ³»¼ ¼»¬¬» °®±¼«µ¬»¬ ±¹ ¿²²»¬ »´»µ¬®·-µ ±¹ »´»µ¬®±²·-µ ¿ªº¿´´ ª·¿ »¹²» ·²²-¿³´·²¹-±®¼²·²¹»® -´·µ ³§²¼·¹¸»¬»²» »´´»® µ±³³«²»²» ¾»-¬»³³»®ò Õ±®®
C Regulatory Information б¼¿ »«®-°-µ»¶ -³»®²·½» îððîñçêñÛÍ ¦¿®·¿¼»²·» - ¬#³¬± -§³¾±´±³ ²¿ °®±¼«µ¬» ¿ñ¿´»¾± ¶»¸± ¾¿´»²3 ²»-³·» ¾§ ´·µª·¼±ª¿²7 -°±´« - ²»¬®·»¼»²#³ µ±³«²?´²§³ ±¼°¿¼±³ò ͧ³¾±´ ¦²¿³»²?ô ‚» °®±¼«µ¬ ¾§ -¿ ³¿´ ´·µª·¼±ª¿ ±¼¼»´»²» ±¼ ¾»‚²7¸± ±¼°¿¼« ¦ ¼±³?½²±-¬3ò Ö» ª¿ƒ±« °±ª·²²±-±« ´·µª·¼±ª¿ ¬±¬± · ±-¬¿¬²7 »´»µ¬®·½µ7 ¿ »´»µ¬®±²·½µ7 ¦¿®·¿¼»²·¿ °®±-¬®»¼²3½¬ª±³ ƒ°»½·¿´·¦±ª¿²#½¸ ¦¾»®²#½¸ ¦¿®·¿¼»²3 «®»²#½¸ ª´?¼±« ¿´»¾± ³·»-¬²§³· ±®¹?²³·ò Í°®?ª²¿ ´·µª·¼?½·¿ ¿ ®»½§µ´?½·¿ °±³,‚» ¦¿¾®?²· °®3°¿¼²#³ ²»¹¿¬3ª²§
D Where to Go From Here This appendix describes additional resources that are available to help you and your customer obtain the full benefits of the SPA9000 Voice System. Cisco WRP400 User Guide Resource Location Technical Documentation www.cisco.com/en/US/products/ps10024/ tsd_products_support_series_home.html Firmware Downloads www.cisco.com/en/US/products/ps10024/index.html Customer Support www.cisco.com/en/US/support/ tsd_cisco_small_business_support_center_contacts.
