Wireless-G USB Network Adapter 7. The Setup Wizard will ask you to review your settings before it starts to install files. Click Next if you are satisfied with your settings, or click Back to change any settings. Figure 4-13: Setup Wizard’s Check Settings Screen 8. At this point, you may see a Digital Signature Not Found screen indicating that a digital signature was not found. The Adapter’s software has been tested and found to work successfully with Windows 2000. Click the Yes button to continue.
Wireless-G USB Network Adapter Chapter 5: Connecting the Wireless-G USB Network Adapter NOTE: You must run the Setup Wizard before connecting the Adapter. Connecting the Adapter 1. Connect one end of the included USB cable to the Adapter’s USB port. 2. Connect the other end of the cable to one of the USB ports on your computer. 3. The Power LED should light up when the Adapter is plugged in. Figure 5-1: How the Adapter Connects to Your PC 4.
Wireless-G USB Network Adapter Using the Adapter’s Wall Mount The Adapter’s Wall Mount allows you to easily attach the Adapter to your wall for better reception and more convenient placement. 1. Attach the separate adhesive strip of velcro to the wall where you will be mounting the Adapter. 2. To attach the Wall Mount to the Adapter, slide the Wall Mount into the grooves on the back panel of Adapter, as shown in Steps A, B, and C. 3.
Wireless-G USB Network Adapter Chapter 6: Using the Wireless Network Monitor Use the Wireless Network Monitor to check the link information, search for available wireless networks, or create profiles that hold different configuration settings. Using the Wireless Network Monitor Icon After installing the Adapter, the Wireless-G USB Network Adapter Wireless Monitor icon will appear in your system tray. If the Wireless Network Monitor is enabled, then the icon will be green.
Wireless-G USB Network Adapter Accessing the Wireless Network Monitor Besides selecting Turn on when you right-click the icon, you can also double-click the Wireless Network Monitor icon to activate the Wireless Network Monitor. Then the Link Information screen will appear. From this screen, you can find out how strong the current wireless signal is and how good the connection’s quality is.
Wireless-G USB Network Adapter Wireless Network Status The Wireless Network Status screen provides information on your current network settings. Status - The status of the wireless network connection. SSID - This is the unique name of the wireless network. Wireless Mode - The mode of the wireless network currently in use is displayed here. Transfer Rate - The data transfer rate of the current connection is shown here. Channel - This is the channel to which the wireless network devices are set.
Wireless-G USB Network Adapter Wireless Network Statistics The Wireless Networks Statistics screen provides statistics on your current network settings. Transmit Rate - This is the data transfer rate of the current connection. (In Auto mode, the Adapter dynamically shifts to the fastest data transfer rate possible at any given time.) Receive Rate - This is the rate at which data is received.
Wireless-G USB Network Adapter Site Survey The Site Survey screen displays a list of infrastructure and ad-hoc networks available for connection in the table on the left. This table shows the network’s SSID, Channel, and the quality of the wireless signal the Adapter is receiving. You may click SSID, CH (Channel), or Signal, to sort by that field. SSID - The SSID or unique name of the wireless network is displayed here. CH - This is the channel setting that the network uses.
Wireless-G USB Network Adapter Profiles The Profiles screen lets you save different configuration profiles for different network setups. The table on the left displays a list of infrastructure and ad-hoc networks available for connection. This table shows the network’s profile name and the wireless network’s SSID, as set in the connection profile. Profile Information For each profile selected, the following are listed: Wireless Mode - This is the mode of the wireless network currently in use.
Wireless-G USB Network Adapter Creating a New Profile 1. On the Profiles screen, click the New button to create a new profile. Figure 6-13: Create a New Profile 2. Enter a name for the new profile, and click the OK button. Click the Cancel button to return to the Profiles screen without entering a name. 3. The Network Settings screen will appear. If your network has a router or other DHCP server, click the radio button next to Obtain network settings automatically (DHCP).
Wireless-G USB Network Adapter 4. The Wireless Mode screen shows a choice of two wireless modes. Click the Infrastructure Mode radio button if you want your wireless computers to communicate with computers on your wired network via a wireless access point. Click the Ad-Hoc Mode radio button if you want multiple wireless computers to communicate directly with each other. Enter the SSID for your network. Click the Next button to continue or the Back button to return to the previous screen.
Wireless-G USB Network Adapter 6. Select the method of security you want to use: WEP, PSK, PSK + RADIUS, or RADIUS. WEP stands for Wired Equivalent Privacy, and PSK stands for Pre-Shared Key. RADIUS stands for Remote Authentication Dial-In User Service. NOTE: If your network is using WPA-Personal or WPA-PSK security, then select PSK. If your network is using WPA-Enterprise or WPA-RADIUS security, then select PSK + RADIUS.
