Installation Manual

ManualsBrandsLippert Components ManualsOtherLippert Components 429756 Black Jack-It 2-Bike Trailer A-Frame Mounted Rack

lippertcomponents.com 574-537-8900 Rev: 02.17 - Jack-It

Jack-It

Installation and Owner’s Manual

(For Aftermarket Application)

Table of Contents

Introduction ............................................ 1

Safety Requirements ................................... 1

Resources Required ................................... 2

Installation Instructions ............................... 2

Manual Jack Operation ................................ 3

Securing Bikes ......................................... 4

Dimensions Of Assembled Jack-It ..................... 4

Maximum Weight Capacity ............................ 4

Jack-It

Installation and

Owner’s Manual

(For Aftermarket Applications)

Introduction

The Jack-It

is a bicycle rack designed to attach to

your RV.

Additional information about this product can be obtained

from www.lci1.com/support or by downloading the free

myLCI app. The app is available on iTunes

for iPhone

and iPad

and also on Google Play

™

for Android

™

users.

iTunes, iPhone, and iPad are registered trademarks of

Apple Inc. Google Play and Android are trademarks of

Google Inc.

Lippert Components, Inc. recommends that the following

inspections, troubleshooting, component replacement and

verications be completed only by certied RV technicians.

Safety Requirements

Patent protected, trademarked, and produced by Let’s Go Aero, Inc.

Corporate Ofce: 4474 Barnes Road, Colorado Springs, CO 80917 USA.

Made in Taiwan.

US Patent Numbers: 8,899,456, D717,716, D717,717, D684,917, D722,289,

patents pending.

MOVING PARTS CAN PINCH, CRUSH OR CUT. KEEP

CLEAR AND USE CAUTION.

FAILURE TO FOLLOW THE INSTRUCTIONS PROVIDED

IN THIS MANUAL MAY RESULT IN DEATH, SERIOUS

INJURY, VEHICLE DAMAGE OR VOIDING OF THE

COMPONENT WARRANTY.

THE USE OF THIS PRODUCT WHILE BICYCLES ARE

LOADED MAY AFFECT THE TURNING RADIUS ON

SOME VEHICLES. CHECK THE TURNING RADIUS

BEFORE TRAVEL.

Summary of content (8 pages)

PAGE 1
Jack-It ® Installation and Owner’s Manual (For Aftermarket Application) Jack-It ® Installation and Owner’s Manual (For Aftermarket Applications) Introduction The Jack-It ® is a bicycle rack designed to attach to your RV. Additional information about this product can be obtained from www.lci1.com/support or by downloading the free myLCI app. The app is available on iTunes® for iPhone® and iPad® and also on Google Play™ for Android™ users.
PAGE 2
Jack-It ® Installation and Owner’s Manual (For Aftermarket Application) Resources Required • 9/16” Socket Wrench E • 3/4” Socket Wrench B D Installation Instructions 1. Remove the tongue jack from the coupler. Position the PowerTower™ (Fig.1G) on the coupler. Place the tongue jack on the PowerTower (Fig.1G) and secure both to the coupler using 3 nuts, bolts and washers each (Fig.1H, 1I and 1J). C A NOTE: If there is no tongue jack, attach the PowerTower (Fig.
PAGE 3
Jack-It ® Installation and Owner’s Manual (For Aftermarket Application) NOTE: Several hole positions are provided for cradles (Fig.2A). Pads (Fig.2D) and SwayStop™ pins (Fig.2F) slide along the length of the wings (Fig.2G). B 4. Slide one SwayStop pin (Fig.2F) onto each wing (Fig.2G) from the bottom so that the SwayStop locates between the snap pin (Fig.2H) and the pad (Fig.2D). NOTE: A 2 and optional SwayStop pin (Fig.3) is provided to secure both wheels of the bike to the rack.
PAGE 4
Jack-It ® Installation and Owner’s Manual (For Aftermarket Application) Securing Bikes 46 3/4” 1. For 2 bicycles, the best technique is to position the bicycles front to back/back to front with the chain ring to the outside. 2. Hang 1 bicycle on the trailer side of the bicycle rack so the top of the wheels are each supported by a cradle (Fig.7). 3. Secure by tensioning each rubber strap over the top of each tire and engaging a strap hole with the end of the cradle. 4.
PAGE 5
Jack-It ® Installation and Owner’s Manual (For Aftermarket Application) Jack-It ® Manuel de l’utilisateur Introduction Le Jack-IT® est un porte-vélos conçu pour être fixé à votre VR. Vous pouvez obtenir des renseignements supplémentaires concernant ce produit sur le site www.lci1.com/support ou en téléchargeant l’application gratuite myLCI. L’application est offerte sur iTunes® pour iPhone® et iPad® et aussi sur Google PlayMC pour les utilisateurs d’AndroidMC.
PAGE 6
Jack-It ® Manuel de l’utilisateur Outils requis • Clé à douilles de 9/16 po (14 mm) E • Clé à douilles de 3/4 po (19 mm) B Instructions d’installation D 1. Retirer le vérin de flèche du coupleur. Positionner le PowerTowerMC (Fig.1G) sur le coupleur. Placer le vérin de flèche sur le PowerTower (Fig.1G) et fixer les deux au coupleur à l’aide de trois écrous, boulons et rondelles chacun (Fig.1H, 1I et 1J). C A REMARQUE: S’il n’y a pas de vérin de flèche, fixer le PowerTower (Fig.
PAGE 7
Jack-It ® Manuel de l’utilisateur REMARQUE: Plusieurs positions de trous sont fournies pour les brides de fixation (Fig.2A). Les tampons (Fig.2D) et les tiges SwayStopMC (Fig.2F) glissent le long des ailes (Fig.2G). B 4. Glisser une tige SwayStop (Fig.2F) sur chaque aile (Fig.2G) à partir du bas de sorte que la tige SwayStop se positionne entre la goupille à pression (Fig.2H) et le tampon (Fig.2D). C REMARQUE: Une deuxième tige optionnelle SwayStop (Fig.
PAGE 8
Jack-It ® Manuel de l’utilisateur Installation des vélos 1188 mm 1. Pour deux vélos, la meilleure technique consiste à positionner les vélos avant vers arrière/arrière vers avant avec le plateau de chaîne orienté vers l’extérieur. 2. Installer un vélo sur le porte-vélos du côté de la caravane de sorte que le dessus de chaque roue soit supporté par une bride de fixation (Fig.4). 3.