User Manual

22
SETUP - CALIBRATION SETUP
Preparing for Calibration
Before the LCR 600 is put into daily operation, the register must be dened and proved according to the liquid that
the owmeter will be measuring. This is done in the Calibration Setup screens. Although the LCR 600 can hold a
total of 16 different calibrations simultaneously, FlightConnect is designed for only one calibration (Calibration #1). In
FlightConnect, the primary purpose of the Calibration Setup screens is to calibrate Product 1 of the LCR 600.
To calibrate an LCR 600
1. Remove the switchplate and move the selector switch to the calibration position.
2. Enter the proper settings in Calibration Setup 1 and Calibration Setup 2.
3. Prove the owmeter system with single-point or multi-point calibration.
CALIBRATION SETUP 1
Calibration #: (LB) C - U - L
FlightConnect
The active calibration of 16 possible calibrations. The elds shown
on the Calibration Setup 1 screen represent the values of the
Calibration # shown. Any edits made to the elds are attributed
to the Calibration # shown. FlightConnect only uses Calibration
#1.
Calibration Code: (TB) C - U
FlightConnect
The code assigned to the active calibration. This code can be used
to correspond with an ofce code. A value in this eld is not required
for FlightConnect.
Calibration Name: (TB) C - U
FlightConnect
The text designation of the active calibration. A value in this eld is not required for FlightConnect.
Calibration Type: (LB) C
FlightConnect
The product type of the active calibration. Aviation is the preferred FlightConnect setting.
Ammonia • Aviation • Distillate • Gasoline • Methanol • LPG • Lube Oil • blank
Linearization Mode: (LB) C
Disables and enables single and multi-point calibration.
Setup 
Applied 
Pulses/Unit <k-Factor>: (TB) C
The number of pulse edges per unit of measure. Applies only to gross volume. This number scales the prover
quantity. A unit of 20.0000 is entered on all factory shipments. Changing the k-factor moves the entire owmeter
accuracy curve either up or down. See table on page 26.
Prover Quantity: (TB) C
The metered volume of the prover after a calibration fueling. When the prover volume is entered, the LCR 600 adjusts
the k-factor to calibrate the pulses/unit. See calibration instructions.
BEGIN CALIBRATION DELIVERY
Starts a calibration fueling. See page 25.
S1 Close: (TB) C
FlightConnect
The point during a preset fueling when the valve switches from full ow to a dwell ow. The LCR 600 will switch the
valve to dwell ow when the volume remaining in the preset fueling reaches the value of this eld. 0 to 500 range. 0
is the preferred FlightConnect setting (aviation owmeter systems typically do not have two-stage valves, which are
required for this feature).
Net Totalizer: Display only C
Total accumulated net (temperature compensated) volume delivered by the LCR 600. In the calibration position, this
eld can be set to any positive value. The value resets after a clear all.
Gross Totalizer: Display only C
Total accumulated gross volume delivered by the LCR 600. In the calibration position, this eld can be set to any
positive value. The value resets after a clear all.
Calibration #: 1
Calibration Code:
Calibration Name:
Calibration Type:
Linearization Mode:
Pulses/Unit:
Prover Quantity:
BEGIN CALIBRATION DELIVERY
S1 Close
Net Totalizer
Gross Totalizer
Gallons
Aviation
Setup
20.0000
00 Gallons
2.0 Gallons
0.0 Gallons
141.7 Gallons
CALIBRATION SETUP
Next/Previous Screen
1
TB - Text Box
LB - List Box
Field Type