Installation & Parts Manual Gear Plate Selection Guide Installation: M100-30 www.lcmeter.
Table of Contents Description Page Number Gear Plate Selection Guide .................................................... 3 General Meter Data ..................................................... 3 Packing Gland Ratio ............................................................... 4 Pattern Codes .............................................................. 4 Gears ..................................................................................... 5 Gear Limitations .....................................
Gear Plate Selection Guide Gear plates are used to convert a meter’s output to the desired unit of measure; for example, 1/10 or whole US gallons, 1/10 or whole imperial gallons, liters, cubic meters, barrels, pounds, etc. To facilitate the changing of the unit of measure desired, the gear plate is attached to the base of the large numeral counter with two screws. To make proper gear plate selection, you will need to know: 1. Meter size 2. Unit of measure required 3. Packing gland ratio 4.
Packing Gland Ratio Three packing gland ratios are available to permit achieving the proper RPM of the register unit wheel (right hand wheel). Pattern Codes The Pattern Code number diagram shows five general gear assembly configurations that can be constructed using the basic gear plate and swing arm assemblies. Patterns 10, 30, and 50 can be used with a mechanical temperature compensator.
Gears Gear Limitations Available Gears • • Standard gears range from 30 to 69 teeth inclusive. Other gears available are listed below. • Adjuster Reduction: 3.997:1 at 25% setting. Two Gear Ratio Capacity: Pattern 10 must equal 118 total teeth. Idler Arm Capacity: Patterns 20, 30, 40, & 50: 114 teeth maximum, 72 teeth minimum. C-D A-B E-F B A X D C X F E No.
Formulas for Computing Gear Plate Ratios Nb x Rc = R1 Pg x W x Ra R2= 7. R2 = Dn divided by Dr, which is the actual ratio. Dn Dr 8. Dn = Driven gear. 1. Nb = Revolutions per gallon of the blocking rotor. 9. Dr = Driving gear Meter Model Nb Value M-5 (old style) ------------- 4.0790 M-5 (new style) ---------- 12.2370 MS-5 ----------------------- 12.2370 M-7 --------------------------- 5.555 MS-7 ------------------------- 5.555 M-10 ------------------------- 5.555 M-15 ------------------------- 2.
Formulas for Computing Gear Plate Ratios Examples Example 1: Find a gear plate ratio for 7.50 pounds per gallon. Example 2: Find a gear plate ratio for Imperial Gallons at 2% correction. Meter Model: ------------Unit of Measure: -------Packing Gland Ratio: -Units per Gallons: -----Adjuster Ratio: ---------- Meter Model: ------------Unit of Measure: -------Correction Factor ------Packing Gland Ratio: -Units per Gallons: ------ M7-A pounds per gallon 2:1 7.50 3.997 Nb x Rc = R1 Pg x W x R a 5.
Gear Plate Assemblies Pattern 10, Long Shaft (LC Preset) 8
Gear Plate Assemblies Pattern 10, Short Shaft 9
Gear Plate Assemblies Patterns 20, 30, 40, & 50 Long Shaft (LC Preset) 10
Gear Plate Assemblies Patterns 20, 30, 40, & 50 Short Shaft 11
Parts List Gear Plate Assemblies: Basic Gear Plate Part Numbers for Pattern Styles: Patterns 10, 20, 30, 40, & 50 Item No.
Swing Arm Assemblies Pattern 20 & 40 (1 Swing Arm) Bevel Gear 13
Swing Arm Assemblies Pattern 30 & 50 (2 Swing Arms) Bevel Gear 14
Gear Plates by Meter Size & Unit of Measure Meter Model Unit of Measure Gear Plate Number M5 US Gallon 1/10 US Gallon Imp. Gallon 1/10 Imp. Gallon Liters/Gallons G1103 G1125-59 tooth expanded G1150 G1165 G1620 2:1 3:1 2:1 3:1 2:1 1/10 US Gallon G1127 1:1 M7 MS7 US Gallon 1/10 US Gallon Liters/Gallons Imp. Gallon 1/10 Imp. Gallon G2112 G2132-69 tooth expanded G2681 G2156 G2166 2:1 2:1 2:1 2:1 2:1 MA7 1/10 US Gallon G2146 1:1 M15 MS15 MA15 M25 US Gallon 1/10 US Gallon Liters/Gallons Imp.
M-5 Gear Plate Listing Units of Measure Units per Rev G1101 G1102 G1103 G1104 G1106 G1107 G1113 G1114 G1115 G1116 US Gal US Gal US Gal US Gal US Gal US Gal US Gal US Gal US Gal US Gal 10 10 10 10 10 10 10 10 10 10 Preset/TVC TVC Preset TVC Preset/TVC TVC Preset/TVC 5.0988 5.0988 5.0988 5.0988 4.9805 4.9805 15.3198 15.3198 15.0000 15.
M-5 Gear Plate Listing (continued) Part # G1638 G1643 G1644 G1645 G1646 G1647 G1648 G1649 Units of Measure Units per Rev LITRES/Gal LITRES/Gal LITRES/Gal LITRES/Gal LITRES/Gal LITRES/Gal LITRES/Gal LITRES/Gal 10 10 10 10 10 10 10 10 Range High Used With Low Special Notes P/G Ratio 2% Direct Drive ONLY Direct Drive ONLY Direct Drive ONLY Direct Drive ONLY 2% - Direct Drive ONLY 2% - Direct Drive ONLY 2% - Direct Drive ONLY 3:1* 2:1 2:1 2:1 2:1 2:1 2:1 2:1 Ratio Preset/TVC Preset TVC Preset/TVC
M-7 & M-10 Gear Plate Listing (continued) Part # G2304 G2309 G2313 G2314 G2317 G2320 G2321 G2322 G2324 G2327 G2328 G2329 G2330 G2331 G2334 G2337 G2340 G2341 G2344 G2346 G2347 G2349 G2350 G2357 G2358 G2365 G2368 G2371 G2374 G2377 G2378 G2387 G2393 G2394 G2398 G2401 G2405 G2411 G2414 G2418 G2428 G2429 G2433 G2435 G2438 G2442 G2445 G2446 G2451 G2455 G2458 G2461 G2467 G2468 G2471 G2477 G2480 G2483 G2486 G2489 G2492 G2495 G2496 G2501 G2502 G2507 G2510 G2513 Units of Measure Units per Rev High low LBS/GAL
M-7 & M-10 Gear Plate Listing (continued) Units of Measure Units per Rev High low G2514 G2520 G2523 G2524 G2530 G2533 G2534 G2536 G2537 G2543 G2544 G2547 G2548 G2551 G2554 G2555 G2561 G2564 G2565 G2567 G2568 G2571 G2572 G2575 G2578 G2581 G2584 G2587 G2589 G2590 G2596 G2599 LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL L
M-15 & M-25 Gear Plate Listing Units of Measure Units per Rev G3114 G3115 G3116 G3123 G3124 G3125 G3126 US GAL US GAL US GAL US GAL US GAL US GAL US GAL 10 10 10 10 10 10 10 PRESET G3160 G3161 1/10 US GAL 1/10 US GAL 1 1 PRESET G3200 G3201 G3202 G3203 IMP GAL IMP GAL IMP GAL IMP GAL 10 10 10 10 G3215 G3216 G3217 G3218 1/10 IMP GAL 1/10 IMP/GAL 1/10 IMP GAL 1/10 IMP GAL 1 1 1 1 G3229 G3230 G3235 KG/GAL KG/GAL KG/GAL 10 10 100 3.436 3.44 3.368 3.
M-30 & M-40 Gear Plate Listing Units of Measure Units per Rev G4110 G4111 G4115 G4116 G4118 G4120 G4121 G4132 G4134 US GAL US GAL US GAL US GAL US GAL US GAL US GAL US GAL US GAL 10 10 10 10 10 10 10 100 100 G4150 G4151 G4153 G4154 IMP GAL IMP GAL IMP GAL IMP GAL 10 10 10 10 G4219 G4221 G4223 G4225 G4227 G4229 G4231 G4233 G4236 G4239 G4242 G4245 G4248 G4252 G4255 G4258 G4261 G4264 G4267 G4270 G4273 G4276 G4279 G4282 G4285 G4288 G4291 G4294 G4297 G4300 G4303 G4306 G4309 G4312 G4315 G4318 G4321 G4324
M-30 & M-40 Gear Plate Listing (continued) Units of Measure Units per Rev High low G4348 G4351 G4354 G4357 G4358 G4360 G4363 G4366 G4367 G4370 G4372 G4374 G4376 G4378 G4380 G4382 G4384 G4386 G4388 G4390 G4392 G4393 G4394 G4395 G4397 G4398 G4400 G4401 G4402 G4403 G4404 G4405 G4406 LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LBS/GAL LB
M-60, MS-75, M-80 & MS-120 Gear Plate Listing M-60 (old style) & MS-75 Units of Measure Units per Rev G5110 G5115 G5117 G5140 US GAL US GAL US GAL US GAL 10 10 10 10 G5210 G5211 G5212 IMP GAL IMP GAL IMP GAL 10 10 10 PRESET G5410 G5411 G5412 DEKALITERS/GAL DEKALITERS/GAL DEKALITERS/GAL 10 10 10 PRESET G5453 G5454 CUBIC METERS CUBIC METERS G5510 42 GAL/BARREL Part # Range High low Used With Special Notes Ratio P/G Ratio Ratio Recip Check Pat # Gear & POS # A-B-C-D-E-F Min Max 1:
A Unit of IDEX Corporation 105 Albrecht Drive Lake Bluff, IL 60044-2242 1.800.458.52628 • 47.295.1050 Fax: 847.295.1057 www.lcmeter.com © 2004 Liquid Controls Pub. No.