Instructions / Assembly

A division of
Une division de
Una división de
Copyright © 2020, Liteline Corporation. All rights reserved.
LITELINE CORPORATION
P 416-996-1856 | 1-866-730-7704
F 905-709-5255 | 1-888-738-9736
EN
IMPORTANT: Read all instructions before installing  xtures. Retain
for future reference.
SAFETY: For your safety, this  xture must be wired in accordance to
local electrical codes and ordinances. All work should be done by a
quali ed electrician.
WARNING:
• Make certain power is OFF from the electrical panel before
starting installation or attempting any maintenance. Indoor
installation only.
• Do not mix di erent sizes on the same dimmer, not all  xtures
will exhibit the same dimming level.
TOOLS REQUIRED:
• Drywall Saw
• Measuring Tape
• Electrical Wiring (use type and gauge suitable for application to
connect the  xtures)
ASSEMBLY INSTRUCTIONS:
1. Turn power OFF from the electrical panel before starting
installation.
2. Locate a suitable position to place the  xture and open a hole in
accordance to the cut-hole dimensions (refer to Hole Cut Table for
appropriate size).
3. Run the electrical wire from the switch (power supply) through
the mounting hole – use NMD90 Romex or BX cable.
4. Open the hardwire box swing cover and remove the appropriate
knockout(s).
5. Insert the electrical supply cable through the knockout and
secure with a cable connector (sold separately).
6. Wire box using supplied quick connect push-in terminals.
Connect green ground wire of cable to green wire on box.
Connect white wire of cable to white wire of box. Connect black
wire of cable to black wire of box [Fig. 1].
7. Place all wiring and connections back in to the box and close
the cover.
8. New construction applications: Hardwire box shall be  rmly
secured to studs, joists, or similar  xed structural units [Fig. 2].
Remodel applications: Do not require the hardwire box to
be  rmly secured after the mounting plates, studs, joists, or
structural units that have been concealed. Snap o the hardwire
box tabs [Fig. 3], then insert into ceiling [Fig. 4].
9. Select desires color temperature using the selector button at the
back of the  xture (preset to 2700 K) [Fig. 5].
10. Push spring loaded clips on the  xture upwards and insert
 xture base in to the mounting hole. Release the clips and
 xture will be pulled  ush to the ceiling [Fig. 6].
11. Once assembly is complete, turn on power to con rm  xture is
working properly.
Fig. 4
Fig. 6
Fig. 5Fig. 3
Fig. 2
REV 9.15.20
SL4-12RG Series
RECESSED LIGHTING • LUMINAIRE ENCASTRE • LÁMPARAS EMPOTRADAS
COLOR SELECTABLE 4" GIMBAL
GIMBAL COULEUR SÉLECTIONNABLE, 4 PO
GIMBAL 4" CON TEMPERATURA DE COLOR SELECCIONABLE
Power supply
Bloc d'alimentation
Fuente de alimentación
Black wire
Fil noir
Cable negro
White wire
Fil blanc
Cable blanco
Quick connect push-in terminals
Bornes à bouton
Terminales de conexión rápida
Quick connect push-in terminals
Bornes à bouton
Terminales de conexión rápida
Cable to fi xture
Câble sur le montage
Cable a lámpara
Green wire
Fil vert
Cable verde
Fig. 1
For more information on our lifetime warranty, please visit www. trenzlighting.com/goldlabel
Pour plus d'informations sur notre garantie à vie, s'il vous plaît visitez www. trenzlighiting.com/goldlabel
Para obtener más información sobre nuestra garantía de por vida, visite www. trenzlighiting.com/goldlabel
Hole Cut Size / Taille Trou Découpé / Tamaño de
corte del Orifi cio
SL4-12RG-90 Ø 4¼ " (108mm)