LITEMAX DPD1334-STQ-Q01 13.3” LED B/L LCD User Manual Approved by Checked by Prepared by LITEMAX Electronics Inc. 8F, No.137, Lane 235, Bau-chiau Rd., Shin-dian Dist., New Taipei City, Taiwan R.O.C. Tel : 886-2-8919-1858 Fax: 886-2-8919-1300 Homepage: http://www.litemax.com LITEMAX Electronics Inc.
Record of Revision Version and Date Page July/1/2020 all LITEMAX Electronics Inc.
Contents Record of Revision ...................................................................................................................................... 2 Contents ....................................................................................................................................................... 3 General Description............................................................................................................................ 4 1.1 Features .........................
General Description The DPD1334-STQ-Q01 is a 13.3inch industrial grade LCD with touch and wireless charger function for button deck. The Durapixel LED backlight technology ensures high reliability and low power consumption, suitable for gaming application. 1.1 1.
1.3 Absolute Maximum Ratings [Note 1] Humidity: 95％RH MAX. (Ta≦40℃) Note static electricity. Maximum Wet-bulb temperature at 39℃ or less (Ta>40℃) No condensation [Note 2] The VCC power supply capacity must use the one of 2.5A or more. The VDD power supply capacity must use the one of 5A or more. There is a possibility of causing smoking and the ignition without fusion of LCD fuse when abnormality occurs when the current capacity is smaller than regulated values.
Electrical Characteristics 2.1 TFT-LCD panel driving Ta=+25℃ LITEMAX Electronics Inc.
LITEMAX Electronics Inc.
2.2 Interface Connection LCD Connector : FI-X30SSLA-HF(JAE) Corresponding Connector: FI-X30HL(connector)(JAE) FI-XC3A-1-15000(connector)(JAE) LITEMAX Electronics Inc.
2.3 LVDS interface block diagram LITEMAX Electronics Inc.
2.4 LVDS Data Mapping LITEMAX Electronics Inc.
*: A or B DE: Data Enable [HS]: Hsync [VS]: Vsync [NA]: Non available Hsync/Vsync need not be input so that this model may drive only by rhe ENAB signal. If Hsync/Vsync is input, it doesn’t become a malfunction. LITEMAX Electronics Inc.
2.5 LED backlight LED backlight Connector(CN2): SM10B-SHLS-TF(J.S.T Mfg. Co. Ltd) Corresponding Connector: SHLP-10V-S-B(J.S.T Mfg. Co. Ltd) LITEMAX Electronics Inc.
2.6 Timing Characteristics of Input Signals [Note1] In case of using the long vertical period, the deterioration of display quality, flicker etc. may occur. LITEMAX Electronics Inc.
2.7 Input Data Signals and Display Position on the screen LITEMAX Electronics Inc.
2.8 Input Signals, Basic Display Colors and Gray Scale of Each Color Each basic color can be displayed in gray scales from bit data signals. According to the combination of total 24 bit data signals, the 16.77-million-color display can be achieved on the screen. LITEMAX Electronics Inc.
Optical Specification Item Symbol Red Green Color chromaticity Blue White Min. Typ. Max. Unit Rx 0.577 0.607 0.637 - Ry 0.285 0.315 0.345 - 0.276 0.306 0.336 - 0.558 0.588 0.618 - 0.123 0.153 0.183 - 0.061 0.091 0.121 - Wx 0.251 0.281 0.311 - Wy 0.269 0.299 0.
(2) Definition of Test Point: A B C 1 2 3 Active Area (3) BM-7 Measurement Setup: (4) Klein K-10 Measurement Setup: LITEMAX Electronics Inc.
Backlight driving Section [Note1] On-off conditions for supply voltage [Notw2] Current dissipation VDD= +12.0V, PWM Duty=100% [Note3] BL_EN terminal is connected to a 68K ohm pull-down resistor. [Note4] PWM terminal is not connected pull-down resistor. [Note5] High: Backlight ON Low: Backlight OFF [Note6] fPWM = 1/t15 Duty 10%: MIN. Luminance Duty 100%: MAX. Luminance Luminance changes in proportion to the duty ratio. (t14≧500 us) When the frequency slows, the display fineness might decrease.
[Note7] Luminance becomes 50% of an initial value. (Ta=50℃, PWM=100%) [Note8] The LED used in this LCD module is very sensitive to temperature change. If it operates for extremely long time under high temperature. It is possible rapidly to shorten the life time of LED. In case of such condition, consult with us. [Note9] When PWM signal is set “Low” more than 10ms, please turn off BL_EN. If PWM signal is input without reset of BL_EN.
Mechanical Drawing Unit:mm LITEMAX Electronics Inc.
LITEMAX Electronics Inc.
AD8891DHP Board & OSD Functions We developed this A/D board to support industrial high brightness and commercial applications. This A/D board has many functions. It has a display port and DVI-I and HDMI input. Rev.1 is European RoHS compliant. General Description Max Resolution Up To Full HD Analog RGB Input up to 205MHz ULTRA-RELIABLE DVI-I INPUT HDMI INPUT(HDMI 1.3) Dual/single LVDS interface Support Panel DC 5V or 12V,3.3V Output OSD Control PWM/DC Dimming Control for backlight driver.
Outline Dimensions AD8891 150mmX100mm LITEMAX Electronics Inc.
LITEMAX Electronics Inc.
AD8891 Board Pin Define CN13: Panel LVDS connector Pin No. Function Pin No. Function 1 RxO0- 18 RxE1+ 2 RxO0+ 19 RxE2- 3 RxO1- 20 RxE2+ 4 RxO1+ 21 RxEC- 5 RxO2- 22 RxEC+ 6 RxO2+ 23 RxE3- 7 RxOC- 24 RxE3+ 8 RxOC+ 25 RxE4- 9 RxO3- 26 RxE4+ 10 RxO3+ 27 GND 11 RxO4- 28 GND 12 RxO4+ 29 Pull Low 13 GND 30 Pull Height 14 GND 31 VLCD 15 RxE0- 32 VLCD 16 RxE0+ 33 VLCD 17 RXE1- 34 VLCD CN10: DVI-I INPUT Connector Pin No. Function Pin No.
CN7: DISPLAY PORT Pin No. Function Pin No. Function 1 RX3- 11 GND 2 GND 12 RX0+ 3 RX3+ 13 GND 4 RX2- 14 GND 5 GND 15 AUX+ 6 RX2+ 16 GND 7 RX1- 17 AUX- 8 GND 18 Hot plug detect 9 RX1+ 19 GND 10 RX0- 20 DP +3.3V CN9: HDMI Input connector (HDMI 19Pin) Pin No. Function Pin No. Function Pin No. Function 1 T.M.D.S. Data2+ 9 T.M.D.S. Data0- 17 GND 2 Shield 10 T.M.D.S. Clock+ 18 HDMI 5V Shield 19 Hot Plug Detect 3 T.M.D.S. Data2- 11 4 T.M.D.S.
CN2: Power connector (12V) (6PIN 2.0mm) Pin No. Function Pin No. Function 1 12V/24VDC 2 12V/24VD 3 12V/24VD 4 GND 5 GND 6 GND CN16: Touch Power connector Pin No. Function Pin No. Function 1 5V 2 GND 3 12V 4 GND CN21: Inverter Connector(9PIN 2.0mm) Pin No. Symbol Description Pin No.
CN14: RS232 Connector (3PIN 2.0mm) Pin No. Function Pin No. Function 1 UART TX 2 UART RX 3 GND CN20: LINE IN (3PIN 2.0mm) Pin No. Function Pin No. Function 1 AUDIO-R 2 AUDIO-L 3 GND CN17: Speaker Connector (2PIN 2.0mm) Pin No. Function Pin No. 1 SPK_R+ 2 Function SPK_R- CN18: Speaker Connector (2PIN 2.0mm) Pin No. Function Pin No. 1 SPK_L+ 2 Function SPK_L- CN19: Interrupt Control (4PIN 2.0mm) Pin No. Function Pin No.
CN4: I2C Connector (3PIN 2.0mm) Pin No. Function Pin No. Function 1 I2C_SDA 2 I2C_SCL 3 GND For digital LS JP2: EDID Jumper (2PIN 2.0mm) Pin No. Function 1 3.3V When EDIE wan to update it must be short. Pin No. 2 Function GND CN5: Debug Connector (4PIN 2.0mm) Pin No. Function Pin No. Function 1 3.3V 2 DDCA_SCL 3 DDCA_SDA 4 GND For F/W debug LITEMAX Electronics Inc.
6.1 OSD Function MEMBRANE CONTROL BUTTOM POWER SWITCH: Pushing the power switch will turn the monitor on. Pushing it again to turn the monitor off. Power LED: Power ON-Green / Power off-No. Up Key >: Increase item number or value of the selected item. Menu Key: Enter to the OSD adjustment menu. It also used for go back to previous menu for sub-menu, and the change data don’t save to memory. Down Key <: Decrease item number or item value when OSD is on. Screen Adjustment Operation Procedure 1.
6.2 OSD Menu Here are some instructions for you to use the OSD (On Screen Display). By pressing the “menu”, you will see the below picture. Timing shows resolution and V-frequency of the panel. This 2 information is not changeable by user. There are 7 sub menus within the OSD user interface: Brightness, Signal Select, Sound, Color, Image, Tools, and Exit. When you press the “menu” button, you enter the “Brightness” sub directory.
HDMI: HDMI input Digital: DVI input DP: DisplayPort input (Optional) Exit: back to the beginning menu. Audio Volume: Audio volume adjustment. UnMute/Mute: You can mute the speaker by pressing this option. Exit: back to the beginning menu. LITEMAX Electronics Inc.
Auto Color：By navigating over to the “Auto Color” option, optimal color performance is invoked. SRGB: Windows standard color setting Color Temperature: You have 4 options in this selection . Color Temperature User Define: Default is 100 for “R”, “G”, and “B”. Color Tempture_6500K: Warm color scheme Color Tempture_93OOK: Cold color scheme Exit: back to the beginning menu. LITEMAX Electronics Inc.
Auto Adjust: Choose this option and the AD6038 will adjust to the optimal horizontal and vertical frequency. Clock: If you are not satisfied with the Auto tune result, you can adjust manually by pressing “Clock”. Using this will make the image wider. Phase: If “double images” appear around the characters, choose “Phase” to remove them.. HPos: You can shift the screen horizontally using this function. Vpos: You can shift the screen vertically using this function. Exit: back to the beginning menu.
OSD Control: Selecting this option, brings you to 4 more options: Osd_time: Select time for the OSD user interface to stay on screen, for 2 sec. to 16 sec. Default is 10 sec. Osd_HPos: Moves the OSD user interface horizontally on screen. Osd_VPos: Moves the OSD user interface vertically on screen. Exit: You can exit this sub menu back to the beginning Factory_Reset: By pressing this, the screen will revert to factory settings, and the previous settings will be deleted. LITEMAX Electronics Inc.
Sharpness: Sharpen characters. Exit: back to the normal screen OSD Lock Function： It is possible to lock all the OSD buttons to prevent unauthorized changes to occur by pressing “right >” and “Menu” buttons simultaneously. You will see the “lock” icon below on the center of the screen for 8 ~ 9 seconds. If any button is pushed after the lock function is initiated, the below icon will appear on the screen.' To release the OSD lock, press and “right >” and “Menu”.
Wireless Charger Module Characteristics 7.1 Input Characteristics 7.1.1 Input Voltage & Frequency Item Minimum Normal Maximum Input Voltage 11Vdc 12Vdc 13Vdc Frequency 7.1.2 110KHZ ~ 145KHZ Input Current 1.8mA max. @ 12Vdc 7.1.3 Inrush Current (cold) 2.0mA max. @12Vdc 7.1.4 Full load Full load & Ambient temperature 25℃ Energy Consumption At 11.5Vdc or 12.5Vdc, Energy Consumption≦0,03A 7.2 7.2.
7.3 Mechanical Drawing LITEMAX Electronics Inc.
Precautions 8.1 Handling and Mounting Precautions (1) The module should be assembled into the system firmly by using every mounting hole. Do not apply rough force such as bending or twisting to the LCD during assembly. (2) You should consider the mounting structure so that uneven force (ex. Twisted stress, Concentrated stress) is not applied to the module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the LCD module.
8.3 Operation Precautions (1) Do not pull the I/F connector in or out while the LCD module is operating. (2) Always follow the correct power on/off sequence when LCD module is connecting and operating. This can prevent the CMOS LSI chips from damage during latch-up. (3) Response time depends on the temperature. (In lower temperature, it becomes longer.) (4) Brightness depends on the temperature. (In lower temperature, it becomes lower.) (5) Be careful for condensation at sudden temperature change.
