READ THESE INSTRUCTIONS AND AND SAVE THEM FOR FUTURE USE Model # BR56TBC3M Installation Guide For Models: BR56TBC3M BR56WW3M Model # BR56WW3M Table of Contents: Safety Tips. pg. 2 Unpacking Your Fan. pg. 3 Parts Inventory. pg. 3 Installation Preparation. pg. 4 Hanging Bracket Installation. pg. 4 Fan Assembly. pg. 5 Wiring. pg. 6 Canopy Assembly. pg. 7 Blade Assembly. pg. 7 Wall Control Operation. pg. 7 Testing Your Fan. pg. 8 Troubleshooting. pg. 8 Parts Replacement. pg. 8 Warranty. pg.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a a. j-hook hanging bracket. 1 piece b. blade. 3 pieces b (Model # BR56TBC3M blade) c. motor housing, downrod and canopy (pre-assembled). 1 piece d.
3. Installation Preparation. blade edge 30 10 inches feet (76cm) (3.05m) 12ft. - 20ft. (3.66m - 6.1m) downrod installation This fan can be mounted with a downrod on a regular (no slope) ceiling only. Fan cannot be mounted as a flushmount nor on a vaulted ceiling. 12ft. - 20ft. (3.66 m - 6.1m) To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 10ft. (3.05m) from the floor and 30in. (76cm) from any wall or obstruction.
. Fan Assembly. Loosen canopy set screw and lower canopy to expose hanging bar. Separate electrical wiring and safety cable from rubber band. Lift fan onto j-hook hanging bracket and slide rubber bushing over hook. Make the wiring connections as shown in Section 6 on the following page. j-hook hanging bracket IMPORTANT: Find a secure attachment point (wood ceiling joist highly recommended) and secure safety cable--refer to diagram on the following page as well.
wall control wire 6. Wiring. CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. safety cable black white Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code. If you are unfamiliar with electrical wiring or if the wires in the house/building are different colors than those mentioned below, please consult with a qualified electrician. Connect BLACK wire from fan to BLACK wire from ceiling.
8. Canopy Assembly. Lift canopy until it covers hanging bracket and touches ceiling. Tighten canopy set screw to secure canopy. canopy canopy set screw 9. Blade Assembly. WARNING: To reduce the risk of serious bodily injury, DO NOT use power tools to assemble the blades. If screws are overtightened, blades may crack and break. Remove blade screws and washers from top of motor housing--leave rubber cushions intact.
11. Testing Your Fan. Warranty. It is recommended that you test fan before finalizing installation. Restore power from circuit box. Test fan speeds with wall control. Start at the OFF ("0") position (no blade movement) and try each of the 5 different fan speeds. LITEX 15-YEAR LIMITED WARRANTY: LITEX INDUSTRIES, LTD. warrants this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: LITEX INDUSTRIES, LTD.
