Installation Guide

ManualsBrandsLitex ManualsCeiling FansE-BLR44ABZ5C

E163438

Installation Guide

For model:

E-BLR44ABZ5C

Table of Contents:

Safety Tips. pg. 1

Unpacking Your Fan. pg. 2

Parts Inventory. pg. 2

Installation Preparation. pg. 3

Hanging Bracket Installation. pg. 3

Fan Assembly. pgs. 4 - 5

Wiring. pg. 6

Canopy Assembly. pg. 6

Blade Assembly. pg. 7

Light Kit Assembly. pg. 7

Testing Your Fan. pg. 8

Troubleshooting. pg. 9

Warranty. pg. 9

Parts Replacement. pg. 9

net weight of fan: 13.91 lb. (6.31 kg)

PRINTED IN CHINA

READ THESE INSTRUCTIONS AND

SAVE THEM FOR FUTURE USE

Federal regulations require all ceiling

fans with light kits manufactured or

imported after January 1, 2009, to limit

total wattage consumed by the light kit

to 190W. Therefore, this fan is equipped

with a wattage limiting device.

Summary of content (10 pages)

PAGE 1
READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Federal regulations require all ceiling fans with light kits manufactured or imported after January 1, 2009, to limit total wattage consumed by the light kit to 190W. Therefore, this fan is equipped with a wattage limiting device. Installation Guide For model: E-BLR44ABZ5C Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. pgs.
PAGE 2
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. Read all instructions and safety information carefully before installing your fan and save these instructions. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2. 3. 4.
PAGE 3
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a a. canopy. 1 piece b b. hanging bracket. 1 piece c c. 4in. downrod and hanging ball (with pin & clip). 1 piece d d. motor housing. 1 piece e e.
PAGE 4
3. Installation Preparation. 12 ft. - 15 ft. (3.66m - 4.57m) blade edge 30 inches 7 feet (76cm) (2.13m) To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7ft. (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 225 square feet (20.9 square meters). 12 ft. - 15 ft. (3.66m - 4.57m) This fan can be mounted with a downrod on a normal or vaulted ceiling.
PAGE 5
. Fan Assembly (with downrod). If you wish to extend the hanging length of your fan, you must remove the hanging ball from the 4in. downrod provided to use with an extended downrod (sold separately). [If you wish to use the 4in. downrod, please proceed to instructions following the dotted line below.] To remove hanging ball, loosen set screw on hanging ball and remove the pin and clip. Lower hanging ball and remove stop pin.
PAGE 6
5. Fan Assembly (with downrod). (cont. ) With the hanging bracket secured to the outlet box and able to support the fan you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on the hanging bracket. Turn the hanging ball slot until it lines up with the hanging bracket tab. Tip: Seek the help of another person to hold the stepladder in place and to lift the fan up to you once you are set on the ladder.
PAGE 7
. Wiring. white supply wire Important: Be sure outlet box is properly grounded or that a ground wire (GREEN or Bare) is present. Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code. If you are unfamiliar with electrical wiring or if the house/building wires are different colors than those referred to below, please use a qualified electrician.
PAGE 8
9. Blade Assembly. Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades. motor housing Locate 15 blade attachment screws and washers in one of the hardware packs. Hold blade arm up to blade and align holes. Insert 3 blade attachment screws (along with washers) with fingers first and then tighten screws securely with a Phillips screwdriver. Repeat for the remaining blades.
PAGE 9
11. Testing Your Fan. It is recommended that you test fan before finalizing installation. Restore power from circuit box and light switch (if applicable). Test fan speeds with pull chain on switch housing. Start at the OFF position (no blade movement). First pull will set the fan to HI. Second pull will set the fan to MEDIUM. Third pull will set the fan to LOW. Fourth pull will again set the fan to the OFF setting. Test lights with pull chain in the middle.
PAGE 10
Warranty. Troubleshooting. Problem: Fan fails to operate. Solutions: 1. Check wall switch to fan. 2. Verify that reverse switch is set completely in either direction. 3. Check to be sure fan is wired properly. 4. Verify that male and female plugs in switch housing are connected properly. Problem: Light kit not lighting. Solutions: 1. Check wall switch to fan. 2. Check that bulbs are installed correctly. 3. Check to be sure wires in canopy are wired properly. 4.