READ THESE INSTRUCTIONS AND AND SAVE THEM FOR FUTURE USE Installation Guide For Models: E-TIT52ABZ5LKRC E-TIT52SCH5LKRC E-TIT52WW5LKRC Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. pgs. 4 - 5 Wiring. pg. 6 Canopy Assembly. pg. 6 Light Kit Assembly. pg. 7 Automated Learning Process./ Activating Code. pg. 7 Remote Control Operation. pg. 8 Testing Your Fan. pg. 8 Troubleshooting. pg.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a b c d a. canopy. 1 piece b. hanging bracket (pre-attached to canopy). 1 piece c. downrod and hanging ball (with pin and clip). 1 piece d. yoke cover.
3. Installation Preparation. To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7 feet (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square feet (37.2 square meters). 12ft. - 20ft. (3.66m - 6.1m) blade edge 30 inches 7 feet (76cm) (2.13m) 12ft. - 20ft. (3.66m - 6.1m) downrod installation This fan can be mounted with a downrod on a regular (no-slope) or vaulted ceiling.
. Fan Assembly. Remove 6 screws and washers from yoke plate (located on top plate on top of motor housing) and set aside. Lift yoke plate and top plate to remove from motor housing and set aside. yoke plate Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades. hole for reverse switch Locate 15 blade attachment screws and washers in hardware pack.
5. Fan Assembly. (cont.) Tip: To prepare for threading electrical wires through downrod, apply a small piece of electrical tape to the ends of the electrical wires--this will keep the wires together when threading them through the downrod. electrical wiring downrod canopy Loosen yoke set screws and nut at top of motor housing. Remove pin and clip from downrod (if you have not already done so). Slide downrod through canopy and then yoke cover.
6. Wiring. CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code. If you are unfamiliar with electrical wiring or if the house/building wires are different colors than those referred to in the diagram to the right, please use a qualified electrician.
. Light Kit Assembly. nodule Install one 100-watt max. halogen bulb, type JD E11 (included). Tip: Do not touch glass portion of bulb with fingers or hands. Oil from skin can cause bulb to overheat and go out prematurely. Use cardboard box or foam wrapping bulb was packed with to layer around glass portion of bulb. fitter plate bulb Align slots on glass shade with nodules on fitter plate (located on underside of motor housing).
10. Remote Control Operation. light dimmer setting button - Tap once to turn LIGHT ON or OFF. Liquid crystal display shows the amount of brightness as a percentage. Holding the button down for more than 2 seconds will cycle light through brightness settings. When turning the light back ON, light will return to the same brightness setting it was on when light was last turned OFF. fan setting light button fan button button - cycles through 3 FAN SPEEDS and then returns to the OFF setting. 11.
Troubleshooting. Warranty. LITEX LIFETIME LIMITED WARRANTY: LITEX INDUSTRIES, LTD. warrants this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will replace or repair any fan which has faulty performance due to a defect in material or workmanship. Contact Customer Service at 1-800-527-1292 to arrange for return of fan. Return fan, shipping prepaid, to Litex Industries, Ltd.