READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide For Model: RG52BNK5L RG52EB5L Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pgs. 3 - 4 Wiring. pg. 4 Fan Assembly. pg. 5 Motor Housing Assembly. pg. 5 Blade Assembly. pg. 6 Light Kit Assembly (Optional). pgs. 6 - 8 Testing Your Fan. pg. 8 Troubleshooting. pg. 9 Parts Replacement. pg. 9 Warranty. pg.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a b a. hanging bracket. 1 piece b. motor housing. 1 piece c. motor assembly. 1 piece c d. light kit fitter. 1 piece d e.
3. Installation Preparation. 12ft. - 20ft. (3.66m - 6.1m) blade edge 30 inches 7 feet (76cm) (2.13m) To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7ft. (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square feet (37.2 square meters). 12ft. - 20ft. (3.66m - 6.
4. Hanging Bracket Installation. (cont.) Install hanging bracket to outlet box using original screws, spring washers and flat washers provided with new or original outlet box.* Pull electrical wiring from outlet box through center hole in the hanging bracket. hanging bracket *Note: It is very important that you use the proper hardware when installing the hanging bracket as this will support the fan. spring washers flat washers outlet box screws 5. Wiring.
. Fan Assembly. Remove motor assembly from j-hook on hanging bracket. Lift motor assembly to hanging bracket and carefully push wiring and wire connectors into outlet box. Align holes in top of motor assembly with bolts in hanging bracket and push up so that bolts come through holes. Secure motor assembly with flat washers and motor mounting nuts that were previously removed, page 3, step 4. WARNING: It is extremely important to tighten motor mounting nuts completely so that fan is mounted securely.
8. Blade Assembly. WARNING: To reduce the risk of serious bodily injury, DO NOT use power tools to assemble the blades. If overtightened, blades may crack and break. Locate 15 blade attachment screws/washers in one of the hardware packs. Hold blade arm up to blade and align holes. Insert 3 blade attachment screws/washers with fingers first and then tighten screws securely with a Phillips screwdriver. Repeat procedure for the remaining blades. Remove blade arm screws and lock washers from underside of motor.
9. Light Kit Assembly (Optional). (cont.) To attach light kit fitter to motor assembly, align holes in switch housing cap with holes in switch housing and re-insert 3 screws previously removed. (Note: Make sure to align gap on edge of switch housing cap with reverse switch on switch housing for a correct fit.) Secure all screws with a Phillips screwdriver. Install 3 medium base 6.5 watt LED bulbs (included).
. Light Kit Assembly (Optional). (cont). Locate cap in one of the hardware packs and place cap firmly into hole in middle of switch housing cap. motor housing switch housing Align holes in switch housing cap with holes in switch housing. Secure switch housing cap with 3 screws and star washers that were removed at the beginning of Section 9, page 6. Tighten all 3 screws securely. switch housing cap cap 10. Testing Your Fan.
Troubleshooting. Warranty. Problem: Fan fails to operate. Solutions: 1. Check wall switch to fan. 2. Verify that reverse switch is set completely in either direction. 3. Check to be sure fan is wired properly. Problem: Light kit (optional) not lighting. Solutions: 1. Check wall switch to fan. 2. Check that bulbs are installed correctly. 3. Verify that wires in outlet box are wired properly. 4. Verify that molex connections in switch housing are connected properly.
