Specification Sheet

DOWNLIGHTING 6BP-6OP LED
FEATURES & SPECIFICATIONS
INTENDED USE — Our recessed LED module is the most economical means to create a well lit environ-
ment with exceptional energy eciency and near zero maintenance. Great for retrot into existing
downlight cans or new construction and remodel applications. Unique torsion spring and friction clip
retention allows tment into nearly 100% of installed cans. The LED module maintains at least 70%
light output for 50,000 hours.
CONSTRUCTION — Aluminum die cast reector with deep bae conguration for reduced glare.
Combined LED and driver printed circuit board attached. Inner reector cone funnels light through the
pressed-in diused lens.
Bae and open trim inserts are available in multiple nishes.
OPTICS — Diused lens at end of mixing chamber to provide even light distribution for general illumina-
tion, equivalent to 65W BR30 or 100W BR30 lamp.
Wide ood beam angle at >45°.
ELECTRICAL — Center 2 Edge™ (patent pending) technology created for a single point source. Primary
power disconnect provided for simple connection to a dedicated LED connector in the housing.
Dimming down to 10%. For compatible dimmers, refer to Compatible Dimmers Chart.
725-lumen P series has an input wattage of 12.7 watts, 57 lumens per watt, equivalent to 65-watt
incandescent.
P Series’ patent pending driver has zero inrush, which allows power loads to be calculated with actual
rated wattages.
Example: 47 units of 6BPMW LED xtures can be installed in line with a 600-watt dimmer. 600W/12.7W
= 47 xtures.
950-lumen P series has an input wattage of 15.2 watts, 63 lumens per watt, equivalent to 100-watt
incandescent.
*Actual wattage may dier by +/-5% when operating at 120V +/-10%.
INSTALLATION  Suitable for installation in standard and shallow-height rough-in sections.
E26 socket adapter and splice kit ships standard. This enables easy installation or permanent conversion
to an LED source for Title 24 compliance.
Twin torsion springs ensure easy installation.
Friction clips included to allow tment into cans without torsion brackets from an inside diameter of
6.0” to 7.0”.
LISTINGS — CSA certied to US and Canadian safety standards. ENERGY STAR® qualied; California
T24 compliant. Wet location listed for indoor use only. WSEC ASTM E283 for Air-Tight (with IC housings).
WARRANTY — 5-year limited warranty. Complete warranty terms located at
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Actual performance may dier as a result of end-user environment and application.
Note: Specications subject to change without notice.
PATENTS PENDING.
Accessories: Order as separate catalog number.
TSA6 Makes non-bracket housing compatible with the LED module; ships as units, J6 or J25
FL2LED Makes L7XF housings compatible with the LED module
Torsion mount shown
Friction clip shown
(included)
5-7/8
(14.9)
3-7/
8
(9.8
)
7-5/8
(19.4)
Specications
Aperture: 5-7/8 (14.9)
Ceiling opening: Determined by rough-in
Overlap trim: 7-5/8 (19.4)
Height: 3-7/8 (9.8)
LED Recessed Downlighting
6BP/6OP
6” LED Module
IC/Non-IC
Retrot
D
I
M
M
A
B
L
E
E26 adaptor
(included)
Splice kit
(included)
All dimensions are inches (centimeters) unless otherwise indicated.
Notes
1 Total system delivered lumens.
2 Must be ordered on a separate line.
See page 2 for Trim Inserts.
ORDERING INFORMATION
Lead times will vary depending on options selected. Consult with your sales representative.
Example: 6BP TRMW LED 27K 90CRI
Series/Finish Lamp CCT / CRI / W / Lumens
1
Voltage Options
6BPMW 6" Bae LED module, matte white
6BP TRMW 6" Bae LED module, black bae, matte
white ange
6BPBN 6" Bae LED module, brushed nickel
6BPORB 6" Bae LED module, oil-rubbed bronze
LED
HL LED
(blank) 3000 K / 83 CRI / 12.7W / 725L
27K 90CRI 2700 K / 93 CRI / 11.2W / 600L
30K 90CRI 3000 K / 93 CRI / 11.2W / 600L
40K 90CRI 4000K / 92CRI / 9.9W / 650L
(blank) 3000 K / 83 CRI / 15.2W / 950L
27K 90CRI 2700 K / 93 CRI / 16.5W / 860L
30K 90CRI 3000 K / 93 CRI / 16.5W / 860L
40K 90CRI 4000K / 92CRI / 16.4W / 950L
(blank) 120V L7XLED T24 New construction rough-in LED base
L7XRLED T24 Remodel rough-in LED base
LC6LED T24 New construction rough-in LED base
L7X New construction rough-in
2
L7XR Remodel rough-in
2
L7XP New construction shallow rough-in
2
L7XPR Remodel shallow rough-in
2
LC6 New construction rough-in
2
LCP New construction shallow rough-in
2
6OPA 6" Open LED module, clear diuse
6OPAZ 6" Open LED module, clear specular
6OPA TRMW 6" Open LED module, clear diuse, matte
white ange
6OPAZ TRMW 6" Open LED module, clear specular, matte
white ange
LED
HL LED
(blank) 3000 K / 83 CRI / 12.7W / 725L
27K 90CRI 2700 K / 93 CRI / 11.2W / 600L
30K 90CRI 3000 K / 93 CRI / 11.2W / 600L
40K 90CRI 4000K/ 92CRI / 9.9W / 650L
(blank) 3000 K / 83 CRI / 15.2W / 950L
27K 90CRI 2700 K / 93 CRI / 16.5W / 860L
30K 90CRI 3000 K / 93 CRI / 16.5W / 860L
40K 90CRI 4000K/ 92CRI / 16.4W / 950L
(blank) 120V L7XLED T24 New construction rough-in LED base
L7XRLED T24 Remodel rough-in LED base
LC6LED T24 New construction rough-in LED base
L7X New construction rough-in
2
L7XR Remodel rough-in
2
L7XP New construction shallow rough-in
2
L7XPR Remodel shallow rough-in
2
LC6 New construction rough-in
2
LCP New construction shallow rough-in
2
Catalog
Number
Notes
Type