Installation Guide

Page 3 of 6
4. Press and hold the ON / OFF Button (11) until you hear an
audible 4-tone, high-to-low chime to turn off the Speaker (4).
5. Remove Power Plug (17) from the AC120V electrical outlet,
then disconnect the plug from the xture.
6. Conrm the unit is in MASTER MODE by ensuring the S-M
Switch (10) is toggled towards the letter “M” on the back of
the Speaker (4) (Figure 2).
7. Wake the Speaker (4) from SLEEP MODE by pressing
the ON / OFF Button (11) for 2 seconds until you hear an
audible tri-tone, low-to-high chime. The PAIR Button (12) will
start blinking GREEN, and the S-M Indicator Light (5) will
blink BLUE on the front of the module under the speaker
grill. This indicates the speaker is in MASTER MODE and is
ready to pair (Figure 3).
8. Place your Bluetooth® Enabled Device (2) (phone, laptop,
music player, etc.) in SEARCH MODE, then select the device
called Down Light Speaker to pair to the Speaker (4).
9. Pairing complete with an audible BEEP sound. Play music from
your Device (2) to check operation of the MASTER Unit (1).
10. If the pair does not complete within 20 seconds, press and
hold the ON / OFF Button (11) until you hear an audible
4-tone, high-to-low chime indicating that the Speaker (4) is
in SLEEP MODE. After the BLUE S-M Indicator Light (5)
turns off completely under the speaker grill, re-start process
from Step I.7.
11. To stop playing music, pause or turn music off on your
Device (2). You do not need to turn the unit OFF.
Note:
• Once the MASTER Unit (1) is paired, the S-M Indicator Light
(5) will stop blinking, and become a solid BLUE light.
• If there is no Bluetooth® signal detected, the MASTER Unit
Speaker (4) will automatically shut down into SLEEP MODE
after 30 minutes.
• The MASTER Unit (1) will re-pair to the last Device (2)
connected to it when it wakes up from SLEEP Mode by toggling
the light switch.
• Only one Device (2) can be connected to a MASTER Unit (1)
at a time. To play music from a different Device, disconnect the
rst Device then re-pair MASTER Unit to different Device by
completing Steps I.8-I.9.
Step II: Sync additional SATELLITE Units (3) to MASTER
Unit (1) (Complete Prior to Install)
Note: Pair the speakers close to each other on a table top prior
to installing to permanent locations. This makes it easier to pair
the speakers since they are close together and you can see
the color of the Indicator Lights (5 & 6) on each unit. Play music
during the pairing process for easy identication and to ensure
the connection is successful.
1. Complete Steps I.1 - I.5.
2. Activate SATELLITE MODE by toggling the S-M Switch (10)
on each SATELLITE Unit (3) towards the letter “S” of the
“S-M” icon (Figure 2).
3. Turn ON the SATELLITE Unit (3) by pressing the ON / OFF
Button (11) for 2 seconds. The PAIR Button (12) will illuminate
GREEN, with an audible BEEP sound. The S-M Indicator
Light (5) under the speaker grill will also illuminate GREEN
indicating SATELLITE MODE (Figure 3).
4. While the MASTER Unit (1) is still playing music, press the
PAIR Button (12) on the SATELLITE Unit (3) until it makes
an audible BEEP sound and starts quickly ashing GREEN.
Then separately press and hold the PAIR Button on the
MASTER Unit.
5. Once speakers pair, the SATELLITE Unit (3) will make an
audible BEEP sound and should sync up with the MASTER
Unit (1) within 20 seconds, resulting in music coming from
both units simultaneously. The PAIR Button (12) on both
units will illuminate to a solid GREEN light and will remain
solid GREEN as long as the units are paired.
6. If the pairing does not complete within 20 seconds, turn OFF
the SATELLITE Unit (3) by pressing the ON/OFF Button (11)
for 3 seconds. After the Speaker (4) makes two BEEP BEEP
sounds, re-start process from Step II.3.
7. Repeat Steps II.1 - II.5 for up to seven SATELLITE Units (3)
(Figure 4).
Note:
• If the music from your Device (2) is turned off, then the
SATELLITE Unit (3) will be in STAND-BY MODE continuously
waiting for a signal from the MASTER Unit (1).
INSTALLATION INSTRUCTIONS
This device is not intended for use with emergency exits or
emergency lighting.
CAUTION - The battery used in this device may present a risk of
re or explosion when heated above 60°C (140°F) or incinerated.
WARNING - risk of re or electric shock. Installation of this retrot
assembly requires a person familiar with the construction and
operation of the luminaire’s electrical system and the hazards
involved. If not qualied, do not attempt installation, contact a
qualied electrician.
WARNING - risk of re or electric shock. Install this kit only
if the construction and features of the luminaire matches the
construction and features shown in the drawings. Do not use if
enclosure is broken.
WARNING - to prevent wiring damage or abrasion, do not expose
wiring to edges of sheet metal or other sharp objects.
Do not make or alter any open holes in an enclosure of wiring or
electrical components during kit installation.
WARNING - Changes or modications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE - This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Radiation Exposure Statement: This equipment complies with
Canada radiation exposure limits set forth for uncontrolled
environments. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
6” Speaker Downlight, Models 6SL RD 07LM 30K 90CRI MW, 6SL
RD 07LM 27K 90CRI MW, & 6SL RD 07LM 40K 90CRI MW, Input
120V 60Hz
Stream music from your Bluetooth® enabled device up to 30 ft.
away, Connect up to 8 speaker lights, 5W audio output, app not
required for use.
Each unit carton contains 1ea LED module with built-in speaker
assembly, 1ea E26 socket adapter, 1ea power plug, and instructions.
Required Tools (not included): safety glasses, ladder, and gloves.
Step I: Pairing MASTER Unit (1) (Complete Prior to Install)
Note:
• Every speaker downlight is preset as a MASTER Unit (1), but
can be set as a MASTER Unit (1) or a SATELLITE Unit (3) by
toggling the S-M Switch (10).
• Pair the MASTER Unit (1) to your Bluetooth® enabled device (2)
on a table top prior to installing to permanent location. This makes
it easier to pair the Speaker (4) and see the color of the Indicator
Lights (5 & 6) on the unit. Play music during the pairing process
for easy identication and to ensure the connection is successful.
1. Remove Protective Tab (9) from Battery Cover (8) on back
of Speaker (4) (Figure 2).
2. Conrm Orange Connector (14) of Power Plug (17) is
connected to the xture’s mating Orange Connector (14), and
then connect the plug to an AC120V electrical outlet (Figure 1).
3. Press ON / OFF Button (11) for 2 seconds until you hear an
audible tri-tone, low-to-high chime. The PAIR Button (12) will
start blinking GREEN. This indicates the Speaker (4) has
been activated (Figure 2).
• Once a SATELLITE Unit (3) pairs to a MASTER Unit (1),
it will be very loyal to THAT MASTER Unit. To release the
SATELLITE Unit from its paired MASTER Unit, complete either
of the following two actions:
A. Pair the SATELLITE Unit to a different MASTER Unit.
(i.e., take another MASTER Unit to override this paired
SATELLITE Unit from its existing paired MASTER Unit) by
completing Steps II.3-II.5.
B. Shut the SATELLITE Unit off, and then set it in MASTER
MODE by toggling the S-M switch towards the letter “M” on
the back of the speaker, then use it as MASTER Unit by
completing Steps I.7-I.9.
Step III: Prepare for Installation
1. Ensure input power is 120V, 60Hz, supply wires are rated
for at least 90°C (194°F), and power is disconnected
by turning OFF the circuit breaker or by removing the
appropriate fuse at the fuse box.
2. If necessary, remove old ballast.
Step IV: Determine Wiring Method (Select one wiring method)
A. E26 Socket Adapter (13) (Figure 5):
1. Screw Adapter (13) into the base socket inside Housing
(15).
2. Plug Orange Connector (14) of Adapter (13) into the
xture’s mating Orange Connector (14). Or,
B. LED Connector (Figure 6):
1. Plug Orange Connector (14) from the xture into the
mating LED connector inside Housing (15).
Note: No Hardwire Connection Kit is supplied with xture.
Step V: Installation of Unit(s) into Recessed Housing(s)
1. Squeeze legs of each Torsion Spring (16) together and
seat them inside the torsion brackets of the Housing (15).
Release springs, and gently push module into housing until
ush with ceiling.
2. Repeat Step V.1. for each additional unit. Ensure Satellite
Units (3) are located within 60 ft. of the Master Unit (1).
Step VI: Reconnect Device
Note: If MASTER Unit (1) loses Bluetooth® connection, or is
disconnected, the S-M Indicator Light (5) under the grill will blink
BLUE for 30 minutes until it shuts down into SLEEP MODE.
1. To listen to music again, wake MASTER Unit (1) from
SLEEP MODE by toggling the light switch or dimmer (turn
ON + turn OFF or turn OFF + turn ON).
2. After you hear the audible chime and see the S-M Indicator
Light (5) blinking BLUE, repeat Steps I.8-I.9 to reconnect
your Device (2) to the MASTER Unit (1) Speaker (4).
Step VII: Charge the Battery
1. To recharge the battery, turn the xture light ON. The
Charging Indicator Light (6) under the speaker grill will
illuminate RED to indicate the Speaker (4) is receiving
power and is re-charging.
Note:
• When the xture light is turned OFF, the Speaker (4) runs on
battery power and has a 6-hour battery life.
• It takes approximately 4 hours to fully charge the speaker.
RECOMMENDED DIMMING SWITCHES: The LED Modules are
compatible with several standard residential dimmers. A list of
recommended dimmers can be found at www.acuitybrands.com,
keyword search 6SL. Exclusion from the list does not mean
a dimmer will not work in conjunction with your LED module.
Consult with your dimmer manufacturer regarding compatibility.
RECESSED CAN COMPATIBILITY: Lithonia’s 6SL modules
are tested to t in a minimum enclosure of 6” diameter by 6”
height, with a maximum ange diameter of 7.5”. For a list of
compatible housings go to www.acuitybrands.com, keyword
search 6SL.