Specification Sheet

900 Northrop Road, Wallingford, CT 06492 • 1.800.PASSIVE • FX 203.269.9621 • www.sensorswitch.com
WARRANTY: Sensor Switch, Inc. warrants these products to be free of defects in manufacture and workmanship for
a period of 60 months. Sensor Switch, Inc., upon prompt notice of such defect, will, at its option, provide a Returned
Material Authorization number and repair or replace returned product.
LIMITATIONS AND EXCLUSIONS: This Warranty is in full lieu of all other representation and expressed and
implied warranties (including the implied warranties of merchantability and tness for use) and under no circumstances
shall Sensor Switch, Inc. be liable for any incidental or consequential property damages or losses.
TS-CM-002A
Revised 03.26.12 © 2012 Sensor Switch
INSTALLATION
WIRING (DO NOT WIRE HOT)
COVERAGE PATTERN
6 HIGH BAY 360º LENS
STANDARD WIRING
RED - Power Input (12-24 VAC/VDC)
BLACK - Common
WHITE - Occupancy State (high VDC for occupied)
RELAY OPTION (R)
GRAY / BROWN - Connected during occupied state
VIOLET / BROWN - Connected during unoccupied state
Note: Relay is energized during unoccupied state
PHOTOCELL/DIMMING OPTIONS (D, P)
BLUE - Direct output to power pack for providing photocell
control and/or secondary dim time out. Output is high VDC
with occupancy & low light. Output also held high during
secondary dim time out. For multi-level control, use two
power packs and connect White wire to primary load and
Blue to daylight load.
VIOLET w/ WHITE STRIPE - Connect to 0-10 VDC control
wire (typically Violet) from 0-10 VDC dimmable ballast
GRAY from Ballast - Connect to sensor Black wire
• Best choice for 15 to 45 ft (4.57 to 13.72 m) mounting heights
• 15 to 20 ft (4.57 to 6.10 m) radial coverage overlaps area lit
by a typical high bay xture
• Excellent detection of large motion (e.g. walking) up to a 35
ft (10.76 m) mounting height
• Excellent detection of extra large motion (e.g. forklifts) up
to a 45 ft (13.72 m)mounting height
PUSH BUTTON
PROGRAMMING
Refer to instruction card IC7.001 for default settings and directions on programming the sensor via the push-button.
• Mount sensor directly to a ceiling tile or a metallic grid (two
self-tapping screws provided).
• Sensor’s mounting holes also align with 3.5” octagon or
single gang handy box (screws not provided).
• Sensor will detect motions crossing segments more
effectively than motions parallel to beams.
• For optimal detection, position sensor such that segments
are crossed upon entrance and unable to view outside the
space.
30 20 10 0 ft 10 20 30
9.1 6 3 0 m 3 6 9.1
0 ft
10
20
30
40
50
0 m
3
6
9.1
12.2
15.2
LOW VIEW
HIGH VIEW
0 ft
15
0 m
4.6
20 10 0 ft 10 20
6 3 0 m 3 6
30 20 10 0 ft 10 20 30
9.1 6 3 0 m 3 6 9.1
0 ft
10
20
30
40
50
0 m
3
6
9.1
12.2
15.2
LOW VIEW
HIGH VIEW
0 ft
15
0 m
4.6
20 10 0 ft 10 20
6 3 0 m 3 6
[R] Relay Option
[D] Dimming Option
POWER PACK
(PP20)
RED
WHT
BLK
VIO w/ WHT STRIPE (+)
(-)
[D, P] Photocell / Dimming Options