Specification Sheet

®
SPECIFICATIONS
ORDERING INFO
OPTIONS
OCCUPANCY CONTROLLED
DIMMING (D)
• Provides dimming output to control
0-10 VDC dimmable ballasts
• Provides a second occupancy time-
out period that enables the lights to go
to a dim setting before turning off
• Adjustable max/min dim setting
PHOTOCELL (P)
• Auto set-point calibration
• Two selectable modes of operation
• On/Off mode: Photocell has full
control during periods of occupancy
• Inhibit mode: Photocell can prevent
lights from turning on if adequate
daylight is available, but cannot turn
lights off
PHOTOCELL W/ DIMMING (ADC)
• Photocell within sensor maintains total
room light level by controlling levels of
0-10 VDC dimmable ballasts
• Photocell also has full on/off control
during periods of occupancy
• Provides a second occupancy time-
out period that enables the lights to go
to a dim setting before turning off
Note: LampMaximizer+ features not
available with ADC option
347 VAC (347)
• Allows sensor to be powered from
and switch 347 VAC
LOW TEMP/HIGH HUMIDITY (LT)
• Sensor is corrosion resistant to
moisture
• Operates down to -40º F/C
OVERVIEW
The CMRB 9 Series Standard Range occupancy
sensor mounts directly to the end of a luminaire
and utilizes the industry’s leading Passive
Infrared (PIR) technology to provide amazing
sensitivity to small motions and excellent
payback. The sensor is line powered and can
switch loads directly without the need for a power
pack. A CMRB 9 is typically installed on each
xture when used in long corridors with concrete
ceilings and pendant or surface xtures spaced
10-20 ft (3.05-6.10 m) apart. This approach
maximizes energy savings and may be more
cost effective than running low voltage wiring.
When mounting above 15 ft (4.57 m) the CMRB
6 Series is a better option than the CMRB 9;
and when mounting below 8 ft (2.44 m) or for
greater radial coverage the CMRB-10 Series
should be alternatively considered. Additionally,
for areas with obstructions, the CMRB PDT 9 is
recommended.
SENSOR OPERATION
The sensor detects changes in the infrared
energy given off by occupants as they move
within the eld-of-view. When occupancy is
detected, a self-contained relay switches the
connected lighting load on. The sensor is line
powered, switches line voltage, and requires no
eld calibration or sensitivity adjustments.
LAMPMAXIMIZER
®
This sensor also contains patent pending
LampMaximizer technology that allows users
to aggressively target energy savings while still
protecting lamp life. A minimum on timer, factory
set at 15 minutes, helps preserve lamp life by
eliminating all lamp cycles shorter than lamp
manufacturers’ recommendations.
A standard occupancy time delay is also present
that ensures lights turn off (assuming minimum
on timer has elapsed) if no occupancy is
detected. This timer is factory set at 10 minutes
to promote energy savings, but is adjustable
between 30 seconds and 20 minutes. These
adjustments can be done manually, through
the unit’s push-button, or automatically every
two weeks through an advanced mode, called
LampMaximizer+, that determines the optimum
time delay in order to maximize both lamp life
and energy savings. Additionally, this sensor
maintains statistics on total lamp on time and
number of cycles.
STANDARD RANGE 360º SENSOR
FIXTURE MOUNT BOX • LINE VOLTAGE • PASSIVE INFRARED (PIR)
CMRB 9
FEATURES
100% Digital PIR Detection,
Excellent RF Immunity
360º Coverage Pattern
Self-Contained Relay,
No Power Pack Needed
No Minimum Load Requirements
Interchangeable Hot & Load Wires,
Impossible to Wire Backwards
Push-Button Programmable
Adjustable Time Delays
No Field Calibration or Sensitivity
Adjustments Required
Convenient Test Mode
100 hr Lamp Burn-in Timer
Green LED Indicator
LAMPMAXIMIZER
®
TECHNOLOGY
• Protects Lamp Life while
Maximizing Energy Savings
• Minimum On Timer (15 min default)
• Occ. Time Delay (10 min defatult)
• LampMaximizer+ Mode -
Optimizes Lamp Life & Energy
Savings (disabled by default)
• Switch Counter (in 1000’s)
• Total Lamp On Time (in khrs)
PHYSICAL SPECS
SIZE 3.63”H x 3.63” W x 1.5” D
(9.22 cm x 9.22 cm x 3.81 cm)
WEIGHT 6 oz
MOUNTING 1/2” knockout
COLOR White
ELECTRICAL SPECS
MAXIMUM LOAD
800 W @ 120 VAC
1200 W @ 277 VAC
1500 W @ 347 VAC
MINIMUM LOAD None
MOTOR LOAD 1/4 HP
FREQUENCY 50/60 Hz
DIMMING LOAD Sinks < 20mA;
~40 Ballasts @ .5mA each
ENVIRONMENTAL SPECS
OPERATING TEMP
14º to 160º F (-10º to 71º C)
STORAGE TEMP
-14º to 160º F (-26º to 71º C)
RELATIVE HUMIDITY
20 to 90% non-condensing
SILICONE FREE
ROHS COMPLIANT
VOLTAGE
TEMP/HUMIDITY
Blank = None Blank = 120/277 VAC Blank = Standard
D = Occupancy Controlled Dimming 347 = 347 VAC LT = Low Temp
P = Photocell
ADC = Photocell w/ Dimming
CMRB 9 [DIMMING/PHOTOCELL] [VOLTAGE] [TEMP/HUMIDITY]
DIMMING / PHOTOCELL CHOOSE ONE ONLY
C US LISTED
TITLE 24
MADE in U.S.A.
5 YEAR WARRANTY