Specification Sheet

FEATURES & SPECIFICATIONS
INTENDED USE
The sleek design of the D-Series Size 2 Flood reflects the embedded high performance LED
technology. It is ideal for larger signage, facade and flagpole lighting in many commercial and
residential applications.
CONSTRUCTION
Die-cast aluminum housing has integral heat sink fins to optimize thermal management through
conductive and convective cooling. The LED driver is mounted in direct contact with the casting
to promote low operating temperature and long life. Housing is completely sealed against
moisture and environmental contaminants using a tempered glass lens (IP66). Low EPA (0.8 ft
2
) for
optimized wind loading.
FINISH
Exterior parts are protected by a zinc-infused Super Durable TGIC thermoset powder coat finish
that provides superior resistance to corrosion and weathering. A tightly controlled multi-stage
process ensures a minimum 3 mils thickness for a finish that can withstand extreme climate
changes without cracking or peeling.
OPTICS
A variety of precision-molded vacuum-metallized specular reflectors are engineered for superior
target illumination, uniformity and spacing. Light engines are available in 3000K (70 CRI min.),
4000K (70 CRI min.) or 5000K (70 CRI min.) configurations. Optional visors offer additional
versatility.
ELECTRICAL
Light engine(s) consist of chip-on-board (COB) LEDs directly coupled to the housing to
maximize heat dissipation and promote long life (100,000 hrs, L80). Class 1 electronic driver
has a power factor >90%, THD <20%, and has an expected life of 100,000 hours with <1%
failure rate. Standard 6KV surge protection meets a minimum Category C Low operation (per
ANSI/IEEE C62.41.2).
INSTALLATION
Integral adjustable knuckle with 1/2-14 NPS threaded pipe, tenon slipfitter, or yoke
mounting, facilitates quick and easy installation to a variety of mounting accessories. This
secure connection enables the D-Series Size 2 to withstand up to a 1.5 G vibration load rating
per ANSI C136.31.
LISTINGS
CSA certified to U.S. and Canadian standards. Luminaire is IP66 rated. Rated for -40°C
minimum ambient.
DesignLights Consortium
®
(DLC) Premium qualified product and DLC qualified product. Not
all versions of this product may be DLC Premium qualified or DLC qualified. Please check
the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are
qualified.
WARRANTY
5-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx.
Note: Actual performance may differ as a result of end-user environment and application.
All values are design or typical values, measured under laboratory conditions at 25 °C.
Specifications subject to change without notice.
One Lithonia Way • Conyers, Georgia 30012 • Phone: [phone] • www.lithonia.com
© 2012-2016 Acuity Brands Lighting, Inc. All rights reserved.
DSXF2-LED
Rev. 11/14/16
Mounting, Options and Accessories
THK - Knuckle with
1/2” NPS threaded pipe
IS – Integral sliptter
H= 2-1/2” (6.3 cm)
ID= 2-3/8” (6.0 cm)
OD= 3-1/2” (8.8 cm)
UBV – Upper/bottom visor
W= 10” (25.4 cm)
H= 2-1/2” (6.3 cm)
D= 3” (7.6 cm)
FV – Full visor
W= 10” (25.4 cm)
H= 2-1/2” (6.3 cm)
D= 3” (7.6 cm)
YKC62 - Yoke with SO cord
W= 4-3/4” (12.0 cm)
H= 4-1/4” (10.7 cm)
D= 2-1/4” (5.7 cm)
VG – Vandal guard
W= 10-1/2” (26.6cm)
H= 4“ (10.1cm