Installation Guide

INSTALLATION INSTRUCTIONS - ENGLISH
INSTALLATION INSTRUCTIONS
Trouble Shooting Guide
If this fi xture fails to operate properly, use the guide below
to diagnose and correct the problem.

 Verify that fi xture is wired properly.
 Verify that fi xture is grounded correctly.
 The line voltage at the fi xture is correct.
If further assistance is required, contact:
Technical Support at: [phone]
This LED light provides low maintenance service with no
bulbs to change.
Cleaning Diffuser: For best results, diffusers should be
washed with soap or mild detergent. Rinse with clear water
and allow to air dry.

• Fixture cannot be used with a dimmer switch.
• This fi xture is designed for indoor use ONLY
and should not be used in areas with limited
ventilation or high ambient temperatures.
• Fixture must be connected to a nominal 120Volt,
60 Hz power source. Any other connection
voids warranty.
• This fi xture is intended to be connected to a
properly installed and grounded UL listed
junction box (not provided) and should be
installed according to NEC and local building
codes.
• Fixture must be secured to mounting surface with
mounting hardware appropriate to your application.
1. Remove fi xture components and parts pack(s). Check that
all parts are included. See Page 2.
2. Remove two screws (4) securing the wireway cover (2) to
the Fixture Housing (1) See Fig 1.
3. Remove 7/8” knockout at center of fi xture by placing straight
blade screwdriver on knockout and striking sharply with
hammer (Always wear safety glasses when hammering).
Remove slug by fl exing back and forth with pliers. See
Fig 2.
WARNING: Before wiring fi xture to the power supply, turn off
electricity at fuse or circuit breaker box. Fixture must be ground-
ed to avoid potential electrical shock and to ensure reliable lamp
starting.
4. With power turned off, lift fi xture housing to ceiling, center-
ing over outlet box and parallel to walls. Mark ceiling with
pencil for mounting holes through 1/4” x 3/8” slots. Drill
1/8” pilot hole at each location.
If drill encounters ceiling joist, hold fi xture up to outlet box and
pull electrical supply wires into fi xture through the knockout hole,
use wood screw (not supplied) at each end of the fi xture body to
secure to ceilingjoist. See Fig 4.
If drill does not encounter ceiling joist, enlarge hole in ceiling to
accommodate toggle bolt (not supplied). Hold fi xture up to outlet
box and pull electrical supply wires into the fi xture through the
knockout hole, insert and tighten toggle bolts.
See Fig 3.
5. Ground fi xture as follows. Connect the green or bare copper
ground wire from the outlet box under the green ground
screw. If house wiring includes no ground wire, consult your
local electrical code for approved methods. See Fig 5.
6. Connect white fi xture wire(s) to white power supply wire with
wirenut. Connect black fi xture wire(s) to black power supply
wire with wirenut.
FOR PROPER CONNECTION, PLACE WIRENUT
OVER WIRES, TWIST CLOCKWISE UNTIL TIGHT.
Note: Make sure no wires are exposed.
7. Replace wireway cover under tabs on one side of fi xture
housing. Make sure wires are not pinched between fi xture
housing and wireway cover. Secure ends of wireway cover
with screws (4).
8. To install Foam Tape( 6), place Diffuser Frame (5) on fl at
surface with diffuser side down. Peel backing from tape (6)
to expose adhesive. Start applying tape at corner and
proceed around perimeter of frame (5). Cut off any excess
material- See Fig.6
9. To install Frame Bracket (7), align two holes in bracket with
two holes in Diffuser Frame (5). Secure with Frame Bracket
Screws (8) provided. Do not over tighten screws, could
damage frame. See Fig. 7
Page 3
10. To install Diffuser Frame (5), angle end opposite the
Bracket (7) downward, then insert bracket (7) between
Fixture Housing (1) and ceiling. Pivot upward and secure
with Frame Screw (9) provided. Do not over tighten screw,
could damage frame. See Fig 8
11. Turn on electricity at fuse or circuit breaker box.