Installation Guide

ManualsBrandsLithonia Lighting ManualsCommercial LightingContractor Select FMLWL 4 ft. 2000/3000/4000 Lumens Integrated LED White Linkable Wraparound Light Fixture

INSTALLATION INSTRUCTIONS

Linkable LED Wrap

TOOLS REQUIRED

FOR INSTALLATION

• Safety glasses

• Drill with 1/16” drill bit

• Phillips screwdriver

• Pencil

• Hammer

• Pliers

• Ruler

• Wire Strippers

OUTILS REQUIS POUR L’INSTALLA

TION

• Lunettes de sécurité

• Perceuse, avec un foret de 1/16 po

• Tournevis à tête Phillips

• Crayon

• Marteau

• Pinces

• Régle

• Outil à dénuder

HERRAMIENTAS NECESSARIAS PARA

LA INSTALACIÓN

• Lentes de seguridad

• Taladro con broca de 1/16”

• Destornillador de Phillips

• Làpiz

• Martillo

• Pinzas

• Regla

• Pelacables

U219789T Rev C 1/21

Protect yourself. Before installing,

read these instructions carefully and

save them for future reference.

Date Installed:________________

Pour votre propre protection. Avant de procéder

à l’installation, veuillez lire attentivement ces

directives et les conserver pour référence ultérieure.

Date de l’installation :

________________

Protéjase. Antes de instalar, lea estas

instrucciones cuidadosamente

y guárdelas para futura referencia.

Fecha Instalada:________________

FMLWL LNK 48 ALO4 8SWW2 (48” LED Wrap)

Actual Dimensions: 5-1/2”W x 2-5/8”H x 47-3/8”L

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Linkable LED Wrap FMLWL LNK 48 ALO4 8SWW2 (48” LED Wrap) AN AR G • • • • • • • • IMITÉE* IE L Safety glasses Drill with 1/16” drill bit Phillips screwdriver Pencil Hammer Pliers Ruler Wire Strippers A • • • • • • • • Pour votre propre protection. Avant de procéder à l’installation, veuillez lire attentivement ces directives et les conserver pour référence ultérieure.
PAGE 2
LED IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION • To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels. • Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
PAGE 3
7 1 5 2 6 9 3 4 8 FIXTURE PACKING LIST LISTA DE EMBALAJE Description Quantity 1) Housing Assembly ........................................ 1 2) Diffuser ............................................................... 1 3) Wirenut* ............................................................ 3 4) Junction Box Mounting Screws* ............... 2 5) Switch.................................................................. 1 6) “Keyed” Connector Port ................................
PAGE 4
PREPARING THE FIXTURE FOR INSTALLATION The FMLWL ALO/CCT/LNK fixture has a Switchable CCT feature and a ALO (Adjustable Lumen Output) feature. Select from any of the 3000K/4000K/5000K CCT options and 2000lm/3000lm/4000lm light output options. Please refer to the section CCT/ALO Selection to adjust the switches. The CCT switch is preset at 4000K and the ALO switch is preset at 3000lm from the factory. Note: Turn off power at circuit breaker box! Figure 1 Direct-Wire Method 1.
PAGE 5
PRÉPARATION DE L’APPAREIL POUR L’INSTALLATION PREPARÁNDOSE PARA LA INSTALACIÓN La luminaria FMLWL ALO/CCT/LNK tiene una función CCT conmutable y una función ALO (salida de lumen ajustable). Seleccione entre cualquiera de las opciones CCT 3000 K/4000 K/5000 K y las opciones de salida de luz de 2000 lm/3000 lm/4000 lm. Consulte la sección Selección CCT/ALO para ajustar los interruptores. El interruptor CCT está preestablecido en 4000 K y el interruptor ALO está preestablecido en 3000 lm de fábrica.
PAGE 6
10. Install diffuser (2) - Note: remove tape from diffuser prior to installing diffuser. Starting at one end of housing, insert diffuser slot onto edge of housing. Carefully squeeze diffuser to engage opposite side with housing. Continue this action down length of diffuser until fully installed onto housing. Screw Hole Location 11. If installing additional satellite units, proceed to follow the Row Connector Method instructions. 12.
PAGE 7
9. Vuelva a instalar la cubierta de la canaleta de cables (Figura 3) en la carcasa de la luminaria con los dos tornillos. 9. Remettez le couvercle de la goulotte guide-fils à sa place (Figure 3) sur le boîtier du luminaire à l’aide des deux vis. Nota: Asegúrese de que los cables no queden atrapados entre la carcasa y la cubierta de la canaleta de cables. Remarque : assurez-vous que les fils ne sont pas coincés entre le boîtier et le couvercle 10. Instale el difusor (2).
PAGE 8
CCT/ALO Selection Selección CCT/ALO Sélection de la TCP et du RLR 1. Locate the CCT and ALO Switches (5). Default CCT is set at 4000K and default light output is set at 3000lm. Note: the label for the light output uses different light bulb symbols to indicate each option. 1. Localice los interruptores CCT y ALO (5). El CCT predeterminado se establece en 4000 K y la salida de luz predeterminada se establece en 3000 lm.