Installation Guide

ManualsBrandsLithonia Lighting ManualsOtherWhite Outdoor Fluorescent Cylinder Entry Light

SAVE THESE INSTRUCTIONS

2008 © Acuity Lighting Group, Inc., Rev A 03/17/08

INST SHT CS JELLY JARS_RJ523003

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

INSTALLATION

INSTRUCTIONS

RISK OF FIRE - Lamps are hot. Keep

combustible material away from hot

parts.

TROUBLESHOOTING

CAUTION

If this fixture fails to operate properly, check to

make sure:

• The correct lamp is properly installed.

• The fixture is wired correctly.

• The lamp is not faulty.

• The fixture is grounded correctly.

• The line voltage at the fixture is correct.

Observe lamp manufacturer's recommendations

and restrictions on lamp operations, including but

not limited to ballast type, burning position, and

cycling. Use ANSI rated lamps only.

Maintenance: For optimum performance,

periodically clean reflector and lens with a soft,

damp cloth.

Important: DO NOT use abrasive materials, glass

cleaner or other solvents on lens or paint. Use only

mild, soapy water.

WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH,

INJURY, OR SIGNIFICANT PROPERTY DAMAGE

- For your protection, read and follow these warnings

and instructions carefully before installing or maintaining this fixture. These instructions do not attempt to

cover all installation and maintenance situations. If you do not understand these instructions or additional

information is required, contact Lithonia Lighting or your local Lithonia Lighting distributor.

WARNING: RISK OF ELECTRIC SHOCK - To avoid electric shock, serious injury, or death, be certain that

all electrical power is disconnected from the supply branch circuit conductors before installing or main-

taining this fixture. This product must be installed and maintained in accordance with the applicable instal-

lation codes by a person familiar with the construction and operation of the product and the hazards

involved.

WARNING: RISK OF PERSONAL INJURY - This product may have sharp edges. Wear gloves to

prevent cuts or abrasions when removing from carton, handling, installing and maintaining this product.

Lithonia Lighting assumes no responsibility for claims arising out of improper or careless installation or

handling of this product.

IMPORIMPOR

IMPOR

ANT SAFETY INSTRUCTIONSANT SAFETY INSTRUCTIONS

ANT SAFETY INSTRUCTIONS

RISK OF FIRE - Observe lamp

manufacturer’s warnings, recommenda-

tions and restrictions on lamp operation

and maintenance.

WARNINGWARNING

WARNING

• Do not install a damaged fixture.

• This fixture must be wired in accordance

with the National Electrical Code and

applicable local codes and ordinances.

• Proper grounding is required to ensure

personal safety. Be certain green lead

from the fixture is connected to supply

ground.

• Use code compliant connectors for all

electrical connections.

• ALL work should be done by a qualified

electrician.

• WARNING: NEVER connect or disconnect

any component while power supply is

engaged.

DELIVERY: Upon receipt of fixture and accesso-

ries (packed separately), thoroughly inspect for

any freight damage. All damage should be

reported to the delivery carrier. Do not install

damaged fixtures. Compare the catalog de-

scription listed on the packing slip with the fix-

ture label on the inside of the housing to be sure

you have received the correct merchandise.

IMPORTANT SAFETY

INSTRUCTIONS

WARNINGWARNING

WARNING

Jelly Jars

Prior to Installation

Read carefully before installing light fixtures. If you do not understand these instructions, please

contact your local Lithonia distributor before installing. Make sure your materials and installation

meet local electrical codes and burial depths. Install only on GFCI protected circuit. Use silicone

tape on all threaded parts to seal water out.

RE-LAMPING

Caution: Be sure fixture temperature is cool enough to touch. Prior to installing, check that the lamp is of

proper type and wattage. Observe lamp manufacturer's recommendations on lamp orientation, ballast

type and burning positions.

1. Unscrew globe or cylinder enclosure (Keep for reinstallation.

2. Install appropriate lamps. Do not overtighten. Overtightening will cause stripping and void all

warranties.

3. Reisntall globe or cylinder.

INSTALLATION

Wall Mounting: Wall mounted jelly jar fixtures are mounted using a crossbar and universal nipple

attached to the junction box. Screw the crossbar into the box using the screws included (Figure 1).

Thread nipple onto the crossbar. Wire fixture. Place fixure over nipple and secure it with the acorn nut.

WIRING (Figure 2):

1. Connect black fixture lead to the 120V supply lead.

2. Connect the white fixture lead to the supply common lead.

3. Connect supply ground wire to fixture crossbar ground screw.

Figure 1

Figure 2