Installation Guide

ManualsBrandsLithonia Lighting ManualsWall Pack LightsBronze Integrated LED Wall Pack Light

SAVE THESE INSTRUCTIONS

2003 © Acuity Lighting Group, Inc., Rev C 08/09/07

RJ5210141 INST SHT TWR1

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

INSTALLATION

INSTRUCTIONS

RISK OF FIRE - Lamps are hot. Keep

combustible material away from hot

parts.

TROUBLESHOOTING

CAUTION

If this fixture fails to operate properly, check to

make sure:

• The correct lamp is properly installed.

• The fixture is wired correctly.

• The lamp is not faulty.

• The fixture is grounded correctly.

• The line voltage at the fixture is correct.

Observe lamp manufacturer's recommendations

and restrictions on lamp operations, including but

not limited to ballast type, burning position, and

cycling. Use ANSI rated lamps only.

Maintenance: For optimum performance,

periodically clean reflector and lens with a soft,

damp cloth.

Important: DO NOT use abrasive materials, glass

cleaner or other solvents on lens or paint. Use only

mild, soapy water.

WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH,

INJURY, OR SIGNIFICANT PROPERTY DAMAGE

- For your protection, read and follow these warnings

and instructions carefully before installing or maintaining this fixture. These instructions do not attempt to

cover all installation and maintenance situations. If you do not understand these instructions or additional

information is required, contact Lithonia Lighting or your local Lithonia Lighting distributor.

WARNING: RISK OF ELECTRIC SHOCK - To avoid electric shock, serious injury, or death, be certain that

all electrical power is disconnected from the supply branch circuit conductors before installing or main-

taining this fixture. This product must be installed and maintained in accordance with the applicable instal-

lation codes by a person familiar with the construction and operation of the product and the hazards

involved.

WARNING: RISK OF PERSONAL INJURY - This product may have sharp edges. Wear gloves to

prevent cuts or abrasions when removing from carton, handling, installing and maintaining this product.

Lithonia Lighting assumes no responsibility for claims arising out of improper or careless installation or

handling of this product.

IMPORIMPOR

IMPOR

ANT SAFETY INSTRUCTIONSANT SAFETY INSTRUCTIONS

ANT SAFETY INSTRUCTIONS

RISK OF FIRE - Observe lamp

manufacturer’s warnings, recommenda-

tions and restrictions on lamp operation

and maintenance.

WARNINGWARNING

WARNING

• Do not install a damaged fixture.

• This fixture must be wired in accordance

with the National Electrical Code and

applicable local codes and ordinances.

• Proper grounding is required to ensure

personal safety. Be certain green lead

from the fixture is connected to supply

ground.

• Use code compliant connectors for all

electrical connections.

• ALL work should be done by a qualified

electrician.

• WARNING: NEVER connect or disconnect

any component while power supply is

engaged.

DELIVERY: Upon receipt of fixture and accesso-

ries (packed separately), thoroughly inspect for

any freight damage. All damage should be

reported to the delivery carrier. Do not install

damaged fixtures. Compare the catalog de-

scription listed on the packing slip with the fix-

ture label on the inside of the housing to be sure

you have received the correct merchandise.

Wall Pack

IMPORTANT SAFETY

INSTRUCTIONS

WARNINGWARNING

WARNING

Prior to Installation

Read carefully before installing light fixtures. If you do not understand these instructions, please

contact your local Lithonia distributor before installing.

INSTALLATION

MOUNTING: Wall pack is designed to allow for a variety of mounting configurations. It

can be mounted directly to a recessed junction box or mounted directly to the wall for

wiring via surface conduit from either side or the top. DO NOT AIM UP. NOT FOR

MOUNTING INVERTED OR ON CEILING.

JUNCTION BOX MOUNTING

1. Remove the lamp, reflector, and component cover and keep them in a safe place.

2. Look at the back of the rear housing to locate the pre-cast locators that match most

standard junction-box mounting locations. To remove the knock out for wiring access,

either drill through the knock out or carefully use a hammer and punch.

3. Install the provided self-adhesive gasket to the back of the fixture to cover the junction

box.

4. Align the back housing correctly and mount securely.

5. Use approved connectors to connect fixture leads to supply leads, being careful to

follow the wiring directions below.

6. Replace the component cover and reflector and install the lamp, being careful to follow

the re-lamping directions below.

7. Replace front cover. Make sure that the lens gasket is properly seated around the

perimeter of the cover to insure a weathertight seal.

8. Make sure all wiring access holes are sealed with weatherproof silicone sealant.

NOTE: Fixture must be installed per all applicable national and local codes.

Summary of content (2 pages)

PAGE 1
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION INSTALLATION INSTRUCTIONS IMPOR TANT SAFETY INSTRUCTIONS IMPORT WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH, INJURY, OR SIGNIFICANT PROPERTY DAMAGE - For your protection, read and follow these warnings Wall Pack and instructions carefully before installing or maintaining this fixture. These instructions do not attempt to cover all installation and maintenance situations.
PAGE 2
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION Page 2 Reference product warnings and instructions on Page 1 prior to beginning installation. SURFACE CONDUIT MOUNTING 1. Remove the lamp, reflector, and component cover and keep them in a safe place. 2. Look at the back of the rear housing to locate the pre-cast locators which allow for lag-bolt surface mounting. Using a hammer and punch, prepare the housing by knocking out only the appropriate mounting holes. 3.