Specification Sheet

Wafer LED Gimbal
WF3 ADJ
3" LED Wafer Gimbal
IC/Non-IC
New Construction/Remodel
Specications
Aperture: 2.4 (6.1)
Ceiling opening: 3 (7.6)
Overlap trim: 3.7 (9.4)
Height: 1.3 (3.3)
All dimensions are inches (centimeters)
unless otherwise indicated.
FEATURES & SPECIFICATIONS
INTENDED USE — The 3" Wafer-Thin LED gimbal with remote driver box combines high quality light
output and eciency while eliminating the pot light housing for competitive aordability. This innovate
wafer-slim Type IC design allows easy installation for new construction or remodel from below the
ceiling without the requirement of a pot light housing for insulation. The LED module maintains at least
70% light output for 36,000 hours. These LED Wafer gimbals are intended for closets, attics, hallways,
bathrooms, kitchens, basements, sots, entry ways, porches, garages, stairwells, corridors, nursing/
retirement homes, condos, elevators, apartments, and any other small areas.
CONSTRUCTION — IC rated driver and xture - approved for direct contact with insulation. Aluminum
die cast outer frame. Durable, powder coat paint to prevent rust. Round xture with integral edge-lit
LED's. Plenum rated cable connector to connect from module to remote driver box. Isolated driver
integrated inside steel remote box with four 7/8" knockouts with slots for pryout. Suitable for pulling
wires with the 12 cubic-inch wiring compartment to accommodate up to (8) 14 gauge insulated
conductors, or (6) 12 gauge insulated conductors; making the Wafer LED Downlights much easier to wire
in 2in/2out (plus ground) daisy-chain applications and contractor friendly.
INSTALLATION — Ideal for shallow ceiling plenum; no housing required. Steel spring clip for easy
installation. 3" cut out template is provided to ensure a correct sized hole is cut into ceiling for proper
installation of the trim. Size of hole should not exceed 3 1/8 inches for this product. Suitable for installation
in t-grid and drop ceiling applications. 6" plenum space required for installation of remote driver box.
OPTICS — Polycarbonate lens provides even illumination throughout the space. Utilizes 3500K and
5000K option color temperature LEDs. Lens can be tilt up to 20 degrees and rotate up to 180 degrees.
ELECTRICAL — Connect directly to 120V power supply via provided UL recognized driver. Driver and
Fixture Wet location approved and IC rated. High ecient driver with power factor > 0.9. Ambient
operating temperature: -40°F (-40°C) to +104°F (+40°C). Dimming down to 10% (See page 2 for
recommended dimmers). Standard input wattage is 8W ,68 lumens per watt. Actual wattage may dier
by +/- 5% when operating at 120V +/- 10%. Replaces 50W incandescent.
LISTINGS — CSA certied to US and Canadian safety standards. ENERGY STAR® qualied. Wet location.
Air Tight certied in accordance with ASTM E283-2004. NOM certied.
WARRANTY — 5-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may dier as a result of end-user environment and application.
All values are design or typical values, measured under laboratory conditions at 25 °C.
Specications subject to change without notice.
Notes
1 Total system delivered lumens.
DOWNLIGHTING WF3 ADJ
D
I
M
M
A
B
L
E
WF3 ADJ LED
Series Lamp CCT/W/Lumens
1
CRI Finish
WF3 ADJ 3" LED Wafer Gimbal LED LED 27K 2700K/7.7W/520L
30K 3000K/7.5W/530L
35K 3500K/7.5W/540L
40K 4000K/7.6W/545L
50K 5000K/7.7W/550L
90CRI 90 CRI MW Matte white
MB Matte black
BN Brushed nickel
ORB Oil-rubbed bronze
ORDERING INFORMATION
Example: WF3 ADJ LED 27K MW
Catalog
Number
Notes
Type
PRELIMINARY
[29.2mm]
1.2in
[32.2mm]
1.3in
[76.4mm]
3.0in
[95mm]
Ø 3.7in
[60.7mm]
2.4in
A
A
20°
Accessories: Order as separate catalog number.
WF3 PAN R12 3" new construction pan, retail pack of 12
WF8643 PAN Wafer Universal Pan
WFEXC6 U 6' FT4 cable
WFEXC10 U 10' FT4 cable
WFEXC20 U 20' FT4 cable
WF3_Pan
Matte black Brushed nickel Oil-rubbed bronze
Extension Cable
WF8643 PAN