Specification Sheet

Wafer
TM
LED Recessed Downlight
WF4 MVOLT
4" LED Module
IC/Non-IC
New Construction/Remodel
Specifications
Aperture: 3.2 (8.1)
Ceiling opening: 4.2 (10.7)
Overlap trim: 4.7 (12.0)
Height: 1.1 (2.8)
All dimensions are inches (centimeters) unless otherwise indicated.
FEATURES & SPECIFICATIONS
INTENDED USE — The 4" Wafer
TM
LED recessed downlight with remote driver box combines high quality
light output and efficiency while eliminating the pot light housing for competitive affordability. This
innovative wafer-slim Type IC design allows easy installation for new construction or remodel from
below the ceiling without the requirement of a pot light housing. The LED module maintains at least 70%
light output for 35,000 hours. These Wafer
TM
LED downlights are intended for closets, attics, hallways,
bathrooms, kitchens, basements, soffits, entry ways, porches, garages, stairwells, corridors, nursing/
retirement homes, condos, elevators, apartments, and any other small areas.
CONSTRUCTION — IC rated driver and fixture - approved for direct contact with insulation. Aluminum die
cast outer frame. Durable, powder coat paint to prevent rust. Round fixture with integral edge-lit LED's.
Plenum rated cable connector to connect from module to remote driver box. Isolated driver integrated inside
steel remote box with four 7/8" knockouts with slots for pryout. Not suitable for pulling wires.
INSTALLATION — Ideal for shallow ceiling plenum; no housing required. Steel spring clip for easy
installation. 4" cut out template is provided to ensure a correct sized hole is cut into ceiling for proper
installation of the trim. Size of hole should not exceed 4 1/4 inches for this product. Suitable for installation
in t-grid and drop ceiling applications.
OPTICS — Edge-lit LED technology uses light guided plate to distribute light. Polycarbonate lens
provides even illumination throughout the space. Utilized 2700K, 3000K, 3500K, 4000K, and 5000K color
temperature LEDs.
ELECTRICAL — Multi-volt (120-277V, 50/60Hz) proprietary remote LED driver/splice box, with two
(2) additional low-voltage wires for 0-10v dimming, down to 10% (depending on dimmer model and
application). High efficient driver with power factor > 0.9. Ambient operating temperature: -40°F (-40°C)
to +104°F (+40°C). Standard input wattage is 9.6W, 70 lumens per watt.
LISTINGS — CSA Certified to Canadian and US safety standards. ENERGY STAR® certified. Certified to the
high efficacy requirements of California T24. Wet location. Air Tight certified in accordance with ASTM
E283-2004.
WARRANTY — 5-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
All values are design or typical values, measured under laboratory conditions at 25 °C.
Specifications subject to change without notice.
DOWNLIGHTING WF4 MVOLT
Catalog
Number
Notes
Type
3.2"
(8.1)
4"
(10.2)
4.7"
(12.0)
1.1"
(2.8)
Accessories: Order as separate catalog number.
WF4 PAN R12 4" new construction pan, retail pack of 12
WFJB U Remodel joist bar
WFEXC6 U 6' FT4 cable
WFEXC10 U 10' FT4 cable
WFEXC20 U 20' FT4 cable
Matte black Brushed nickel Oil-rubbed bronze
Notes
1 Total system
delivered lumens.
2 2 Only stocked in
Matte White finish,
enter non-stock
order for other color
finishes there is a 45
day lead time.
WF4_Pan
Joist Extension Cable
3.0 (7.7 cm)
1.3
(3.3 cm)
5.5 (14.0 cm)
WF4
Series Lamp CCT/CRI/W/Lumens
1
Voltage Finish
2
WF4 4" Wafer
TM
LED downlight LED LED 27K 2700K/80CRI/10.6W/660L
30K 3000K/80CRI/9.6W/675L
35K 3500K/80CRI/10.2W/740L
40K 4000K/80CRI/10W/765L
50K 5000K/80CRI/10.4W/780L
MVOLT Multi-Volt
(120-277V)
MW Matte white
MB Matte black
BN Brushed nickel
ORB Oil-rubbed bronze
ORDERING INFORMATION
For shortest lead times, configure product using standard options (shown in bold).
Example: WF4 LED 30K MVOLT MW