Cut Sheet

Wafer LED Recessed Downlight
WF6
6" LED Module
IC/Non-IC
New Construction/Remodel
Specifications
Aperture: 4.9 (12.4)
Ceiling opening: 6 (15.2)
Overlap trim: 6.7 (17)
Height: 1.1 (2.8)
All dimensions are inches (centimeters) unless otherwise indicated.
FEATURES & SPECIFICATIONS
INTENDED USE — The 6" Wafer-Thin LED recessed downlight with remote driver box combines high
quality light output and efficiency while eliminating the pot light housing for competitive affordability. This
innovative wafer-slim Type IC design allows easy installation for new construction or remodel from below
the ceiling without the requirement of a pot light housing. The LED module maintains at least 70% light
output for 36,000 hours. These LED Wafer downlights are intended for closets, attics, hallways, bathrooms,
kitchens, basements, soffits, entry ways, porches, garages, stairwells, corridors, nursing/retirement homes,
condos, elevators, apartments, and any other small areas.
CONSTRUCTION — Ideal for shallow ceiling plenum since a pot light housing is NOT required. IC rated
driver and fixture - approved for direct contact with insulation. Aluminum die cast outer frame. Durable,
powder coat paint to prevent rust. Round fixture with integral edge-lit LED's. Steel spring clip for easy
installation. Plenum rated cable connector to connect from module to remote driver box. Isolated driver
integrated inside steel remote box with four 7/8" knockouts with slots for pryout. Suitable for pulling wires
with the 12 cubic-inch wiring compartment to accommodate up to (8) 14 gauge insulated conductors, or
(6) 12 gauge insulated conductors; making the Wafer LED Downlights much easier to wire in 2in/2out (plus
ground) daisy-chain applications and contractor friendly.
PATENT PENDING.
INSTALLATION — Ideal for shallow ceiling plenum; no housing required. Steel spring clip for easy
installation. 6" cut out template is provided to ensure a correct sized hole is cut into ceiling for proper
installation of the trim. Size of hole should not exceed 6 1/4 inches for this product. Suitable for installation
in t-grid and drop ceiling applications. 2" plenum space required for installation of the remote driver box.
OPTICS — Wafer-Thin downlight edge-lit LED technology uses light guided plate to distribute light.
Polycarbonate lens provides even illumination throughout the space. Utilized 2700K, 3000K, 3500K, 4000K,
and 5000K color temperature LEDs.
ELECTRICAL — Connect directly to 120V power supply via provided UL recognized driver. High efficient
driver with power factor > 0.9. Ambient operating temperature: -40°F (-40°C) to +104°F (+4C). Dimming
down to 10% (See page 2 for recommended dimmers). Standard input wattage is 13W, 79 lumens per watt.
Replaces 75W incandescent for 865 lumens and 100W incandescent for 1020 lumens.
LISTINGS — CSA certified to US and Canadian safety standards. ENERGY STAR® certified product. Wet
location. Air Tight certified in accordance with ASTM E283-2004. NOM Certified.
WARRANTY — 5-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
All values are design or typical values, measured under laboratory conditions at 25 °C.
Specifications subject to change without notice.
DOWNLIGHTING WF6
D
I
M
M
A
B
L
E
Catalog
Number
Notes
Type
4.9"
(12.4)
5.9"
(12.4)
6.7"
(17.0)
1.1"
(2.8)
Matte black Brushed nickel Oil-rubbed bronze
1036859 / LIT WF6-LED-30K-MW-M6 WAFER LED
REXEL LIGHTING MAGAZINE 2.0
6/7/2018 Acuity Brands

Summary of content (7 pages)