TRS-20 TURF RAKE (Serial No. 00127 & UP) TSS-20 TURF SEEDER (Serial No. 00143 & UP) OPERATORS / PARTS MANUAL Schiller-Pfeiffer, Inc.
TABLE OF CONTENTS INTRODUCTION ......................................2 GENERAL MAINTENANCE ......................8 Thank You ............................................................2 Read This Manual ................................................2 Warranty................................................................2 Measurements ......................................................2 Serial Numbers......................................................2 Ordering Parts ............................
PRE-DELIVERY CHECK LIST CHECK THE FOLLOWING BEFORE YOU DELIVER THE TRS-20/TSS-20 TO THE CUSTOMER. 1. Guards and shields fastened in place. 2. Decals fastened and legible. 3. Gas lever on engine turned on. 4. All lubrication points greased. 5. Air cleaner. 6. Touch up scratches. 7. Add engine oil (refer to Engine manual) 8. Add fuel, start engine, test run. DATE SET UP __________/__________/__________ DELIVERY CHECK LIST REVIEW THE OPERATORS MANUAL WITH THE CUSTOMER. 1. Classen Mfg., Inc. warranty. 2.
SAFETY PRECAUTIONS TRAINING 1. 2. 3. 4. 5. 6. Regard the unit as a piece of power equipment and teach this regard to all who operate this unit. Read the instructions carefully. Be familiar with the controls and the proper use of the equipment. Never allow children, teenagers or people unfamiliar with these instructions to use this piece of equipment. Avoid operating unit while people, especially children or pets, are nearby.
14. Stop the engine and disconnect the spark plug wire: a) before checking, cleaning or working on unit b) after striking a foreign object (inspect the unit for damage and make repairs before restarting and operating) 15. Stop the engine: a) whenever you leave the unit b) before refueling c) before clearing blockages. 16. Reduce the throttle setting during engine run-out and, if the engine is provided with shut-off valve, turn the fuel off at the conclusion of operating. 17.
OPTIONAL BLADE ASSEMBLIES CHANGING BLADE ASSEMBLIES Within minutes your machine can be converted to a turf rake, turf seeder or turf slicer by purchasing the optional blade assemblies available complete with side plates, bearings and drive pulley. Changing the blade assembly can be done quickly as described below. REPLACING SHAFT ASSEMBLY ONLY If replacing the existing shaft assembly, only follow steps 1 through 3 above. Proceed with the following steps. 1.
Seeding/Multipurpose Height The seeding/multipurpose blades are used for cutting grooves for over-seeding and can also be used for verticutting grasses. To set the height properly place unit on the lawn surface and adjust the wheel height up (see Fig. 4 ). Adjusting the wheel height up lowers the blades. Seeding The proper height setting for over-seeding is approximately 1/4” into the ground. Adjust the wheel height up approximately one notch. If set deeper, grass seed being applied may not germinate.
GENERAL MAINTENANCE TO KEEP THE TRS-20/TSS-20 IN GOOD OPERATING CONDITION, PERFORM THE FOLLOWING: • • • • • • • • When replacement parts are required, use genuine Classen parts or parts with equivalent characteristics including type, strength, and material. Failure to do so may result in product malfunction and possible injury to the operator and/or bystanders. Keep all safety decals legible. Remove all grease, dirt and debris from decals.
CARE FOR HYDRAULIC SYSTEM To keep the hydraulic system in working order, there are a few steps needed to take place. If synthetic oil were used we would suggest a full synthetic oil such as Mobil 1 15W50, Quaker State Full Synthetic 5W50, or a similar oil. Oil viscosity is very important to transmission life. For optimum performance the oil viscosity should maintain a viscosity of 13 cSt [70 SUS]. The minimum oil viscosity to prevent component wear is 9 cSt [55 SUS].
PARTS MAIN FRAME ASSEMBLY 10
PARTS SELF PROPELLED ASSEMBLY 11
PARTS HANDLE ASSEMBLY 12
SEEDER/MULTIPURPOSE BLADE ASSEMBLY KEY 1 2 3 4 5 6 QTY/PER PART NO. MACHINE 700025 1 100310 26 500216 52 500217 52 600030 1 900026 1 DESCRIPTION Shaft w/ Blade Holders, Multipurpose Blade w/ 15/16” Holes, Multipurpose Bolt, 5/16-18 x 314 Grade 8 Nut, 5/16-18 Tap Lock Shaft/Blades Sub-Assembly, Multipurpose Complete Multipurpose Shaft Assembly (Includes Shaft, Blades, End Plates, Bearings, Pulley, Key & Fasteners) - Not Shown SLICER BLADE ASSEMBLY (OPTIONAL) KEY 1 2 3 4 5 6 QTY/PER PART NO.
TSS-20 SEED BOX ASSEMBLY KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 14 QTY/PER PART NO.
SEEDER TIRE SCRAPE INSTALLATION SEED BOX INSTALLATION For shipping purposes only, the seed box assembly is attached to machine improperly. To set your machine correctly for operation, remove hairpin clip (A) from upper connecting rod (B). Slide upper rod out, allowing “A shaped” stabilizing bracket (C) on seed box to sit over lower connecting rod. (When mounted properly, wheels of seed box should be resting on front wheels of machine.) Reinsert rod and clip.
SAFETY DECALS QTY/PER KEY PART NO. MACHINE DESCRIPTION 1 100074 2 Decal, “Classen” 2 100060 1 Decal, “CAUTION - Muffler and Shields May Exceed 150°” 3 100340 1 Decal, “TRS-20” (Turf Rake only) 4 100071 1 Decal, “Bail Engagement” 5 100061 1 Decal, “CAUTION - Operating Instructions” 16 KEY 6 7 8 9 10 11 QTY/PER PART NO.
NOTES 17
Schiller-Pfeiffer, Inc. 1028 Street Road • Southampton, PA 18966 Telephone: 1-800-366-6268 ONE YEAR LIMITED WARRANTY Effective January 1, 1994 For the period of one year from the date of purchase, CLASSEN MFG., INC. will repair or replace for the original purchaser (90 days if used for rental purposes) free of charge, any part or parts found upon the examination of our factory authorized service station, or by the factory in Norfolk, Nebraska, to be defective in material or workmanship.
