Smart Helmet EVO21 Quick Start Guide & Warranty Information www.livall.
I.Introduction Welcome to the User Guide for LIVALL smart helmets. This Guide will help you better use this product. With continuous improvements of our products, this Guide will be updated from time to time. You can access the latest version and learn more about the helmet on www.livall.com. Back Front Taillight Front Lights Chinstrap Tension adjuster Power Switch Note: The picture is for reference only. If the actual product appears different from the picture, the real product shall prevail. II.
III.
IV. Operation Instructions Turn On Your Helmet For the first time to use, press the power on button located at the back of the helmet, once the tail lights illuminate the smart helmet is on. Note: If it cannot be activated successfully, please charge it and try again. Hold the button Battery Status Remaining battery level is shown by the number of light beads in the middle of the tail, that is displayed when a helmet is initially turned on. Full battery is indicated when all of the light beads are on.
2) Replacing device (When the original BR80 lost or damaged) Put the power-on BR80 close to the main control of the helmet, and the warning light flashes three times per second, indicating that there is a BR80 that needs to be connected to the helmet. Press the power button of the helmet within 10s to confirm the connection of the BR80. Then the tail light of the helmet will continue to flash in the light mode before connection.
Adaptive lighting(The feature is enabled by default and can be closed by the app.) When the helmet is powered on during the day or in a bright environment, only the central LED light will keep flashing, other LED lights will turn off automatically. During the night, or in a dark environment, the whole taillight will keep flashing. Lighting Mode After the helmet is turned on, press the power button for a second to switch between the three lighting modes.
Tips: In order to ensure a stable Bluetooth connection whilst riding, use a smartphone holder and place the phone on your handlebars . SOS Alert(need to be connected to LIVALL Riding APP) The helmet has a fall detection sensor which sends a signal to the LIVALL Riding APP via Bluetooth technology when a fall is detected. Then the APP will send an SOS message to a pre-arranged emergency contact.
EVO21 Product Feature List NO Function NO Function 1 Automatic Standby 6 Lighting Mode 2 Automatic Wake Up 7 Turn light 3 Battery Status 8 Brake warning light 4 Adaptive Lighting 9 SOS Alert 5 Front light Kind Reminder: Please refer to the Quick Start Guide for more details about the functions. V.Considerations 1. The helmet contains electronic parts inside. Please do not take a long ride in the rain although the helmet can prevent the rain from splashing. 2.
6. Trying to clean the golden colour contacts of the charging plug sheet with metal or hard tools such as blades or tweezers is strictly forbidden. Please use cotton swabs with clean water or alcohol in case of cleaning. Please make sure the charging plug is clean and try while charging the helmet. 7. The built-in battery is forbidden to be disassembled, squeezed, heated or burned. It is also forbidden to use screwdrivers and other sharp devices breaking down or prying apart the battery.
VII. Electronic functions troubleshooting During the usage, if the following troubles occur, please charge the product according to quick guide of the model(the helmet can be reset during the charging). If the problems still can not be solved, please contact the aftersales service center. (After-sales email: riding@livall.com) Faults: 1. Can not be charged or turn-off normally; 2. The helmet is turn on, but the lights and other functions can not work normally. 3.
accessories in a way not recommended by the manufacturer. 7. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 8. Take good care of the product, do not wash the surface of the helmet with corrosive solvent, do not strike the helmet; 9.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
一 . 简介 欢迎使用 LIVALL 智能头盔,本指南会指引您如何更好地使用本产品。随着本公司产品的持续完善,本指南 将会不定期更新,您可以在 LIVALL 官方网站(www.livall.
三 .
四 .
2、连接新闪控:(原闪控丢失或损坏后,需要连接新闪控时) 将开机的闪控靠近主控,预警灯 出现 3 次 /S 的闪烁,表示有闪 控需要接入头盔。 10s 内按头盔的电源键,确认连 接该闪控。 此时头盔尾灯继续按之前设置 的灯光模式闪烁,连接成功后, 即可控制左右转向灯。 注:A、闪控连接成功后,可通过操作闪控左(L)、右(R)按键控制头盔左右转向灯; B、除去闪控左(L)、右(R)按键外、中间红色确认按键外,其他键暂时不需使用。 自动休眠 头盔开机后,静止一会儿无晃动,即可进入自动休眠(省电)模式,尾灯熄灭表示休眠成功。 自动唤醒 佩戴前轻轻摇晃几下,即可自动唤醒头盔,尾灯亮起表示唤醒成功。 自适应预警灯光(默认开启,可通过 APP 关闭) 即在光线良好情况下,只有中间的一颗尾灯不停闪烁,其余的尾灯将自动关闭。在夜间或昏暗环境下,整排 尾灯将自动开启,进入闪烁状态。 15
多种灯光模式 可通过短按尾部电源键切循环切换尾部警示灯 3 种闪烁模式。 刹车警示灯 当头盔检测到明显减速时,尾灯将会全部亮起并停留几秒,以警示后方车辆。 注:头盔晃动过大时,内置传感器也会检测到明显减速,可能会触发警示灯常亮,属于正常现象。 连接手机 Helmetphone 1、 下 载“ 来 啊” 骑 行 APP; 2、打开手机蓝牙,将头盔靠近手 机; 温馨提示:为保障连接信号的稳定性,请尽量将手机放在身体前方。 3、在 APP 中点击“装备”,点击“头盔”, 头盔即可与手机连接,连接成功后“头 盔”显示“EVO21”。 16
摔倒求救(需连接“来啊骑行”APP) 头盔内含摔倒检测传感器,当检测到摔倒时,可将摔倒信号通过蓝牙技术发送到“来啊骑行”APP,由“来 啊骑行”APP 发出求救信息给事先设置好的紧急联系人。 关机 长按尾部电源键即可强制关机头盔, 尾灯熄灭关机成功。 “ 充电 ”电源键 掀开带有“ ”字符的软胶,可见充电接口。使用磁吸 USB 充电口连接头盔充电口,中间区域尾灯亮起表 示正在充电,熄灭表示充电完成。 掀开软胶 17
序号 1 2 3 4 5 功能 自动休眠 自动唤醒 开机电量显示 光感警示灯 前警示灯 EVO21 功能列表 序号 6 7 8 9 功能 多灯光模式 左右转向灯 刹车警示灯 SOS 功能 注:具体功能描述详见快速指南对应内容。 五、注意事项 1、头盔内含电子功能,有短时间防淋溅雨水的功能,请不要长期在下雨环境骑行; 2、头盔淋雨后,尾部警示灯罩内可能会出现水珠,请将头盔放在通风环境下 1-2 天,水珠会自动消除; 3、头盔内含电池,电池的容量会随温度变化而改变,在低温或低于 0 摄氏度环境使用时,产品的续航时间 可能会不同程度衰减; 4、如果出现电子功能无法使用或异常,请充电 3 小时后再继续尝试; 5、 头盔内含撞击检测装置,只有提前连接到“来啊骑行”App 并且开启骑行,头盔受到严重撞击后,您 在“来啊骑行”App 中设置的“紧急联系人”才会收到求救信息; 6、禁止用金属或坚硬工具清洁充电接口金色触点,如刀片、镊子等。如果需清洁请用棉签加清水或酒精擦拭。 18
充电时,请保持充电口清洁,干燥; 7、产品内置的电池,严禁拆卸、挤压、加热或燃烧电池,严禁使用尖锐物、螺丝刀等刺破、撬电池,以上 操作可能会引起电池起火或燃烧; 8、请不要将头盔与尖锐物品一起放置,以免损坏头盔。 注:1、可能因网络异常等问题导致无法成功发送或接收 SOS 信息; 2、为了维持电池的使用寿命,建议头盔每次长期(半年到一年)储存前需充满电。 六、技术规格 充电接口:磁吸式充电口 电气参数:DC 5V/1A 防水等级:IPX5 续航时间:默认灯光模式 10 小时 电池:3.
七、电子功能故障排除 在使用过程中,如果出现以下功能异常,请按各型号快速指南的充电时长进行充电操作(充电时可对头盔进 行复位)。如果还是无法排除,请联系售后服务中心。(售后邮箱:riding@livall.
21
22
Designed and Manufactured in Shenzhen, China Approved body: ITS Testing Services(UK) Ltd., Centre Court, Meridian Business Park, Leicester LE19 1WD. UKCA AB0362 Notified Body: Telefication B.V. with its office located at Wilmersdorf 50, 7327 AC Apeldoorn, The Netherlands. Notified Body No. 0560 Original Design Manufacturer: LIVALL Tech Co., Ltd. Address: 904, R&D Building Tsinghua Hi-Tech Park, NanShan, Shenzhen, China Postal Code: 518057 Website: www.livall.