Installation Manual

ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
4213 4215 4219 4223 4225 4228
 WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
 ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.2)
1. Return the arms to suitable position, see figure.2.
2. Attach the loop(I) to the top pipe thread of the fixture body (L), by turning it clockwise
until tighten.
3. Raise the pipe thread(N) into the bottom plate of the fixture body(L) and lock it
securely with finial(M), attach the cover (O) to end of the pipe thread, lock it securely
with finial (P).
4. Attach the glass(K) onto the lamp holder, then lock it securely with check ring (J).
5. Install the light bulbs(Not included) in accordance with the fixture specifications.
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
HANGING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker and remove old fixture from ceiling, including
the old single bar. Shut off the power at the circuit breaker and remove old fixture from
ceiling, including the old single bar.
2. Carefully unpack new fixture and lay all the parts on a clear surface.
3. Thread nipple (C) into loop (F) until snug.
4. Thread other end of nipple (C) with loop attached into single bar (D) until snug.
5. Place lock washer (B) over end of nipple protruding through single bar and thread hex
nut (A) onto nipple until tight.
6. Take this single bar assembly and mount to ceiling junction box with junction box
screws (E). Tighten screws securely with screwdriver.
7. Using proper chain pliers to open one end link of the chain provided and connect to the
fixture loop. Close the link.
8. By measuring, determine correct number of links needed for proper hanging height.
Using proper chain pliers disconnect and discard remaining chain.
9. Lace the fixture wires through the chain.
10. Slip loop collar (H) over the chain, then do the same with the canopy (G).
11. Open the other end link of the chain and hang the fixture on the loop at the ceiling .
Close the link.
12. Feed the fixture wires through the loop (F) and nipple (C) and pull until taut.
CONNECTING THE WIRES (Fig.3)
1. Take the black wire from the ceiling junction box and the smooth wire leg from the
fixture and twist bare ends together. Twist wire connector onto end of wire until snug.
2. Repeat same process with white junction box wire and ribbed wire leg of fixture wire.
NOTE: Twist wires together in the same direction you twist the wire connector onto
wires.
3. If your junction box has a grounding wire (green or bare copper), attach this wire and
the bare copper wire from the fixture together as step 1.If junction box has no ground
wire, attach the bare copper fixture wire to the green ground screw on the crossbar.
4. Tuck these wire connections neatly into the ceiling outlet box and then raise the
canopy (G) all the way to the ceiling. Raise the loop (H) and thread onto ceiling loop
protruding through canopy.
Your installation is now complete. Return power to the junction box and test
the fixture.
I
L
M
N
O
P
WHITE
HOUSE
Black
WIRES
(
Hot
)
FIXTURE
WIRES
BLACK
WIRES
FIXTURE
Bare
FIXTURE
WIRES
(Ground)
HOUSE
(
Neutral
)
WIRES
White
Green or
WIRES
HOUSE
Copper(Ground)
GREEN
Thread
Thank you for purchasing a LIVEX product.
Need assistance with parts or assembly? Please call customer service at: 800-761-8056
Or visit us on-line at: WWW.LIVEXLIGHTING.COM
©COYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING,INC. DOC20160204213
FIG.3
FIG.1
FIG.2