Installation Guide

ManualsBrandsLivex Lighting ManualsChandeliers3-Light Antique Brass Chandelier

ASSEMBLING

ASSEMBLING &

& INSTALLATION

INSTALLATION

INSTALLATION INSTRUCTIONS

INSTRUCTIONS

INSTRUCTIONS PRODUCT#

PRODUCT#

PRODUCT# 500

500

500 9

9 50

50 10

10 50

F or

or Chain

Chain

Chain Hang

Hang

Hang OR

OR Ceiling

Ceiling

Ceiling Mount

Mount

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .

ASSEMBLING

ASSEMBLING THE

THE

THE FIXTURE

FIXTURE

FIXTURE (

(

( Fig.

Fig.

Fig. 2)

2) .

1. Attach the pipe nipple ( D ) to top center coupling of fixture body ( G ) by

turning it clockwise until tight , then slide the column(C) and cover(B)

over end pipe nipple of the fixture body,lock them whit the hex nut,

attach the loop(A) to the end pipe nipple by turning it clockwise

until tight.

2. Slide the cover( F ) onto the lamp holder ,slide the candle sleeve( E )

over the lamp holder.

3. Install the light bulbs in accordance with the fixture specifications

NOTE:

NOTE: DO

DO NOT

NOT

NOT EXCEED

EXCEED

EXCEED THE

THE

THE SPECIFIED

SPECIFIED

SPECIFIED WATTAGE!

WATTAGE!

HANGING

HANGING THE

THE

THE FIXTURE

FIXTURE

FIXTURE (

(

( Fig.

Fig.

Fig. 1)

1. Shut off the power at the circuit breaker and remove old fixture from

ceiling, including the old mounting plate .

2. Carefully unpack new fixture and lay all the parts on a clear surface.

3. Thread the two Studs (A) about 1/4 ” into the pre-drilled holes in the

mounting plate spaced the same distance apart as the holes in the

fixture canopy . Install the mounting plate to the Junction Box with the

two Junction Box Screws as shown. The side of the mounting strap

marked " GND " must face out.

4. Us ing proper chain pliers to open one end link of the chain provided

and connect to the fixture loop. Close the link .

5. By measuring, determine correct number of links needed for proper

hanging height. Using proper chain pliers disconnect and discard

remaining chain.

6. Lace the fixture wires through the chain.

7. Open the other end link of the chain and hang the f ixture on the loop

at the ceiling. Close the link.

8. Feed the fixture wires through the loop of the canopy and pull until

taut.

9. Slide canopy up flush to ceiling, lock it securely with the ball nut s .

**If

**If you

you

you not

not

not need

need

need assembly

assembly

assembly the

the

the fixture

fixture

fixture loop

loop

loop ,

, please

please

please pause

pause

and

and refer

refer

refer to

to Fig

Fig

Fig 4.**

4.**

1. Take

Take

Take out

out

out the

the

the bottom

bottom

bottom loop

loop

loop of

of the

the

the canopy

canopy

canopy and

and

and take

take

take the

the

the loop(A)

loop(A)

loop(A) ,

then

then take

take

take the

the

the canopy

canopy

canopy to

to the

the

the fixture

fixture

fixture body,

body,

body, lock

lock

lock it

it with

with

with the

the

the shim

shim

and

and hex

hex

hex nut

nut

nut until

until

until tight.

tight.

2. Attach

Attach

Attach the

the

the fixture

fixture

fixture body

body

body to

to the

the

the ceiling,

ceiling,

ceiling, lock

lock

lock it

it securely

securely

securely with

with

with the

the

ball

ball nut.

nut.

CONNECTING

CONNECTING THE

THE

THE WIRES

WIRES

WIRES (

(

( Fig.

Fig.

Fig. 3)

1. Take the black wire from the ceiling junction box and the smooth

wire leg from the fixture and twist bare ends together. Twist wire

connector onto end of wire until snug.

2. Repeat same process with white junction box wire and ribbed wire

leg of fixture wire. NOTE: Twist wires together in the same

direction you twist the wire connector onto wires.

3. If your junction box has a grounding wire (green or bare copper),

attach this wire and the bare copper wire from the fixture together

as step 1.If junction box has no ground wire, attach the bare copper

fixture wire to the green ground screw on the single bar.

4. Tuck these wire connections nea t ly into the ceiling outlet box and

then raise the canopy (G) all the way to the ceiling. Raise the loop

(H) and thread onto ceiling loop protruding through canopy

Your

installation

installation is

is now

now

now complete.

complete.

complete. Return

Return

Return power

power

power to

to the

the

the junction

junction

box

box and

and

and test

test

test the

the

the fixture.

fixture.

Fig. 1

Fig. 2

Fig. 4

Hex nut

Lock washer

Fig. 3

White or

HOUSE

Black

WIRES

(Hot)

Smooth

FIXTURE

WIRES

Black or

Ribbed

WIRES

FIXTURE

Bare Copper(Ground)

FIXTURE

WIRES

Copper

(Ground)

HOUSE

(Neutral)

WIRES

White

Bare

Green or

WIRES

HOUSE

Listed