Installation Guide

ASSEMBLING & INSTALLATION INSTRUCTIONS PRODUCT 5022 5023 5025 5026
FOR CHAIN HANG FIXTURE
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
Fig.1
I
H
CHAIN
G
F
E
D
A
B
C
Junction Box
(Not included)
ASSEMBLING THE FIXTURE (Fig.2).
1. Attach the column(A) to top screw hole of lamp body(C) and tight it
until snug. Plac
e the candle sleeve(D) into the small cup of lamp holder.
2.
Attach the pipe screw into the ball nut until tight, raise the pipe screw(G)
into the bottom hole of the bell glass(E), attach the cover(I)
onto the
bottom of bell glass, lock it securely with the finial(J).
3. Raise th
e bell glass(E) insert the big loop(H), hook the end of arms(B
) to
the colu
mn’s hooked and link(F), fasten the link and hook the big loop’
s
hooked.
4. Install the l
ight bulbs in accordance with the fixture specifications
NOTE: DO NOT EXCEED THE SPECIFIED WATT
AGE!
HANGING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker and remove old fixture from
ceiling, including the old single bar.
2. Carefully unpack new fixture and lay all the parts on a clear su
rface.
3. Thread nipple (C) into loop (F) until snug.
4. Thread other e
nd of nipple (C) with loop attached into singl
e bar (D)
until snug.
5. Place lock
washer (B) over end of nipple protruding through si
ngle bar
and thread hex
nut (A) onto ni
pple until tight.
6. T
ake this single bar assembly and mount to ceiling junction box with
junction box screws (E). Tighten screws securely with screwdriver.
7. Using proper chain pliers to open one end link of the chain provided
and connect to the fixture loop (I). Close the li
nk.
8. By
measuring, determine correct number of links needed for
proper
hanging height. Using proper chain pliers disconnect and discard
re
maining chai
n.
9. Lace the fixture wires through the chain.
10. Slip loop collar
(H) over the chain, then do the same with the canopy
(G).
11. Open the other
end link of the chain and hang the fixture on th
e loop
at the ceiling. Close the link.
12. Feed the fixtur
e wires through the loop (F) and nipple (C) and pull
until taut.
13. Slide canopy (G) up flush to ceiling, secure using loop (H).
CONNECTING THE WIRES (Fig.3)
1. Take the black wire from the ceiling junction box and the smooth wire
leg from the fixture and twist bare ends together. Twist wire connector
onto end of wire until snug.
2.
Repeat same process with white junction box wire and ri
bbed wire leg
of fixture wire.
NOTE: Twist wires together in the same direction you
twist the wire connector onto
wires.
3.
If your junction box has a grounding
wire (green or bare copper),
attach this wire
and the bare copper wire from th
e fixture together as
step 1.If
junction box has no ground wire,
attach the bare copper
fixture wire to t
he green ground screw on the single bar.
4.
Tuck these wire connections neatly into the
ceiling outlet box and then
raise the canop
y (G) all the way to the ceiling
. Raise the loop (H) and
thread onto ceil
ing loop protruding through canopy
.
Your installation is now complete. Return power to the junction box
and test the fixture.
Fig.2
Fig.3
:KLWHRU
+286(
%ODFN
:,5(6
+RW
6PRRWK
),;785(
:,5(6
%ODFNRU
5LEEHG
:,5(6
),;785(
%DUH&RSSHU*URXQG
),;785(
:,5(6
&RSSHU
*URXQG
+286(
1HXWUDO
:,5(6
:KLWH
%DUH
*UHHQRU
:,5(6
+286(
DOC20141205022