User Manual LCH-ROCK-BL 1
From the Manufacturer Please read this user manual carefully before attempting to operate the appliance and keep it in a safe place for future reference. This appliance and its packaging are produced by processes that minimize waste and respect the environment. Please help us to continue this effort to protect the environment by using the appliance efficiently and dispose of the packaging in a responsible manner. FOR THE USER 1.
Cleaning, Maintenance & Service It is very important to clean and maintain the grease filters regularly (at least once monthly) to improve its efficiency in eliminating heat and contaminated air in the kitchen. Heavy oil deposits is a fire hazard. Hood surface should be cleaned with soft cloth and non-corrosive detergent. Important: Never attempt to repair this appliance by yourself. Always refer to qualified Service Technicians. For safety precaution, always purchase the original replacement parts.
3. Dimension Diagrams 3) T Shape Range Hood Instructions for use H. Touch Control (LCH-ROCK-90BL) A B C D E F G Wave A, Within 10-15cm distance from the switch, wave once from left to right to turn on power, wave to the right, the fan runs at mid speed. Wave to the right again, the fan runs at high speed." “Repeat this cycle". Press B, turn on the light. Press it again, turn off the light. Press C, the fan runs at high speed. Press again, the fan turns off. Press D, the fan runs at mid speed.
Cleaning & Maintenance ALWAYS SWITCH OFF AND UNPLUG FIRST! SURFACES: Wash with warm soapy water and a soft sponge. Never use abrasive detergent, scouring pads, steel wool or solvents on any part of this appliance as this will cause irreparable damage. ALUMNIUM GREASE FILTERS: Wash in the dishwashers or soak the panels in a degreasing agent for an hour, then rinse off and dry before reinstalling.
5. Installation 1. 2. 3. 4. 5. 6. 7. Use suitable bolts to mount the appliance on a secure surface. The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood. When the range hood is located above a gas appliance, this distance shall be at least 65 cm. If the instructions for installation for the gas hob specify a greater distance, this has to be taken into consideration.
Slim model Step 1: 1. To install onto the wall drill 2 holes of Ø8mm on a suitable place according with the centre distance of hole in the back of the cooker hood. 2. To insert the nut into the holes. 3. To insert the screws into the nuts and tight. Put the cooker hood onto the tighten screws. 4. To fix the cooker hood with safety screw. The two safety vents are positioned on the back casing, with diameter of 6mm. 5. To put the one-way valve onto the cooker hood. Step 2: 1.
Notes: 1. The extended pipe is an optional accessory, not included. 2. To take off the protection film before installation. 3. There are 2 methods for ventilation, ' horizontal ventilation' and ' vertical ventilation'. Please pay attention to the ventilation method during installation. Vertical ventilation: See Pic A, please use tool to remove the round cover before installing, the air can be vented from top.
Built-in Mounting Installation Step 1 To ensure the cut-out size is correct before installing the range hood. To install the back draft base to the range hood. Step 2 To secure the undermount into cavity using screws. All screws are to be installed from the bottom of the range hood into the cabinet. Step 3 To connect the 6 pin connectors onto the face plate to the range hood before securing the face plate to the cabinet using provided screws. To insert light bulb and filter into the face plate.
Activated carbon filter can be used to trap odors. In order to install the activated carbon filter, the grease filter should be detached first. Press the lock and pull it downward. Plug the activated carbon filter into the unit and turn it in clockwise direction. Repeat the same on the other side. IMPORTANT NOTES: 1. 2. 3. 4. 5. 6. 7. 8. To ensure the activated carbon filter is securely locked. When activated carbon filter is attached, the suction power will be lower.
FOR THE INSTALLER 6. Safety Information 1. Electrical connection must be in accordance with the local standards and laws. 2. To ensure that the electrical supply in compliance with the appliance setting, otherwise, do not connect. 3. To ensure the power supply cord is free from any heat source or sharp objects. 4. The electrical connection of this appliance must be soundly earthed. In the event of electrical short circuit, grounding reduces the risk of electrical shock.
7.
