MODEL: 32001 SERIES OWNERS MANUAL WARNING: Read Tecumseh Engine Owners Manual and Important Rules for Safe Operation before Operating Vehicle WARNING: YOU MUST ADD OIL TO THE ENGINE PRIOR TO USE!!! 20 oz. or 1 ¼ Pints (.6 Liters) OF SAE 30 MOTOR OIL This vehicle is sold for off-road use only. Before operating this vehicle, read all the instructions for safe assembly and operation as well as the instructions governing the engine and other portions of the vehicle.
Read These Important Rules For Safe Operation NOTE: All the items (1-33) below should be read and understood by the Operator and Parent. Failure to follow these instructions could endanger personal safety of the operator. 1. This vehicle is not licensable. IT IS NOT TO BE OPERATED ON ANY PUBLIC ROAD, STREET, SIDEWALK or ALLEY. To do so would be a violation of local law. This vehicle may be operated only on private property and upon areas approved by local law. 2.
7. The tire pressure should be checked prior to each use. The recommended inflation pressure is the maximum tire pressure which is printed on the tires sidewall. Improper tire pressure may cause instability and may prevent proper braking or steering. 8. Modification of this vehicle or removal of any original equipment or safety decals may render the vehicle unsafe or illegal. Never remove any chained guard, or belt clutch guard. These covers are for the riders protection. 9.
18. Each time before using this vehicle, the fuel supply should be checked. The fuel tank should never be filled while the engine is running or while the engine is hot. Do not fill tank in closed area such as a garage, while smoking, or in the vicinity of an open flame. Do not overfill the tank. Always allow at least ¼ inch of space at the top of the tank for expansion. Never top off tank. Replace cap tightly to prevent spillage of fuel and potential fire hazard.
31. Riding your Fun-Kart requires skill acquired through practice over a period of time. Take the time to learn the basic techniques before attempting to ride the vehicle. 32. Ride only on safe and familiar terrain. Avoid loose gravel and rocks. Be careful on wet surfaces and allow for extra braking distance. 33. ALWAYS mount the caution flag provided on the Fun-Kart for safety purposes. This flag could help prevent dangerous situations.
YERF-DOG Fun-Karts by Flexible Flyer LIMITED WARRANTY The Limited Warranty on this vehicle is in two (2) parts: We offer the original purchaser of this product the following warranty: PART 1 ENGINE Tecumseh warrants the engine for (2) years, not Flexible Flyer. See Tecumseh Engine Owners Manual. Engine repair, replacement parts, and warranty claims must be handled through an authorized dealer in your locality. Tecumseh has an extensive authorized sales and service dealer network.
FLEXIBLE FLYER 100 Tubb Avenue West Point, MS 39773 FOR REPLACEMENT PARTS PLEASE CALL: 1-888-389-5522 (U.S.) 1-888-707-1880 (Canada) ASSEMBLY 1. Complete the Fun-Kart registration and warranty confirmation on the back of this owners manual and mail in within 10 days of purchase. The information is required when ordering parts. 2. Steering Wheel - Bolt the steering wheel to the anchor plate with fasteners provided in the parts bag included with the Fun-Kart.
PRE-RIDE INSPECTION WARNING - Perform this pre-ride inspection everyday before riding the vehicle. If not performed, serious damage to the vehicle and personal injury may result. 1. Engine Oil Level Add oil if required. Check for leaks. Tighten filler cap securely. 2. Fuel Level Add fuel if necessary. Do not overfill (no fuel in filler neck). Replace cap tightly. Check for leaks. Do not mix oil with gas. Only refuel when engine is off and cool. 3.
1. Before starting the engine, the operator should be seated in the Fun-Kart. If the rider is not seated in the vehicle, it should be placed against a stationary object and started. 2. Do not start the engine before checking to make sure the throttle assembly is in the idle position. Warning Each time prior to starting the engine, check throttle assembly to ensure that when the throttle pedal (right side) is pushed all the way forward the assembly is working smoothly and returns to idle when released.
1. Drain fuel tank and remove all fuel remaining in the tank by using a suction device or by soaking up the fuel with a clean rag or towel. Remove all fuel remaining in the carburetor by allowing engine to run out of fuel. Do not perform any fuel removal procedure while smoking or near an open flame. Dispose of any rags or towels properly. 2. Lubricate engine cylinder by removing the spark plug and pouring an ounce of lean lubricating oil through the spark plug hole into the cylinder.
SUSPENSION MAINTENANCE The Suspension System on your Fun-Kart is specifically designed and set up for the smoothest possible ride, while maintaining top performance and kart durability. Your Fun-Karts suspension system uses four shock absorbers, two on the front suspension and two on the rear suspension, to comfortably tackle rough terrain. The two front shock absorbers affect the camber or slant of your front tires.
SHOCK ABSORBER ADJUSTMENT SHOCK ADJUSTMENT HOLE 72 SHOCK ABSORBER 1. Locate the SHOCK ABSORBERS (72) at the front and rear of the FUN-KART 5. Turn the SHOCK ADJUSTMENT HOLE counter-clockwise around the SHOCK to decrease shock absorption. 2. The SHOCKS are pre-set for normal conditions at the factory. 6. Turn the SHOCK ADJUSTMENT HOLE clockwise around the SHOCK to increase shock absorption. 3. Locate the SHOCK ADJUSTMENT HOLE at the base of the spring. 7.
SEAT ASSEMBLY INSTRUCTIONS 1. Locate the SEAT FRAME ASSEMBLY, LAP BELT, and SHOULDER BELT. 5. Secure the SEAT FRAME ASSEMBLY using the hardware shown. 2. Align STUDS on the bottom of the SEAT FRAME ASSEMBLY with the SEAT TAB HOLES on the FUN-KART FRAME. 6. Place the SEAT CUSHION on the SEAT FRAME ASSEMBLY. Secure the SEAT CUSHION to the SEAT FRAME ASSEMBLY using using the hardware shown. 3. Slip SHOULDER BELT and LAP BELT connectors under the rear STUDS on the bottom of the SEAT FRAME ASSEMBLY.
BRUSH GUARD ASSEMBLY INSTRUCTIONS 1. Secure the MAIN BRUSH GUARD (21) to the middle tabs on the FUN-KART FRAME, behind the SEAT, using the hardware shown. 5. Join and secure the FRONT BRUSH GUARD (20) to the ends of the REAR BRUSH GUARDS (51) using the hardware shown. 2. Secure the REAR BRUSH GUARD (51) and SAFETY FLAG (34) to the rear tabs on the FRAME using the hardware shown. 6. Mount the end of the SHOULDER BELT to the side of the MAIN BRUSH GUARD (21) using the hardware shown.
FOAM ATTACHMENT DIAGRAM Attach FOAM (87) to the BRUSH GUARDS using CABLE TIES (81) as shown.
SUGGESTED DECAL APPLICATION Apply Decal kit (00918) as shown in the illustrations below. (Note: Decals are self-adhesive and require no glue.) Yerf Dog logo (1) and Paw Prints (4). Yerf Dog logo (2) applied to both sides of front. Yerf Dog logo (2) applied to both sides of rear.
32001 SERIES REPLACEMENT PARTS IDENTIFICATION Item Part No.
MODEL 32001 SERIES
VEHICLE REGISTRATION AND WARRANTY CONFIRMATION IMPORTANT! Please return this information within 10 days of purchase to validate your warranty. Return to: F.F. Acquisition Corp. YERF-DOG Warranty Dept. P.O. Box 1296 West Point, MS 39773 Thank-you for purchasing this fine YERF-DOG product. With proper use, maintenance and service this kart will bring many years of fun and enjoyment.