Model MICROMAX .380 PARTS LIST – INSTRUCTIONS FOR USE – MAINTENANCE SPECIFICATIONS Caliber…………………………. .380 Number of shots…………………7 Length overall…………………...6 1/3 inches. Weight (unloaded)………………22 oz. Height……………………………4 1/3 inches Sights…………………………….Back rear fixing. Stocks……………………………Polymer Finish…………………………….Blue mat, chrome satin, engraved or gold damascened. Ammunition……………………..380 FABRINOR – P.O.
PARTS LIST A 005 Hammer Pin A 006 Hammer Strut A 007 Hammer Strut Pin A 008 Sear A 009 Sear Pin A 010 Disconnector A 014 Safety Lock A 015 Rear Spring A 016 Main Spring Housing A 017 Main Spring Cap A 020 Main Spring Housing Pin A 022 Main Spring Cap Pin A 031 Trigger A 034 Magazine Catch Lock A 035 Magazine Catch Spring A 046 Plunger Tube A 047 Slide Stop Plunger A 048 Safety Lock Plunger A 049 Plunger Spring A 050 Plunger Screw A 053 Grip Screw A 063 Right Grip (USA) A 064 Left Grip (USA) A 076 Right Grip
DISASSEMBLY OF THE LLAMA MODEL MICROMAX .380 The LLAMA pistol is quite easily taken apart. The parts mentioned in the following instructions refer to those described and illustrated in the schematic. Press the magazine catch (B 096) with your left thumb and take out the magazine (B 704). 2.
OPERATION OF THE LLAMA MODEL MICROMAX .380 TO LOAD: depress the magazine catch, which is located immediately behind the trigger. This will unlock the magazine. To fill the magazine, place the cartridges so that the bullet ends are positioned over the leading edge of the follower. Fill the magazine to capacity. Now take the loaded magazine and slide it back into the lodging frame.
SAFETY FEATURES: the LLAMA automatic pistol incorporates several positive safety devices, which, if properly employed, will avoid the danger of accidental firing. These safety devices are described below. SLIDE LOCK SAFETY: The Slide Lock Safety is located on the left of the pistol just below the back of the slide.
Be sure to move the safety fully into position, or it will not be effective. Some guns have a red warning dot beside the safety, which could be completely covered when the safety is on. Do not carry a gun with a cartridge in the chamber without the safety being on. (Double action revolvers and some double action pistols have automatic internal safety mechanisms rather than manual safeties.) MAINTENANCE 1. All moving parts should be coated lightly. 2.
5. If your gun develops a mechanical malfunction while shooting, or emits powder gas, or if a cartridge primer is punctured, or a cartridge case is bulged or ruptured, or if the sound of firing is not quite right. DO NOT CONTINUE SHOOTING! STOP IMMEDIATELY AND UNLOAD THE GUN, and take it and the ammunition to a gunsmith. 6. A loaded cartridge case that becomes jammed in a semi-automatic gun between the slide (or bolt) and the barrel may be removed as follows: Keep the muzzle pointed in a safe direction.
1. Use high-quality, original factory-made ammunition in your gun. Never use ammunition that is wet, dirty, bent, corroded, or otherwise damaged. Never oil or lubricate ammunition, or let excess aerosol lubricants, preservatives, or cleaners come into contact with cartridges: this can cause dangerous malfunction. Be sure your ammunition is the proper caliber for your gun: you will find the proper caliber permanently engraved on the gun. Do not use any other caliber ammunition. 2.
. Do not use too much lubricant on the moving parts of your gun. Do not spray aerosol gun care products where they may come in contact with ammunition, and do not spray them excessively. Lubricants, especially aerosol sprays, can penetrate cartridge primers and cause the ammunition to misfire. Some lubricants can get inside the cartridge cases and prevent the powder from igniting. If only the primer ignites, the bullet may become lodged in the barrel. GUN CARE 1.
Walker Arms Company 499 Dallas Road #820 Selma, Al. 36701 Bolsa Gunsmithing 7404 Bolsa Avenue Westminster, Ca. 92683 Tel: 334-872-6231 Tel: 714-894-9100 Ahlman's 9525 W. 230th Street Morristown, Mn. 55052 Reynerson's 10044 Hooper Rd. Baton Rouge, LA 70818 Tel: 507-685-4243 or 4244 Tel - 225-261-4860 5. With your gun, enclose a letter stating the serial number, caliber, and barrel length of the gun, and what work is needed or what problem you experienced with it.
LLAMA HANDGUNS ARE DISTRIBUTED EXCLUSIVELY IN THE UNITED STATES AND CANADA BY: IMPORT SPORTS Inc. 1750 Brielle Ave Unit B-1 Wanamassa, NJ 07712 (732) 493-0302 IMPORTANT – KEEP THIS MANUAL WITH YOUR FIREARM! MANUAL MUST BE TRANSFERRED WITH CHANGE OF OWNERSHIP.
