Installation & Assembly

ManualsBrandsLNC Home ManualsCeiling Lights1-Light Single Dome Pendant

  Weareheretohelp:support@lnchome.com

www.lnchome.comPage:  ‐1‐/4

ItemNumber:A03262

WARNING(Toreducetheriskoffire,electricshock,orinjurytopersons):

1. Wesuggestinstallationbyalicensedelectrician.

2. Pleasereadtheinstructioncarefullyandsaveitasyoumayneeditatlatertime.

3. Beforeyoustart,NEVERattemptanyworkwithoutshuttingofftheelectricityuntiltheworkisdone.A).

Gotothemainfuse,orcircuitbreaker,boxinyourhome.Placethemainpowerswitchinthe“OFF”

position.B).Placethewallswitchinthe“OFF”position.

4. Mountingsurfaceshouldbeclean,dry,flat,strongenoughand1/4”largerthanthecanopyonallside.

Anygapsbetweenthemountingsurfaceandcanopyexceeding3/16”shouldbecorrectedasrequired.

5. Makesurethattheceilingorwallcanstandtheweightofthelampbeforefixture.

6. Makesurethevoltageyouareusingis120V.Themaximumwattageis60Wperbulb.

7. Keepthelampawayfromacidicandbasicobjectsincaseofdamagingthesurfaceofthelamp.

8. Whenreplacingbulb,youshouldturnofforunplugthelampandyoumustwaituntilitiscoolasbulbs

gethotquickly.

9. Thesafetyinstructionsappearinginthismanualarenotmeanttocoverallpossibleconditionsthatmay

occur. Itmust beunderstoodthatcommonsense,cautionandcaremustbeusedwith anyelectrical

products.



IMAGEFORFINISHEDPRODUCT：



TOOLSREQUIRED(NOTINCLUDED):

Beforedoingassemblyandinstallationpleasepreparetheneededtoolsasbelowpicture

Summary of content (4 pages)

PAGE 1
We are here to help: support@lnchome.com Item Number: A03262 WARNING (To reduce the risk of fire, electric shock, or injury to persons): 1. We suggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at later time. 3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B).
PAGE 2
We are here to help: support@lnchome.com PARTS TYPE & QTY INCLUDING: (A) Mounting plate assembly (1) (B) Green ground screw (1) (E) Canopy (1) (F) Strain relief (2) (G) Knob ball (2) (H) Cord (1) (I) Socket (1) (J) Metal shade (1) (K) Socket ring (1) ACCESSORIES & QTY ENCLOSED: (C) Plastic Wire Connector (3) (D) Mounting screw (2) (L) Allen wrench (1) ASSEMBLY & INSTALLATION INSTRUCTIONS: 1.
PAGE 3
We are here to help: support@lnchome.com 4. Unscrew the ball knobs (G) from canopy (E) then gently remove the mounting plate assembly (A) 5. Adjust the length of the cords to achievethe desired height of the mounted fixture. 1) Use the allen wrench(L) to unscrew the screw in strain relief (F), carefully pull the cord(H) up or down to lengthen or shorten the cord. (H) 2) Once desired height of fixture is achieved, Carefully and gently tighten the screw till snug 6.
PAGE 4
We are here to help: support@lnchome.com CONNECT FIXTURE WIRES TO GROUND WIRES Connect ground wire according to below chart Connect wires according to below chart Twist plastic wire connector(C) until wires are tightly joined together,wrap each connector with approved electrical tape for more secure connection and carefully stuff all wires into the outlet box 9. Remove the knob balls(G) from the mounting plate assembly (A).