Instructions / Assembly

ManualsBrandsLNC ManualsLighting1-Light Black Swing Arms Wall Sconce

  Weareheretohelp:support@lnchome.com

www.lnchome.comPage:  ‐1‐/5

ItemNumber:A02246

WARNING(Toreducetheriskoffire,electricshock,orinjurytopersons):

1. Wesuggestinstallationbyalicensedelectrician.

2. Pleasereadtheinstructioncarefullyandsaveitasyoumayneeditatlatertime.

3. Beforeyoustart,NEVERattemptanyworkwithoutshuttingofftheelectricityuntiltheworkisdone.A).Gotothemain

fuse,orcircuitbreaker,boxinyourhome.Placethemainpowerswitchinthe“OFF”position.B).Placethewallswitch

inthe“OFF”position.

4. Mountingsurfaceshouldbeclean,dry,flat,strongenoughand1/4”largerthanthecanopyonallside.Anygapsbetween

themountingsurfaceandcanopyexceeding3/16”shouldbecorrectedasrequired.

5. Makesurethattheceilingorwallcanstandtheweightofthelampbeforefixture.

6. Makesurethevoltageyouareusingis120V.Themaximumwattageis60Wperbulb.

7. Keepthelampawayfromacidicandbasicobjectsincaseofdamagingthesurfaceofthelamp.

8. Whenreplacingbulb,youshouldturnofforunplugthelampandyoumustwaituntilitiscoolasbulbsgethotquickly.

9. Thesafetyinstructionsappearinginthismanualarenotmeanttocoverallpossibleconditionsthatmayoccur.Itmust

beunderstoodthatcommonsense,cautionandcaremustbeusedwithanyelectricalproducts.



IMAGEFORFINISHEDPRODUCT：



Summary of content (5 pages)

PAGE 1
We are here to help: support@lnchome.com Item Number: A02246 WARNING (To reduce the risk of fire, electric shock, or injury to persons): 1. We suggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at later time. 3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B).
PAGE 2
We are here to help: support@lnchome.com TOOLS REQUIRED (NOT INCLUDED): Before doing assembly and installation please prepare the needed tools as below picture PARTS TYPE & QTY INCLUDING: (A) Mounting plate (1) (B) Green ground screw (1) (E) Back plate (1) (F) Ball nut (2) (G) Stud (3) (H) Joint (3) (I) Arm (2) (J) Socket (1) (L) Decorative ring (1) (M) Socket ring (1) ACCESSORIES & QTY ENCLOSED: (C) Mounting screw (2) (D)Plastic wire connector (3) ASSEMBLY & INSTALLATION INSTRUCTIONS: 1.
PAGE 3
We are here to help: support@lnchome.com 2. 3. Turn off power Make installation 1) Unscrew the knob nuts ( F) from backplate (E) then carefully remove the mounting plate (A) from backplate (E) 2) Carefully and gently pull the wires and fiberglass sleeve from another end of arm(I) ,meanwhile push the socket to get close to the joint. then lay wires in the cave of joint(H).And continue the step till the joints are combined together,then secure with the stud.
PAGE 4
We are here to help: support@lnchome.com 4) Carefully pass the wires from outlet box through the mounting plate(A) ,then attach the mounting plate (A) to outlet box with mounting screws (C) 5) Make wire connections Connect wires as below wires connecting shown.
PAGE 5
We are here to help: support@lnchome.com 7) Install bulb (Not included. Please do not exceed the maximum capacity recommended on the socket.) Adjust the fixture to desired direction through unscrewing the stud(G). Once the desired direction achieved, tighten the stud (G). 4. Check everything is already installed properly, then you could turn on the light.