CPX-I-O Rev B Installation & Operation Manual Models: 502 - 2072 WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. -- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. -- WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building.
Contents HAZARD DEFINITIONS ..................................................... 2 PLEASE READ BEFORE PROCEEDING ......................... 3 SAFETY INFORMATION ................................................... 4 THE COPPER-FIN2 -- HOW IT WORKS ........................ 5-7 RATINGS ........................................................................... 8 1. DETERMINE UNIT LOCATION Location of Unit ..................................................................
Installation & Operation Manual Please read before proceeding Special instructions NOTICE This is a gas appliance and should be installed by a licensed electrician and/or certified gas supplier. Service must be performed by a qualified service installer, service agency or the gas supplier. WARNING If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.
Installation & Operation Manual Please read before proceeding Safety information Owner warning – The information contained in this manual is intended for use by qualified professional installers, service technicians, or gas suppliers. NOTICE Consult and follow all local Building and Fire Regulations and other Safety Codes that apply to this installation. Consult local gas utility company to authorize and inspect all gas and flue connections.
Installation & Operation Manual The Copper-fin2 - How it works... 1. Heat exchanger The heat exchanger allows system water to flow through specially designed tubes for maximum heat transfer. The glass lined headers and copper fined tubing are encased in a jacket that contains the combustion process. 2. Heat exchanger access cover The heat exchanger access cover is a galvanized steel door which allows access for service, maintenance, and removal of the heat exchanger from inside the combustion chamber.
Installation & Operation Manual The Copper-fin2 - How it works...
Installation & Operation Manual The Copper-fin2 - How it works...
Installation & Operation Manual Ratings Specifications Model Number Note: Change “N” to “L” for L.P. gas models. Appliance Water Content Gallons Water Connections Gas Connections Air / Vent Sizes (Note 1) NOTICE CPN0502 1.7 2" 1-1/4" 6" CPN0652 2.0 2" 1-1/4" 8" CPN0752 2.1 2" 1-1/4" 8" CPN0992 2.2 2-1/2" 2" 10" CPN1262 2.6 2-1/2" 2" 12" CPN1442 2.9 2-1/2" 2" 12" CPN1802 3.3 2-1/2" 2" 12"/14" CPN2072 3.
Installation & Operation Manual 1 Determine unit location Location of unit This unit meets the safe lighting performance criteria with the gas manifold and control assembly provided, as specified in the ANSI standards for gas-fired units and ANSI Z21.10.3/ CSA 4.3 - latest edition. 1. Maintain all clearances from combustible construction when locating appliance. See Clearances from Combustible Construction, this page. 2.
Installation & Operation Manual 1 Determine unit location Anytime the inlet temperature drops below 45°F, the control turns on the pump contact. If the inlet temperature is below 37°F, and the unit is in the ON Mode, the first stage will fire. Location Locate indoor pool heaters in a room having a temperature safely above freezing [32°F (0°C)]. A mechanical room operating under a negative draft pressure may experience a down draft in the flue of a pool heater when it is not firing.
Installation & Operation Manual 1 Determine unit location (continued) All dimensions are based on net free area in square inches. Metal louvers or screens reduce the free area of a combustion air opening a minimum of approximately 25%. Check with louver manufacturers for exact net free area of louvers. Where two openings are provided, one must be within 12" (30 cm) of the ceiling and one must be within 12" (30 cm) of the floor of the equipment room.
Installation & Operation Manual 1 Determine unit location Exhaust fans Combustion air filter Any fan or equipment which exhausts air from the mechanical room may deplete the combustion air supply and/or cause a down draft in the venting system. Spillage of flue products from the venting system into an occupied living space can cause a very hazardous condition that must be immediately corrected.
Installation & Operation Manual 2 Venting BEFORE YOU BEGIN Identify your appliance’s vent system: This manual covers venting requirements for CAT I models and CAT IV vent materials. Be sure to correctly identify the type of vent system your appliance requires before proceeding.
Installation & Operation Manual 2 Venting Vent system options: A (Note: Installations shown below are representative, actual installations may vary from those shown.) This option uses a vertical rooftop flue termination with air supplied from the equipment room - see page 16. CONVENTIONAL NEGATIVE DRAFT VENTING D This option uses a powered vent assembly to exhaust the flue products out a sidewall with air supplied by a pipe from the sidewall - see page 25.
Installation & Operation Manual 2 Venting (continued) General information You must supply adequate combustion and ventilation air to this unit. You must provide minimum clearances for the vent terminal from adjacent buildings, windows that open, and building openings. Follow all requirements set forth in the latest edition of the National Fuel Gas Code, ANSI Z223.
Installation & Operation Manual 2 Venting A Conventional negative draft venting - see page 14. NOTICE Before installing a venting system, follow requirements found in the General Venting section. This option uses Type-B double-wall flue outlet piping. The blower brings in combustion air. The buoyancy of the heated flue products cause them to rise up through the flue pipe. The flue outlet terminates at the rooftop.
Installation & Operation Manual 2 Venting (continued) 4. Turn on clothes dryers and any other appliances not connected to the common venting system. Turn on any exhaust fans, such as range hoods and bathroom exhausts, so they will operate at maximum speed. Do not operate a summer exhaust fan. 5. Close fireplace dampers. 6. Place in operation the unit being inspected. Follow the lighting instructions. Adjust thermostat so unit will operate continuously. 7.
Installation & Operation Manual 2 Venting Figure 2-1_Vent Termination from Peaked Roof - 10 ft. or Less From Ridge NOTICE Vent terminations are not shown in FIG.’s 2-1 thru 2-4. Make sure all vertical vents are installed with vent terminations recommended by the vent manufacturer. Figure 2-3_Vent Termination from Flat Roof - 10 ft. or Less From Parapet Wall 18 Figure 2-2_Vent Termination from Peaked Roof - 10 ft. or More From Ridge Figure 2-4_Vent Termination from Flat Roof - 10 ft.
Installation & Operation Manual 2 Venting (continued) Vertical DirectAire™ venting - see page 14. B NOTICE Before installing a venting system, follow requirements found in the General Venting section. The Vertical DirectAire™ vent system is the same as the Conventional Negative Draft vent system, except it pulls combustion air from the outdoors through a separate air inlet pipe. Follow all requirements in the Conventional Negative Draft Venting section on page 16.
Installation & Operation Manual 2 Venting To prevent recirculation of flue products from an adjacent vent cap into the combustion air inlet, follow all applicable clearance requirements in the latest edition of the National Fuel Gas Code and/or CAN/CGA-B149 Installation Code and instructions in the Installation and Operation Manual. Clearances You must install the combustion air inlet cap at least one foot (0.30 m) above ground level and above normal snow levels.
Installation & Operation Manual 2 Venting (continued) WARNING 3' MIN 12" MIN Only use a sidewall air inlet cap supplied by the appliance manufacturer or a rooftop air inlet cap supplied by either the vent or appliance manufacturer. Using any other air inlet cap for single unit installations or using a common air inlet cap for multiple units with insufficient free area and/or protections from wind and weather may result in operational problems and the spillage of flue products.
Installation & Operation Manual 2 Venting Sidewall venting - see page 14. C NOTICE Before installing a venting system, follow all requirements found in the General Venting section. This option uses a powered vent assembly which pulls the flue products out of the stack. This fan generates a negative draft at the unit. Combustion air is drawn from the equipment room (see Combustion and Ventilation Air on 10).
Installation & Operation Manual 2 Venting (continued) Terminate the venting system at least 3 feet (0.9 m) above any forced air inlet within 10 feet (3.05 m). Terminate the venting system at least 4 feet (1.2 m) below, 4 feet (1.2 m) beside, or 1 foot (30cm) above any door, window, or gravity air inlet into any building. Locate vent termination at least 8 feet (2.4 m) horizontally from any combustion air intake located above the sidewall termination cap.
Installation & Operation Manual 2 Venting WARNING Do not combine the flue from this unit with the vent from any other appliance. Do not combine flues from multiple appliances into a common vent. The flue from this unit must be a dedicated stack. Connect the flue vent directly to the flue outlet opening on the top of the unit. Make the connections from the unit vent to the outside stack as direct as possible with no reduction in diameter.
Installation & Operation Manual 2 Venting (continued) Horizontal DirectAire™ venting (Powered Venting) - see page 14. D 3' MIN 12" MIN NOTICE Before installing a venting system, follow all requirements found in the General Venting section. The Horizontal DirectAire™ vent system is the same as the Sidewall Venting system, except it pulls combustion air from the outdoors through a sidewall air inlet. Follow all requirements in Sidewall Venting section on page 22.
Installation & Operation Manual 2 Venting E Direct venting - see page 14. NOTICE Before installing a venting system, follow all requirements found in the General Venting section. This option uses sealed AL29-4C vent materials for the flue outlet piping and separate combustion air inlet piping. This system terminates both the flue and combustion air inlet in the same pressure zone. The flue outlet and combustion air intake may terminate at either a sidewall or the rooftop.
Installation & Operation Manual 2 Venting (continued) Masonry chimney installation Do not use a standard masonry chimney to directly vent the combustion products from this unit. To use a masonry chimney, the chimney must use a sealed, corrosion-resistant liner system. Sealed, corrosion-resistant liner systems (single-wall, double-wall, flexible, or rigid) must be rated for use with a high efficiency, positive pressure vent system.
Installation & Operation Manual 2 Venting Length of air inlet pipe The installed length of air inlet pipe from the unit to the outside air inlet cap must not exceed 50 equivalent feet (15.2 m). Subtract 5 feet (1.5 m) of equivalent length for each 90° elbow. Subtract 2.5 feet (0.7 m) of equivalent length for each 45° elbow. Do not exceed the limits for the combustion air inlet piping lengths.
Installation & Operation Manual 2 Venting (continued) 2. For PVC, CPVC, ABS, dryer vent, or flex duct air inlet piping, use a silicone sealant to ensure a proper seal at the unit inlet and the air inlet cap. 3. For Dryer vent or flex duct, also use a screw-type clamp to attach the inlet vent material to the unit inlet and the air inlet cap. Properly sealing the air inlet pipe ensures that combustion air will be free of contaminates and supplied in proper volume. 4.
Installation & Operation Manual 2 F Venting Outdoor installation - see page 14. NOTICE Before installing a venting system, follow all requirements found in the General Venting section. Units are self-venting and can be used outdoors when installed with the optional outdoor cap. This cap mounts directly to the top of the unit and covers the flue outlet and combustion air inlet openings. No additional vent piping is required.
Installation & Operation Manual 3 Gas connections Connecting to gas supply Verify that the appliance is supplied with the type of gas specified on the rating plate. This appliance is configured for operation up to 4,500 feet altitude. Consult factory for installations above 4,500 feet elevation. Inlet gas pressure: Measured at the inlet pressure tap on the appliance gas manifold. The pressure tap is located upstream of the combination gas valve(s). See Table 3A for maximum and minimum inlet pressures.
Installation & Operation Manual 3 Gas connections 2. Use new, properly threaded black iron pipe free from chips. If you use tubing, make sure the ends are cut square, deburred and clean. Make all tubing bends smooth and without deformation. Avoid flexible gas connections. Internal diameter of flexible lines may not provide unit with proper volume of gas. 3. Install a manual main gas shutoff valve at the unit’s gas inlet, outside of the unit. 4. Run pipe or tubing to the unit’s gas inlet.
Installation & Operation Manual 3 Gas connections (continued) Combination gas valve/regulators equipped with integral vent limiters are not required to have vent or relief lines piped to the outdoors. The termination of the vent limited opening on the combination gas valve/regulator complies with the safety code requirements of CSD-1, CF-190(a) as shipped from the appliance manufacturer without the installation of additional vent lines.
Installation & Operation Manual 4 Water connections Install piping from the filter system to the pool heater as shown in the pool heater piping diagrams. See Figures 34 - 38. Minimum pipe diameter to and from the installed pool heater to the filter system piping on models 502 - 752 is 2" and on models 992 - 2072 Btu/hr the minimum is 2-1/2". The piping from the filter system to the pool heater may be PVC, CPVC or Copper Pipe.
Installation & Operation Manual 4 Water connections (continued) 6 - 90° elbows 2 - ball valves 2 - unions .................................................................. 1 - cold water tee Not more than 45 feet of straight pipe. For every elbow and tee in excess of those shown above, deduct 5 feet from the maximum allowable straight pipe in the pool heater to the system circulating loop.
Installation & Operation Manual 4 Water connections Figure 4-3_Heater Within 15 feet of Pool Piping AUTOMATIC BYPASS VALVE * NOTE: IF THE RETURN SYSTEM SENSOR IS LOCATED IN THE SECONDARY LOCATION SHOWN ON THE PIPING DIAGRAM, THE UNIT PUMP MUST RUN CONTINUOUSLY TO ENSURE THE WATER FLOW PAST THE POOL RETURN SENSOR * SENSOR IS MAINTAINED.
Installation & Operation Manual 4 Water connections (continued) Figure 4-5_Cascaded heaters Within 15 feet of Perpendicular Pool Piping AUTOMATIC BYPASS VALVE * POOL RETURN SENSOR SECONDARY LOCATION PVC MIN (SEE TABLE) RECOMMENDED ISOLATION VALVE COPPER OR CPVC (SEE TABLE) COPPER OR CPVC (SEE TABLE) FROM POOL POOL RETURN SENSOR PRIMARY LOCATION VALVE 110° LIMIT 3' MIN TO POOL MODEL NO CP (N,L) 502-752 CP (N,L) 992-2072 REQUIRED POOL RETURN SENSOR LOCATION BYPASS PIPE SIZE 2" MIN 2-1/2" MIN *
Installation & Operation Manual 4 Water connections Figure 4-7_Multi-stack frame - Cascaded heaters beyond 15 feet of pool piping MODEL NO CP (N,L) 502-752 CP (N,L) 992-2072 BYPASS PIPE SIZE 2" MIN 2-1/2" MIN POOL RETURN SENSOR LOCATION FROM POOL 3' MIN PRIMARY LOCATION POOL SUPPLY SENSOR 4" PVC 110° LIMIT FLOWMETER TO POOL LEADER MEMBER TABLE 4A PIPE SIZING CHART COMMON PIPE SIZE (MIN) NUMBER OF UNITS MODELS 502-752 MODELS 992-2072 1 2" 2-1/2" 2 3" 4" 3 3-1/2" 4" 4 4" 5" 5 5" 6" 6 5" 6" NOTIC
Installation & Operation Manual 4 Water connections (continued) Pumped Automatic Bypass This is a high efficiency pool heater which requires a special pumped bypass for proper operation. The bypass assembly supplied with the pool heater includes a pump and a 3-way mixing valve. All piping to connect the filter system to the pool heater is made directly to the bypass piping on the pool heater. Note: The actuator handle is not used when the outdoor cover is installed.
Installation & Operation Manual 4 Water connections Relief valve This pool heater is supplied with a relief valve(s) sized in accordance with ASME Boiler and Pressure Vessel Code, Section IV. The relief valve(s) is installed in the vertical position and mounted in the hot water outlet. Place no other valve between the relief valve and the pool heater. To prevent water damage, pipe the discharge from the relief valve to a suitable floor drain for disposal when relief occurs.
Installation & Operation Manual 5 Electrical connections General information WARNING 3-way automatic bypass valve wiring ELECTRICAL SHOCK HAZARD – For your safety, turn off electrical power supply before making any electrical connections to avoid possible electric shock hazard. Failure to do so can cause severe personal injury or death.
Installation & Operation Manual 5 Electrical connections Pool heater operating control module The operating control for the appliance is the SMART SYSTEM control module. It is located on the inside of the control panel, behind the front access door. Access to adjust the temperature set point and other user adjustable points is made through the Operator Interface located on the front access door. Label all wires prior to disconnection when servicing controls.
Installation & Operation Manual 5 Electrical connections (continued) Low voltage connections Louver relay 1. Route all low voltage wires through the knockouts on the left side of the heater, as shown in FIG. 5-3. When the heater is to control combustion air louvers, a field provided 24VAC louver relay must be installed. Connect the Louver Relay Coil terminals to the louver relay coil. 2. Connect low voltage wiring to the low voltage connection board as shown in FIG.
Installation & Operation Manual Electrical connections The return sensor of the Leader heater should be placed in the main system piping loop, upstream of the water being supplied to all the heaters (see FIG.’s 4-5, 4-6, and 4-7). The return sensors on the remaining Member heaters may also be placed in the same location as the Leader or they can be placed in each Member’s PVC piping loop in the Alternate sensor location, using the tapped sensor hole (FIG. 4-3).
Installation & Operation Manual 6 Startup Pre-start checklist Before attempting to start the pool heater verify that the following items have been checked: 1. 2. 3. 4. 5. 6. 7. 8. Verify proper location and installation of the pool heater. Check gas piping and ensure the gas line is purged of all air. Ensure that the pool is properly filled. DO NOT operate pool heater if improperly filled. Check to ensure that all water connections are tight. Relief valve has been piped to a suitable floor drain.
Installation & Operation Manual 6 Startup If freeze protection is not provided for the system, a low ambient Placing the pool heater in operation temperature alarm is recommended for the equipment room. Pool heater operational checks Damage to the pool heater by freezing is non-warrantable. 1. Turn the pool heater main power switch to the “ON” position. 1. Pump Operation - MOST IMPORTANT - This pool heater 2.
Installation & Operation Manual 6 Startup (continued) Figure 6-2_Operating Instructions FOR YOUR SAFETY READ BEFORE OPERATING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance is equipped with an ignition device which automatically lights the burner. Do not try to light the burner by hand. B. BEFORE OPERATING smell all around the appliance area for gas.
Installation & Operation Manual 6 Startup Set clock Configuration of the cascade The SMART SYSTEM control has a built-in clock that it uses for its night setback feature and for logging events. This clock must be set when the appliance is installed, and anytime the appliance has been powered off for more than one month. Use the following procedure to set the clock: When installed in a Cascade system, the individual controls must be programmed for cascade operation.
Installation & Operation Manual 7 Operating information General How the appliance operates The Copper-fin2 uses a copper finned tube heat exchanger to transfer heat from the flue products to the water. An electronic control module monitors various inputs to initiate a call for heat. The blower provides both primary and secondary air to the burner and forces the flue products out of the combustion chamber and into the vent system.
Installation & Operation Manual 7 Operating information The control monitors the temperature difference between the inlet and the outlet sensor. If this difference exceeds the first limit the control will turn off stages. If the temperature difference exceeds a second limit the control will shut the unit down. The unit will restart automatically once the temperature difference has dropped 10°F (6°C) and the minimum off time has expired.
Installation & Operation Manual 7 Operating information (continued) Cascade When multiple appliances are installed, they can be wired together in a cascade sequence. A maximum of eight appliances can be controlled from a single control. In this application one appliance would be designated as the Leader control and all others would be designated as Member controls. The set point or firing rate can be controlled by the 0 - 10V input as well.
Installation & Operation Manual 7 Operating information Sequence of operation OPERATION DISPLAY 1. The high limit may require reset through the display before HTR: Standby OUT: 123.8F( 78) any action will take place. 2. Upon a call for heat the control turns on the unit pump. The HTR: Standby OUT: 123.8F( 78) flow switch and low water cutoff (if equipped) must close. 3. • If the unit is equipped with a proof of closure valve, the proof of closure switch must be closed.
Installation & Operation Manual 7 Operating information (continued) Copper-fin2 control module Use the control panel (FIG. 7-1) to set temperatures, operating conditions, and monitor appliance operation.
Installation & Operation Manual 7 Operating information Access modes User The user can adjust the space heating target temperature and the tank target temperature (if a tank sensor is used) by using the UP and DOWN buttons (FIG. 7-1) at any time during normal operation. By entering the USER code (0704), the user can also change temperature units, time and date, and night setback settings.
Installation & Operation Manual 7 Operating information (continued) Status display screens Status Display Screens By using the Previous/Next (, ) arrow keys on the SMART SYSTEM display panel, you can navigate through the 11 display screens. Each screen will contain two (2) viewable items.
Installation & Operation Manual 7 Operating information Status Display Screens (cont’d) By using the Previous/Next (, ) arrow keys on the SMART SYSTEM display panel, you can navigate through the 11 display screens. Each screen will contain two (2) viewable items. The following is a description of the individual items and what they can display: Screen # Screen #3 Line 2 Display shows: Description SYSRTN: ***F (***) The system return sensor acts as the control sensor.
Installation & Operation Manual 8 Maintenance Maintenance and annual startup Table 8A_Service and Maintenance Schedules Service technician (see the following pages for instructions) Owner maintenance • Check appliance area General: • Address reported problems • Inspect interior; clean and vacuum if necessary; Daily • Check pressure/temperature gauge • Check for leaks (water, gas, flue, condensate) ANNUAL START-UP • Examine venting system • Check system water pressure/system piping/expansion tank
Installation & Operation Manual 8 Maintenance WARNING Follow the service and maintenance procedures given throughout this manual and in component literature shipped with the appliance. Failure to perform the service and maintenance could result in damage to the appliance or system. Failure to follow the directions in this manual and component literature could result in severe personal injury, death, or substantial property damage.
Installation & Operation Manual 8 Maintenance (continued) Check relief valve Inspect/replace hot surface igniter 1. Inspect the relief valve and lift the lever to verify flow. Before operating any relief valve, ensure that it is piped with its discharge in a safe area to avoid severe scald potential. Read Section 4 - Water Connections of the Copper-fin2 Installation and Operation Manual before proceeding further. This unit uses a proven SMART SYSTEM control module and a hot surface igniter.
Installation & Operation Manual 8 Maintenance Perform start-up and checks Check flue gas passageways Start appliance and perform checks and tests specified in Section 6 - Start-up of the Copper-fin2 Installation and Operation Manual. Any sign of soot around the inner jacket, outer jacket, flue pipe connections, burner or in the areas between the fins on the copper heat exchanger indicates a need for cleaning.
Installation & Operation Manual 8 Maintenance (continued) Inspect and clean the heat exchanger 1. While burners are removed, check the heat exchanger surface for sooting. If present, heat exchanger must be cleaned and problem corrected. Proceed as follows. 2. Remove gas manifold(s)/orifice assemblies as described in steps 1 through 5 in Burner Removal and Cleaning, page 60. 3. Disconnect wiring from the hot surface igniter and remove igniter from the door panel to prevent damage to the igniter. 4.
Installation & Operation Manual 9 Connection diagram FIELD WIRING + ALARM 1 + CONTACTS 2 3 + RUNTIME TO MONITORING DEVICE + CONTACTS 4 + OPEN 3-WAY 5 + OPEN 24V CLOSE CLOSE CN4 VALVE 6 + COM COMMON 7 + S1 STAGE #1 8 S1 9 + + S2 CONNECT STAGE #2 10 S2 TO + 11 TERMINAL 12 + S3 STAGE #3 #19 S3 + 13 (LOUVER 14 + S4 STAGE #4 RELAY) + S4 15 COM FIELD CN5 16 + LOUVER PROVING SWITCH SUPPLIED PROVE + 17 + LOUVER RELAY LINE WIRING R 18 M + COIL 19 + NEU TANK 20 AQUASTAT + AQUASTAT 21 CN3 TANK SENSOR 22 + TANK + SE
Installation & Operation Manual Connection diagram LT HARNESS Notes: 1. All wiring must be installed in accordance with : local, state , provincial and national code requirements per either N.E.C. in USA or C.S.A. in Canada. 2. If any original equipment wire as supplied with the appliance must be replaced , it must be replaced with wire having same wire gauge (AWG) and rated for a minimum of 105°C 3. Actual connector block locations may vary from those shown on diagrams .
L 64 NOTE: Not all connections/features apply to pool heaters.
X6-7 CN5-12 CN5-4 TANK TSTAT B A X8-7 COMPUTER DISPLAY BOARD X8-16 X8-6 X8-17 CN6-7 CN6-3 X7-4 X7-8 CN6-5 CN6-10 X8-15 X8-5 X6-15 X6-6 CN6-9 CONNECTION BOARD 2 CN1-7 + SYSTEM PUMP CN1-8 SPEED INPUT - CASCADE 0-10V + RATE OUTPUT - 0-10V + BMS INPUT - CN6-4 X6-14 CN5-10 STAGE 4 LOUVER PROVING X6-11 CN5-3 STAGE 3 X13-1 CN5-9 X6-2 X6-16 STAGE 2 CN5-7 CN5-1 X6-1 X6-5 X6-12 CN5-8 CLOSE OPEN PROBE TEST X6-3 X11 X4 CN5-11 10K X8-20 X8-10 X8-18 X8-12 X8-1 X4-2
Notes 66
Notes 67
Revision Notes: Revision A (ECO #C08226) initial release. Revision B (ECO #C08423) reflects updates made to images and text as a result of questions/requests from the field.