Golf and Turf Series GT-126 and GT-122 Operator’s Manual Locke Turf 307 Highway 52E, Opp, Alabama, 36467, (334) 493-1300
CONGRATULATIONS You have invested in the best implement of its type on the market today. The care you give your Locke Turf implement will greatly determine your satisfaction with its performance and its service life. We urge a careful study of this manual to provide you with a thorough understanding of you new implement before operating, as well as suggestions for operation and maintenance. If your manual should become lost or destroyed, Locke Turf will be glad to provide you with a new copy.
Commercial Series Operator’s Manual Table of Contents SECTION Introduction …………………………....2 Warranty ………………………………...3 Safety Important Safety Information …………..4 Training …………………………………..4 Preparation ……………………………....4 Operation ………………………………...4 Maintenance and Storage ……………...4 Operation Starting the Engine ……………………...6 Raising and Lowering of Cutter Unit …..6 Height of Cut Adjustment ……………….6 Mowing …………………………………...6 Loading and Unloading for Transport …6 Maintenance Lubrication ………………………………………..
INTRODUCTION More than merely devices created for mowing grass, the excellence of design, construction and operation of Locke power mowers is unparalleled. First introduced in 1928, tested and proven, Locke power mowers may be considered, in terms of today’s technology, the ultimate response to the need for the highest degree of quality lawn care.
LOCKE MOWER 2 Year Limited Warranty WARRANTY PERIOD AND COVERAGE A. Locke Turf, Inc. warrants to the original purchaser, and to subsequent owners, that the registered Locke Mower will be free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original owner. B. Locke Turf, Inc. will, at its discretion, replace any component or authorize the mower to be repaired, when a defect in material or workmanship has been determined. C.
SECTION 1—SAFETY IMPORTANT SAFETY INFORMATION OPERATION This Safety Alert Symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! The Safety Alert Symbol identifies important safety messages in manuals and on equipment safety signs. To avoid possible injury or death, follow the equipment and manual’s safety instructions.
SECTION 2—GENERAL HEIGHT OF CUT ADJUSTMENTS The GT Series is engineered and designed to offer the most accurate adjustments to produce pristine cutting. An Accu-Gauge is recommended to measure the settings. A two point gauge can also be used to maintain and measure proper settings. 2 Point Gauge Accu-Gauge Ensure that the rear roller is slightly higher than the front roller in order to maintain the proper “attitude.
SECTION 3—OPERATION STARTING THE ENGINE MOWING Check to see that the oil in the crankcase is at the proper level and there is fuel in the tank. Make sure that the tractor clutch lever, on the right handlebar, and the reel clutch lever, on the left handlebar, are released before attempting to start the engine. Set the engine kill switch to the on position, move the throttle to a slightly open position, close the carburetor choke valve, then pull on the recoil starter rope.
SECTION 4—MAINTENANCE as reel link arms, reel bearing housings, etc. have sintered bronze bushings. LUBRICATION There are 4 pressure lubrication points on the mower. All are zerk type grease fittings. Use a quality light grease at these points. The bronze clutch collars each have a grease fitting. These are located at the front of the tractor on the left and right sides underneath the main guard. Lubricate with 1 or 2 shots of grease every 10 hours of operation. The caster post has a fitting.
REEL BEDKNIFE MAINTAINING BLADE SHARPNESS Whenever the bedknife is replaced it is essential that the reel and blade be ground or lapped to alignment. To provide consistent performance, lap the cutter blades on a regular basis, ideally after every 40 to 60 hours of operation. Your dealer will be able to assist you in maintaining Locke’s legendary cut. If you have the equipment to lap your reel, follow the steps below. 1. Loosen the reel adjusting screws enough to cause a slight friction on the bedknife.
RESHARPENING REELS RESHARPENING BEDKNIVES For maximum performance and to achieve the finest cut, reels should be reground with a relief. For best results, the “land” area should be no wider than 1/64” to begin the season. (See figure below) Modern reel grinders are capable of producing a relief, finishing off the cylinder with a light spin grind. Depending on the amount of use, bedknives may be resharpened once or twice before replacing them is necessary.
Locke Turf 307 Highway 52E, Opp, Alabama, 36467, (334) 493-1300
