Installation & Assembly

2930 & 2945 Narrow Stile
Installation Instructions
Connued on Reverse Side
IMPORTANT INFORMATION ABOUT YOUR 2930/2945
1. The Lockey 2930 & 2945 are designed for narrow sle prep doors
or for configuraons with exisng narrow sle hardware with 1 1/8”
prep. The 2930 & 2945 can also be installed on new morse prep
doors, 2”x2” gates or chainlink gates.
2. The drive/spindle hole is located on the boom of the latch. The
system operates opposite compared to Adams-Rite style products.
The strike may need to be modified.
3. When the door is closed, the system locks automacally.
4. From the inside, unlock using the thumb turn/lever handle.
5. From the outside, unlock by pressing ‘C’ (CLEAR), followed by
your User Code.
Step 1: Change User Code/Combinaon (OPTIONAL)
To change user code/combinaon, see instrucons on reverse side.
Step 2: Prep Door for Installaon with Template
Place template (supplied) on door and fold along door’s edge. Check to ensure proper measurements. Drill holes accordingly.
Step 3: Idenfy Door Handing
Right-Hand Doors – From exterior of door, hinges are on right side (Fig. 1).
Le-Hand Doors – From exterior of door, hinges are on le side (Fig. 2).
The 2930 & 2945 are factory pre-handed for right-hand doors.
To change handing, remove two blue screws and cover plate from Outside Body.
Move the pin from the right side of the Outside Body to the hole on the le side.
Replace plate and screws.
Note: For 2930 DC (Double Combinaon), Inside Body handing must be opposite from Outside Body.
Install at least one Support Pin (#11) in posion ‘A’/posion ‘B’ on the Outside Body as shown in Fig. 3.
Now, install/screw Hex Bolts (#8) into the top and boom of the Outside Body as shown in Fig. 3.
Step 4: Change Latch Handing (if necessary) & Install Latch
IMPORTANT: Do NOT remove Cam from latch when changing handing.
Cam Posion: MUST be on LEFT side of latch.
If latch does not pull and twist, proceed with the following steps:
1. Remove screws from both sides of latch casing.
2. Remove cover and interior springs (#1, #2, #3).
3. Remove latch and deadlatch (#4, #8).
4. Carefully remove Latch Pin (#7) and Latch Spring (#6).
5. Replace the Latch Spring (#6) and then move the Deadlatch Acvator (#5)
to the opposite side of the latch, ensuring that it depresses the Latch Spring.
6. Replace the Latch Pin.
7. Replace Latch, Deadlatch, Latching Springs and Cover.
8. Secure Screws on each side of the Latch Casing.
Place the Narrow Sle Deadlatch (#4) in the door prep and secure.
Fig. 3
#8 Latch
#7 Latch Pin
#4 Deadlatch
#2 Small Spring
#1 Cover
#3 Large Spring
#5 Deadlatch Activator
#6 Latch Spring
Cam
No. Part Name
# included
2
1
3
4
Outside Body
Inside Body
Rubber Trim Plates
Narrow Sle Deadlatch
Strike Plate
Hex Bolts
Extra Code Tumblers (Red)
Extra Non-Code Tumblers (Blue)
Support Pin
Tweezers
Screw Kit
7
8
9
10
11
12
13
1
1
2
1
1
2
2
4
2
1
1
Spindle (30-45mm & 40-55mm)
5 2
Latch Face Plate
6 1
Updated 5.12.16








11
12



A
B



11
11
